Search Documents

By C. D. Demond

In reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500" F. and another only 2,100 F., while the "critical" temperature is 2,000" F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature in a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 1, 1915

By Etienne A. Ritter

The Evergreen mine, located at Apex, in the northern part of Gilpin county, Colorado, has opened a very peculiar and interesting copper-deposit, in which both bornite and chalcopyrite occur as rock-minerals. The country-rocks are crystalline schists cut by dikes of granu-lite and of pegmatite. At the Evergreen property they have been cut by a dike of a uew kind of eruptive rock, to which I have given the name " Evergreenite." The rock is composed of quartz, alkali feldspars, orthoclase and albite (often interlocked as microperthite), with augite of the ægirine variety and long needles of enstatite and diallage. For reasons stated below, I believe the dike to be of Tertiary age. It is easily traced on the surface of the ground, from a point in the bottom of Pine creek, about a mile below Apex, to the top of Nevada hill, 1,500 ft. beyond and 600 ft. above it. (See Fig. 1.) It varies from 3 to 12 ft. in width, and is bounded on both sides by contact-zones about 60 ft. wide, in which the crystalline schists have been changed into pseudo-quartzites or pseudo-gneisees, according to the injection of an excess of quartz or of feldspars through the special layer of the schists. The most interesting feature is the presence of the pyroxenes, which are always found, though in very variable proportions from place to place, in the layers of these metamorphosed crystalline schists. The dike has torn from its walls a large number of fragments of the wall-rock. It must have been in a viscous state when that happened, because these fragments of the wall-rock do not show any sign of resorption or of assimilation by the magma. In places they are so distinct and so numerous that the rock looks to the naked eye like a pseudo-breccia, of which, never-

Jan 1, 1908

TULSA, the host of the Petroleum Division this year, is the oil metropolis of the Mid- Continent and gateway of the Southwest. It has risen in less than three decades from a dusty cattle town of less than 1000 population to its present-day status of a modern, wide-awake and prosperous city of close to 150,000, with an assessed realty valuation of approximately $100,000,000. Oil was discovered near Tulsa in 1901, and with it came th.2 development of the Mid-Continent field, one of the richest in the world. Tulsa from the start has been the center of operations, and its location on foul- and aggressive application of the airplane to oil-field requirements tends to fix this status as production is developed farther and farther afield. That Tulsa is far more than an ephemeral oil town is punched into the newcomer's- especially the Easterner's-mind, as he is whisked by taxi from the railroad station to the Hotel Mayo. The cicadalike pounding of the riveters on the steel skeletons of many skyscrapers, mounting upward to fill the gaps in an already well-developed skyline, dispels the feeling of a new atmosphere and puts him back on Forty-second Street, Michigan Boulevard or whatever his own particular "Main Street" may be along which an American city is being remade. Practically every company of any importance operating in the Mid-Con-

Jan 1, 1928

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem'ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam'ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

