Search Documents

By F. H. Buttner, H. Udin, J. Wulff

Using a modified Udin, Shaler, and Wulff technique, the surface tension of gold Udin, purified helium was found to be 1400 ± 65 dynes per cm for the temperature range 1017° to 1042°C. IN the original Udin, Shaler, and Wulff technique for measuring the surface tension of copper: variously weighted wires were allowed to extend or contract in a copper cell held at elevated temperatures in vacuum. By plotting stress vs. strain for a wire array in one test, the stress at zero strain is obtained. This is the point where the contractile forces resulting from surface tension are balanced by the applied load, according to the expression: y = e=o r [1] where y is the surface tension in dynes per cm; a,,,, the stress at zero strain in dynes per cm; and T, the radius of the wire in cm. The assumption that the wires deform viscously permits the drawing of a straight line through the points on the stress-strain plot. Justification of the assumption has received further experimental support recently.'-' The presence of grain boundaries in the wires requires a correction to the original expression used." Thus: y = d4=T [l- (dl) (ar)Y1 [2] where, n/l is the number of grain boundaries per unit length, and a, the ratio of grain boundary tension to free surface tension. Alexander, Kuczynski, and Dawson in studying the creep of gold wire in vacuum were unable to obtain reproducible values of the surface tension of gold. In plotting stress vs. strain for progressively longer times, they found that the stress at zero strain drifted with time from positive stress values to negative values. Similarly, for the surface tension of silver, reproducible values were obtained only when a purified helium atmosphere was substituted.' Evidently the evaporation rate of silver in vacuum is too high at the temperatures employed to obtain solid-gas equilibrium even in a similar metal enclosure. Thus reproducibility of results is lost. Experimental Procedure The experimental procedure was much the same as that originally developed by Udin, Shaler, and Wulff with a few modifications and improvements. For greater accuracy in strain measurements, knots gave way to cut gage marks as shown in Fig. 1. These were made with a hand-driven lathe in which razor blades serv'ed as cutting tools. Also a more precise cathetometer with a screw accurate to 0.00015 cm was used. The tests were conducted in an atmosphere of purified .helium rather than in vacuum in order to avoid possible evaporation difficulties. Five mil wire of high purity gold (99.98 pct) was used. After cutting in the gage marks, each wire of a series of about 12 was differently loaded by welding a gold ball to one end. This was done by dipping the end of the wire in a cooling gold droplet, previously melted on a charcoal block with a No. 2 acetylene torch. The other end of the wire was strung through a hole in a gold lid and twisted over the edge to hold the wires fixed and in suspension from the lid. The lid and mounted wires were then dipped in pure ethyl alcohol to dissolve any skin oils and dirt on the surface of the wires due to handling. Finally the lid was put in place on an alundum crucible lined with gold so that the wires hung freely within the gold-lined chamber. This whole assembly was next heated in a quartz nichrome wound tube furnace and heated for a few minutes at 600°C to soften the wires. After this anneal the wires were easily straightened with tweezers. The wire assembly was finally annealed 10" to 25°C above the subsequent test temperature for 2 hr. This treatment allowed the grains to grow to equilibrium size and shape. After the anneal, the lid was mounted in front of the cathetometer. The gage length was measured by sighting the 40 power microscope on the upper lip of the lower gage mark for the first reading, then traveling up to the lower lip of the upper gage mark for the final reading. This procedure was repeated four times to give an average gage length value. In this manner the annealed gage length and the final gage length could be measured to determine the strains. During all measurements, grain counts were made.