By A. W. McReynolds

One characteristic of plastic deformation which distinguishes it from elastic strain is the essential inhomo-geneity of plastic strains. Elastic strain varies continuously through a material, and average relative displacements of initially adjacent atoms are only small fractions of their initial spacing, (strains of the order of 0.01 or less). On the other hand, plastic flow corresponds to the appearance of discontinuities in strain of the lattice, such as dislocations or slip bands, where local strain, on an atomic scale, is several orders of magnitude higher. These discontinuities are visible on a microscopic scale as the familiar slip lines (Fig 1). In spite of this obvious microscopic inhomogeneity, however, macroscopic measurements almost invariably show a smooth curve of stress vs. strain (Fig 2b) even if measurements of linear strains be made to an accuracy of one part in 107. This macroscopic homogeneity of strain indicates that the discontinuities in strain on slip planes occur in increments too small or too slow to be recorded individually, and further that they occur sufficiently independent of one another so that the small increments add at random to a smooth stress-strain curve. The present paper describes observations of plastic strain in aluminum of commercial purity and in high purity Al-Cu alloys, where there exists a strong coupling between slip in various regions of the specimen such that once initiated it spreads rapidly through a large volume. The total effect is that of relatively large, rapid, and regularly spaced steps of strain followed by periods of only elastic strain. Fig 2a illustrates the type of "stair-step" stress-strain curve which results. The properties of this cooperative slip phenomenon will be described further in the section on results: in par- ticular it will be shown that each step corresponds to the propagation of a wave of plastic deformation through the specimen. Some interpretations of the mechanism by which it occurs will be made in the following section. Although the type of plastic wave phenomena to be described has not previously been reported, there are numerous cases of related effects in the plastic yielding of metals: YIELD POINT PHENOMENA The most familiar of such effects is the "yield point" observed in low carbon steels, brass, duralurninum, and the like. It consists in the sudden termination of the elastic portion of the stress-strain curve by a large plastic strain. Since the usual tensile machine is such that yielding of the specimen relieves the load, the resulting curve is as shown in Fig 3. As the strain continues, deformation occurs at a lower stress for some time, then follows a rising curve, but with no further sudden yielding. This effect has been observed in brass by Sachs and Shojil and later by many others. Edwards, Phillips and Jones2 made extensive studies of the effect in steel, and of the role of various alloying elements. Although there seems to be fairly clear evidence that the yield point is caused by a hardening of the material by precipitation of impurities, no satisfactory explanation for the sudden yielding has been given. Winlock and Leiter3 have shown that the strain. level of the upper yield point depends strongly on the rate of loading, the yield point increasing by almost a fac- tor of two as the strain rate goes from 0.002 in. per in. per min. to 4.4 in. per in. per min. This effect would seem to imply an incubation period before yielding is initiated at a certain stress. On the other hand, by going to very slow loading rates, Edwards, Phillips and Jones2 showed that the yield point does not become lower and eventually disappear as might be expected, but, on the contrary, begins to rise at loading rates below about 25 Ib per in. per min. becoming much higher than at rapid loading rates. STRAIN AGING If, instead of continuing straining of a specimen after occurrence of a yield point, the load is removed and the specimen aged, resumption of the test results in occurrence of another yield point as shown by the dotted curve of Fig 3. The new yield stress is generally higher than the previous maximum applied stress. This hardening of the material by straining and subsequent aging is undoubtedly related to quench age-hardening resulting from the aging of a specimen quenched from high temperature. Since neither effect is observed in pure metals, it is generally accepted that quench-aging in all cases is the result of hardening by precipitation of a supersaturated alloying element, and that strain-aging is probably a similar precipitation, accelerated by disruptions of the lattice by previous strain. Pfeil4 has shown that strain-aging does not occur in iron from which all of the carbon has been removed, but that only a very small carbon content, around 0.003 pct, is necessary to cause strain-aging. In accord with this observation is recent work by Dijkstra5 in this laboratory showing that the solubility limit of carbon in iron is extremely low, less than 0.001 pct at 400°C. Edwards, Phillips and Jones2 have shown that the strain-aging effect is also removed by the addition of small quantities of elements such as Mo, Mn, Ti, and the like, which readily form carbides. Their results demonstrate the

Jan 1, 1950

By S. W. Miller

Most of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,' that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., he has since found large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than % in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top 1/16 in (1-5 mm.) of the weld, they were removed by the grinding or machining; also, welds 3/4 in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was decided to find where the rupture occurred in various kinds of welds made

Jan 1, 1920

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By M. F. Burr, F. V. Lenel, G. S. Ansell