Jan 1, 1952

By A. H. Daane, A. S. Wilson

The U-Cr system is of the simple eutectic type with some solid solubility of chromium in r and ß uranium. The eutectic occurs at 20 atomic pet Cr and melts at 859°C. The maximum solubility of chromium in y uranium is 4 atomic pet at the eutectic temperature, and in ß uranium the solubility is estimated to be 1 atomic pet. y-ß and ß-a transformations were found to occur at 737°estimatedt° and 612°C respectively. DURING 1944 and 1945, the U-Cr constitution diagram was studied in this laboratory as a part of a research program on uranium metallurgy in the Manhattan Project, and the work was described in a Manhattan Project report issued in December 1945. This paper is based on that report, which has been declassified. Prior to this study, it had been shown by other Manhattan Project workers that the low Cr-U alloys could be quenched to retain the form of uranium. Experimental The uranium used in this work was massive metal prepared in this laboratory and contained less than 0.1 pct of other elements. The chromium was 200 mesh powder obtained from the A. D. McKay Co. and was found on analysis to be 99.5 pct Cr with 0.3 pct Fe the major impurity. Alloys, weighing 400 to 600 g, were prepared by induction heating the components to 1700°C in slip-cast ZrO, crucibles in a vacuum of 3x103 mm Hg. TO prevent too violent agitation of the melt by the induction field with subsequent crucible breakage and sample loss, the ZrO2 crucible was placed in a graphite crucible, which was surrounded by a layer of powdered carbon insulation 2 to 3 cm thick. Polished vertical sections of the alloys were examined microscopically to confirm their homogeneity. Heating and cooling curves were taken on the alloys by reheating them in ZrO, crucibles to 1200°C and inserting a mullite-protected chromel-alumel thermocouple into the melt by means of a slip seal in the vacuum head of the furnace. A recording potentiometer traced the curves which had a slope of from 3" to 6" per min. Samples of the alloys were prepared for metallo-graphic examination by conventional mechanical polishing techniques followed by an electrolytic polish in an ethylene glycol-phosphoric acid-ethyl alcohol bath. The structure of the alloys was brought out clearly by this procedure so that no further etching was required. Samples for chemical analysis were taken from drillings from the top, center, and bottom sections of the alloys. The uranium was determined by titra-tion with Ce(SO1)2, while the chromium was titrated with FeSO,; the uranium and chromium totaled at least 99.6 pct in all of the alloys prepared. X-ray samples were prepared by filing bulk specimens in a helium-filled glove box and annealing the resulting powder in a zirconium-gettered helium atmosphere. A 114.6 mm diam Debye-Scherrer camera and a Weyland nonsymmetrical self-focusing camera were used with filtered copper radiation to obtain the powder X-ray diffraction data. Results The data obtained in this study have been combined to construct the constitution diagram of the U-Cr system shown in Fig. 1 where the arrests observed in cooling curves are indicated by dots. The liquidus arrest was quite distinct in thermal data taken on alloys in the range 0 to 20 atomic pct Cr. The eutectic arrest was not observed in studies on the 2.5 and 4.5 pct Cr samples but appeared in the 7.5 pct samples, which suggested some solubility of chromium in y uranium. On quenching from 859 °C, the 2.5 pct sample showed but one phase while the 4.5 pct sample contained a small amount of the eutectic along the grain boundaries; see Figs. 2 and 3. From this the maximum solubility of chromium in r uranium has been set at 4 pct. X-ray studies on these samples showed that the r phase was not retained at room temperature by quenching, but in each case a pattern was observed .which has been identified with the ß phase of uranium. Thermal data show the y-ß transformation of uranium lowered to 737°C as a consequence of this solubility. On quenching from the ß range (660°C), precipitation of chromium in the primary uranium is observed in the 2.5 and 4.5 pct Cr samples (see Figs. 4 and 5),

Jan 1, 1956

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By John F. Elliott

STAFF: Editor, Gerhard Derge Acting Editor, Poul G. Shewmon Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, PO. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Rich-ard C. Cole, President; Karl L. Fetters, Past-President; J. H. Scoff, Vice President; R. L. Henneboch, Treasurer, R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairmon; T. E. Dancy, P. R. Gouwens, W. A. Krivsky, F. C. Longenberg, E. R. Morgan, R.R. Nosh, Poul Queneou, W.O. Philbrook, J. H. Scoff, L. L. Seigle, and M. E. Wadsworth. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: M. E. Wadsworth, Chairmon; R. E. Grace, Vice Chairman; D. H. Baker, Jr., G. M. Bell, D. H. Bridges, J. M. Cigon, G. W. Healy, R. A. Lewis, C. E. O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. E. Dancy, Chairman; A. Muan, D.W. Murphy, R. D. Pehlke, J. M. Uys, J. 5. Wagstoff, and R. G. Word. lnstitute of Metals Division: R. R. Nash, Chairman, H. H. Johnson, Jr., Vice Chairman; M. R. Achter, P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. 8. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. A. Girifalco, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, R. H. Richmao, H.C.Rogers, W. Rostoker, 0. D. Sherby. E. A. Steigawald, R. Steinitz, H. C. Stumpf, R. A. Swalin, W. A. Tiller, W. R. Upthegrove, D. Walton, H.W. Weart, and D. Wilsdorf. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign;$30per $7 50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1963 by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc....Registered cable address, AlME New York . .. Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . Second class postage paid ot New York, N. Y., and Ann Arbor, Mich. Volume 227, Number 4.