The mechanism of materials transport was studied in a model experiment in which a silver sphere was sintered to a silver plate under an applied external stress near 800° C. For this purpose the rate of growth of the neck between the sphere and the plate which is proportional to the strain rate of the creep process involved in a neck growth was determined by measuring the change in electrical resistance of the away. This rate of neck growth will depend upon the magnitude of the applied external stress. By measuring the rate just before and just after a change in the external load and therefore the applied stress, the relationship between strain rate and stress can be derived. For material transport by slip in a pure metal it is expected that the strain rate should be proportional to the 4.5th power of the stress, while for transport by diffusional flow the strain rate should be proportional to the first power of the stress. It was found that for stresses above 5 X 10' dynes per sq cm (70 psi) the exponent in the stvain rate-stress relationship was near 4.5 while for a stress of 0.7 x 108 dynes per sq cm (10 psi) an exponent of 1.8 was determined indicating that under the conditions of the experiment the transport mechanism for creep in silver shifts from diffusional flow to slip in the region of 0.7 x 106 dynes per sq cm (10 psi). The importance of these findings for an understanding of the mechanism of material transport in conventional sintering (without an external load) is pointed out. In a paper by Early et al.,' the mechanism of material transport during sintering was treated as a creep process. It was pointed out that two possible types of creep processes could operate during sintering. In one of these material transport takes place by vacancy diffusion due to a gradient in chemical potential. The vacancy sinks in this diffusion process may be either grain boundaries, as in Herring-Nabarro microcreep, or regions beneath a surface of small radius of curvature. The diffusive transport may be by volume, grain boundary, or surface diffusion. In the other mechanism, creep takes place by slip, i.e., dislocation motion with its rate generally controlled by dislocation climb. One method of distinguishing between these two modes of materials transport is to investigate the creep rate, i.e., the rate of material transport as a function of stress. For material transport by vacancy diffusion, the creep rate is proportional to the stress.' For creep by slip, controlled by dislocation climb, the creep rate is proportional to a power of the stress. For pure metals this power is 4.5;374 for dispersion-strengthened material a fourth power relationship can be derived.5 This difference in the stress dependence of the strain rate is illustrated schematically in Fig. 1, in which the logarithm of strain rate is plotted vs the logarithm of the stress for material transport in a pure metal by vacancy flux and by dislocation climb. The stress range in which the two types of material transport overlap would be expected to be relatively small. In the experiments described by Early and coworkers compacts pressed from spherical copper powder were sintered isothermally under an applied axial external load in a dilatometer. During sintering the magnitude of the applied external load was changed and the rate of axial shrinkage of the compact before and after the load change determined. In order to find the stress dependence of the strain rate the magnitude of the stress acting on the neck area between the spherical particles before and after the load change had to be calculated. This stress is the resultant of the stresses due both to the externally applied load and to surface tension. The stress due to surface tension is a function of the geometry of the powder compacts. It can be determined, at least for simple geometrical arrays,'76 but it is difficult to obtain exact values of the stresses for actual powder compacts when only average values of particle diameters and of neck diameters between particles are available. The calculation of stress and the strain rate-stress relationship is therefore only very approximate.

Jan 1, 1968

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By F. O. Shuck, F. E. Butler

A diaphragm diffusion cell suitable for use with liquid metals was designed and tested by measuring the diffusion coefficients for a Hg-10 pct In alloy at 25°C. The binary diffusion coefficient and the coefficients for In and Hg tracers were measured at this composition. The measured coefficients for both tracers were less than the binary diffusion coefficient. When these coefficients were combined with the activity correction term of Darken, the predicted binary coefficient was somewhat higher than the experimental value. In recent years a number of investigators have been studying diffusion of liquid metals in order to gain a better understanding of the liquid state and to examine possible applications to liquid metal processing. The bulk of this work has involved either self-diffusion or diffusion of low concentrations of solute metals in an essentially pure solvent metal. The most common experimental technique employed has been the capillary-reservoir method of Anderson and saddington1 since it is well-suited to measurements involving low concentrations of solutes. As an expansion of previous studies, an investigation of the variation of diffusion coefficient over large composition ranges has been undertaken in this laboratory. Although it is possible to modify the capillary-reservoir method for such measurements, the technique loses its principal advantage of requiring only small quantities of solutes. Therefore, it was felt desirable to investigate other possible experimental techniques applicable to measurements over large composition ranges. A technique which has been used widely in measurements of other liquid systems and seemed potentially applicable to studies of liquid metals was the diaphragm cell. This method has been found to combine relative simplicity of operation with accurate and reproducible results. In use with normal liquids, the tyiical diaphragm cell utilizes a porous glass disk. However, because of the high surface tension, it is not possible to use a diaphragm of such fine pore structure with liquid metals. Furthermore. projected use at high temperatures makes the use of glass undesirable. Consequently, the first problem was the search for an appropriate cell design. EXPERLMENTAL Diaphragm Cell. A number of possible cell designs were examined. Prototypes of several were constructed and tested. The final design is shown in an exploded view in Fig. 1. The cell consists of two identical chambers, one on either side of a 0.20-in.-thick partition. The chambers are 0.15 in. deep and have a volume of 3.45 cu cm. Each chamber is provided with two small threaded holes for filling and emptying. The filling holes may be sealed with stainless-steel screws. Drilled lengthwise through the center partition is a 0.250-in.-diam hole. Inserted into this hole is a rod having seven 0.059-in.-diam holes drilled radially through it. The total "hole" volume is 0.078 cu cm. When the rod is properly aligned, the holes in it constitute the "diaphragm" through which diffusion occurs. The center section was of Teflon and the rod and face plates were of Plexiglas. Four such cells were constructed and used in this study. Subsequent to this investigation, a similar cell constructed entirely of iron was fabricated and tested at higher temperatures. Several considerations led to this final design. It is desirable to minimize the volume of the cell chambers to decrease the time required for a measurement. However, the total volume of metal in the diaphragm must be small in comparison with that in the chambers. To facilitate filling and emptying it is desirable to have a diaphragm which may be closed.

Jan 1, 1970

By George B. Clark

THE " Munroe effect" of shaped explosive charges was discovered by Charles E. Munroe more than 50 years ago (in 1888), but it was not until World War II that it was put to any practical use. Both Allied and Axis armies used the principle effectively in bazooka projectiles, artillery projectiles and in fixed shaped charges. The first two were used primarily to combat tanks and other armor and the latter to assault pillboxes and other fixed concrete emplacements. Many engineers and others who saw the military application of the jet effect of shaped charges believed application would be possible in many industrial fields where blasting is used, such as mining and quarrying. Some work has already been done on the problem of making shaped charges applicable to mining operations. Experimentation conducted at the National Tunnel and Mines' was directed primarily along the lines of use of shaped charges for secondary blasting in connection with long-hole stoping methods. Experimentation initiated earlier and conducted by the author2 at the University of Utah on a more scientific basis was directed at revealing the basic principles of the functioning of shaped charges, as well as the feasibility of using them in mining operations after the principles of their operation had been clearly defined. It was found that: (I) a given design of charge required an optimum standoff to make it most effective, either in penetrating solid rock or steel (see Fig 3); (2) for a given design of charge there exists an optimum ratio of charge diameter to charge height above which the increase in effectiveness of the charge decreases rapidly (see Figs 4 and 5); (3) partial confinement has the effect of making charge performance much more consistent; (4) the higher power and higher velocity explosives tested are much more effective than relatively low-strength explosives; and (5) shaped charges may be adaptable to mining operations in secondary breakage and drilling blasting holes. Fig I is a diagrammatic sketch of the action of a shaped charge for two types of cavities, while Fig 2 shows the approximate manner in which the jets are believed to be formed when an explosive wave encounters the cavity, approaching it from the top. The experimentation already completed has laid the foundation for further research in the study of shaped charges. Standoff effects, effect of the strength of explosives and other features have been fairly well established. Such elements in the design of shaped charges as (I) geometry of cavity liners, (2) relative horizontal dimensions of explosive column, (3) effect of

Jan 1, 1947

By F. E. Bash

Constantan is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported and the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts against pure iron at 1500" F. (816" C.) with the cold-junction temperature at 0" F., or a proportional e.m.f. at temperatures near 1500" F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure iron. The couple was then insulated and the fire end was tied to the