Jan 1, 1963

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By W. S. McCain, B. A. Wilcox, A. H. Clauer

The creep and creep-fracture behavior of a Ni-200-2Th0, alloy has been studied over the temperature range 816° to 1038°C and stress range 4000 to 19,000 psi Specimens having their axes either parallel or transverse to the final sheet-rolling direction were tested in air, and the apparent activation energy for creep was found to be 92 kcal per mole, regardless of specinien orientation. The stress dependence 01- the steady-state creep rate, was satisfied by where n depended on orientation; n = 9.7 for rrzaterial transverse to the rolling direction and n = 24.3 for material parallel to the rolling direction. In the latter case, the relation was also valid. The rupture strength of material parallel to the rolling direction was -1.5 times gveater than the transverse rupture strength. Several tests in vacuum revealed that here the creep rate was higher and rupture life lower than for comparable tests in air. THERE is an increased interest today in producing improved dispersion-hardened alloys for high-temperature structural applications. This had led various materials designers to modify existing alloys, such as thoriated nickel. One system that has received considerable attention is based on chromium additions to Ni-ThO2, with the obvious motive of improving the oxidation resistance. Another effect of chromium is that of lowering the stacking-fault energy, y, of nickel. For example, the addition of 30 wt pct Cr decreases y from -225 erg per sq cm for pure nickel1 to -70 erg per sq cm.' This decrease in y could have several effects on the deformation behavior. There is some evidence that cross slip of dislocations around Tho2 particles is a mechanism of tensile3 and creep4 deformation in TD Nickel (Ni + 2 vol pct ThO2) at temperatures below 0.5 the absolute melting point of nickel, T,. A decrease in ? by chromium additions should increase the difficulty of cross slip. Also it has been suggested that the high-temperature (T > 0.5Tm) rate-controlling creep process in "recrystallized" Ni-Tho2 alloys is the climb of edge dislocations over Tho2 particles.5 According to weertman6 a decrease in the stacking-fault energy should decrease the dislocation climb velocity resulting in a decreased steady-state creep rate. Thus, chromium additions to recrystallized Ni-Tho2 alloys would be expected to decrease the creep rate, all other conditions being constant. However, a difficulty arises when the stacking-fault concept is applied to high-temperature creep of dispersion-strengthened metals which are produced on a commercial or semicommercial scale. This occurs because the materials are processed so that they have a high-stored energy of cold work, and the other substructural effects could obscure any influence of stacking-fault energy per se. An example of an alloy with a high stored energy of cold work is TD Nickel bar. This material has a fibrous grain structure (1 I diam by 10 to 15 p long), and the structure is stabilized by the ThO2 particles. Annealing at high temperatures, e.g., 3 hr at 1300°C, causes no recrystallization or grain growth.4 Previous work by the authors4 showed that the high -temperature creep behavior of TD Nickel could not be related to any simple dislocation theory of creep, and this probably was associated with the complex initial structure of the material.

Jan 1, 1968

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By A. Long, A. Silverman, J. L. Kulp