Jan 1, 1921

By C. H. Li, R. J. Stokes, T. L. Johnston

Dislocation half-loops, artificially introduced by sprinkling with carborundum, were subjected to stress using three-point loading. The different stages of loop expansion and multiplication were then correlated with the macroscopic stress-deflection curve. Loop expansion started at approximately one-third of the "yield stress," defined here as the motivation stress. Above one-half of the "yield stress" simple multiplication commenced while about two-thirds of the yield stress gross multiplication developed short slip-line segments. These values were not affected by the age of surfaces exposed to both dry and wet air. Slip was not detected on unsprinkled crystals below two-thirds of the "yield stress." Thus the stress to activate intrinsic sources, defined here as the activation stress, was approximately twice the motivation stress. This relationship was independent of the strain rate used. It is concluded that lattice resistance takes the form of a viscous drag rather than a static type of force. THE importance of surface condition and environment as one of the more significant factors controlling the mechanical properties of ionic solids has recently received renewed attention.1-4 In some materials, notably the alkali halides, exposing freshly cleaved specimens to the atmosphere results in a progressive hardening and embrittlement of the crystals. This has been attributed to the surface layer becoming "aged," thereby restricting the motion of dislocations in such a way that pileup and eventually fracture results. It is necessary therefore in studying the mechanical properties of ionic crystals to inquire first into the density and distribution of dislocations in the normal cleaved surface and to understand the role these dislocations play in the onset of plastic flow. Knowledge of the effect of environment on this behavior will then assist in understanding the mechanism of embrittlement on aging. In the work reported here a method is described for studying the initiation of plastic flow from dislocation sources in the surface of magnesium oxide crystals. Preliminary results are described of the influence of surface age on this behavior. EXPERIMENTAL TECHNIQUES The magnesium oxide used in this investigation was obtained from the Norton Co. and had a nominal purity of 99.5.pct. Single-crystal specimens, having dimensions typically 1/4 by 1/8 in. cross section and 1 in. in length, were prepared by cleavage over (100) planes from the parent crystal. They were deformed under three-point loading with 3/4 in. spacing between the two end supports and a constant rate of deflection at the center of 0.001 in. per min. The maximum strain rate therefore was 1.5 X 10-5 sec-1. Reasons for choosing this particular form of loading will become apparent in a later section. In addition, a number of confirmatory type tests have been performed at higher loading rates where the maximum strain rate was increased to 1 x 10-3 sec -1. Following deformation the crystals were etched to reveal the dislocation distribution. In a previous paper5 we described a satisfactory etching solution consisting of 5 parts of saturated ammonium chloride, one part of sulfuric acid, and one part distilled water. Immersion of the crystals for 1/4 hr at room temperature developed reproducible conical etch pits at the points where dislocations emerged through the surface. It should be mentioned that dislocations freshly introduced by room temperature deformation gave sharply pointed etch pits which generally distinguished them from the almost flat-bottomed pits obtained on "grown-in" dislocations. The distinction is obvious in the photomicrograph included in Fig. 5(b). Annealing crystals at 1000°C for 12 hr on the other hand gave sharper etch pits on the grown-in dislocations and the distinction was no lower -possible; a similar observation has been reported for lithium fluoride. We have succeeded furthermore in chemically polishing magnesium-oxide crystals. Boiling in fresh 85 pct ortho-phosphoric acid for only 1 min resulted in a microscopically smooth surface which could again be etched to reexamine the dislocation distribution. This boiling time was sufficient to remove the surface damage introduced by cleavage (see next section). SURFACE DISLOCATION SOURCES There are a number of ways by which dislocations may be introduced into cleaved surfaces to act later

Jan 1, 1960

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By Theodor Knutzen, Charles H. Fulton

The plant of the National Smelting Co., a corporation controlled by the Horseshoe Mining Co., was built during 1901 to smelt the dry siliceous ores of the northern Black Hills, extracting the gold- and silver-values in a matte of low copper-percentage which is shipped to Omaha and Denver for refining. Originally, the plant was designed to collect the values of the siliceous ores in an iron-matte, which mas to be resmelted with lead-ores, in a lead-furnace, the lead-bullion produced to be refined into Doré bullion in English cupelling-furnaces. However, the scarcity of lead-silver ores in the Black Hills, owing to the present non-productiveness of the Galena district, led to

Jan 1, 1905

By Wilson Blake

A mathematical model based on the finite element method of stress analysis has been used to describe the behavior of the western wall of the Kimbley Pit as its slope was steepened from 45° to 57°. Theoretical stress changes because of slope modification are slight except at the toe of the modified slope. Magnitudes of stress created are small when compared with the strength of a competent rock. Resulting displacement patterns point out the need for determining the in-situ state of stress at a site prior to excavation or modification. A comparison of model results with field measurements shows that, in general, the model has described the measured behavior of the west wall of the Kimbley Pit remarkably well. The Bureau of Mines and the Kennecott Copper Corp. began joint research on open-pit slope stability at the Kimbley Pit, Ely, Nev., in 1961. The initial or planning phase of this research dealt with a detailed geologic study of the Kimbley Pit, determination of in-situ stresses in the district, laboratory and field tests to determine rock properties, and the design of a full-scale experiment to study the behavior of this pit as its western wall was steepened from 45° to 57°. Fig. 1 shows a cross-section of the original pit outline, the steepened pit outline, major geologic features, and the two instrumentation adits. After the final or slope modification phase of the research began, a laboratory research program was initiated to develop a mathematical model that would analytically describe the behavior of the pit as its western slope was steepened. This theoretical model study of the slope modification at the Kimbley Pit was conducted with the finite element method of stress analysis. The results are described in this report.

Jan 1, 1969

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940