Garth Crosby has written an excellent geologic description of the deposits surrounding the Gem stocks in the Coeur d'Alene district. The ore deposits in the area of the Gem stocks may hold the key to the age and mineralization history of the entire Coeur d'Alene district. A recent isotopic study10 of the Coeur d'Alene district in this laboratory illustrates that a classical geologic interpretation of these deposits, with its implications for the whole district, may lead to erroneous conclusions. For this reason it seems pertinent to submit a summary of these results and an interpretation of the mineralizing history of the Coeur d'Alene districts. Pitchblende from the Sunshine mine has been dated as 1100-1200 million years (m.y.) by Kerr and Kulp,11 and Eckelmann and Kulp.12 This pitchblende is known to predate the major sulphide introduction in the Sunshine mine, but it clearly follows the metamorphism and folding of the Belt Series. Recently, Goldich (personal communication) dated sericite from the Belt rocks as 1200 m.y. by the potassium-argon method. This date establishes a minimum Belt age if the sericite is of metamorphic origin and a maximum age if detrital. The Belt Series, therefore, is not latest Precambrian. Lead isotope ratios of galenas have been measured and model ages calculated by Bate, et all3 for the Sunshine mine, Farquhar and Cummingl4 or the Bunker Hill and Sullivan mine, and Cannonl6,18 for a few other deposits in the district. Galenas from similar deposits in Southern British Columbia have been measured by Bate, et al,23 Farquhar and Gumming,11 and Wanless and Leech." The new work in this laboratory includes leads from ten widely scattered mines north and south of the Osburn fault, and through a vertical distance of over 5000 ft (Star mine). Included in this group are the Hercules, Sunset, and Mountain Goat mines, which are adjacent to the Gem stocks. In addition, galenas from stringers which cut the Gem stocks in the Success and Sunrise mines and the Hercules hanging wall dike in the lower western portion of the Hercules mine, were included in the study. All of the above leads, except one, give model ages of 1300-1400 m.y. for the time of segregation from the parent material. The concordance of the common lead and U-Pb ages, the great horizontal and vertical uniformity of the lead ratios, the sulphur ratios of two Sunshine mine galenas and three galenas from the Edith, Page, and Hercules mines indicating average crustal sulphur, and the U23/Pb204 ratio inferred for the original lead environment, indicate that the entire mineralization of the Coeur d'Alene-British Columbia base metal belt was derived from a deep source and emplaced in the Precambrian. One sample of galena from sulphide stringers cutting the North Gem stock at the Sunrise Prospect mine gave a modern (i.e., Tertiary) lead ratio. This mine is located at the northern tip of the stock. The presence of modern lead suggests mobilization of some rock lead during the intrusion of the Gem stocks and their outliers. Larsen et al.l8 have dated the Gem stocks as Tertiary by the lead alpha method. If Coeur d'Alene mineralization was genetically related to Tertiary magma formation and intrusion

Jan 1, 1961

By F. E. Streigert, J. H. Mallery, A. H. Geisler

The existing data on precipitation in Cu-Be alloys have been reconciled with some new data to present a more complete and rational analysis of the atomic rearrangements involved in the process. Two different coherent precipitates were proposed. Each is responsible for a type of diffuse X-ray diffraction effect. THE nature of the atomic rearrangement involved in the precipitation of the compound y-Cu-Be from supersaturated solid solutions of the copper-base alloys has been the subject of two extensive investigations.'-" he precipitate in this alloy system has a rather simple structure; at equilibrium it has a body-centered cubic unit cell with copper atoms on the corner sites and beryllium atoms on the center site. While a simple mechanism would be expected to obtain for the precipitation process, those which have been proposed do not adequately explain all of the reported data. The purpose of the present report is to rationalize some of the previous observations and to contribute new data on the subject obtained by the usual techniques of structure analyses. The Cu-Be system of alloys represents one of the most extensively investigated precipitation systems, so a detailed review of the pertinent literature on structure is in order. Striations: Since one of the important features of the mechanism—the habit plane—is determined by microscopic examination, microstructural features that have been observed should be considered at this time in order to assess their role in the precipitation process in Cu-Be alloys. One of the most prominent features appears as regularly oriented markings or stripings (ripples or striations) across the crystals on a suitably polished and etched sample of the aged alloy. These have been observed and interpreted by many workers. Masing and Dah14 observed striations in both the a and /3 phases of a 2.5 pct Be alloy, and attributed them to the beginning of the precipitation of very fine y crystals along favored planes of the a matrix and to the local decomposition of the £ crystals into a plus y. These markings were apparent in both the a and /3 phases of the micrographs given by Smith5 for a 2.75 pct Be alloy, while Moore" detected them in the a matrix phase using polarized light. Desch7 attributed the markings to fine precipitate particles lined up on a family of matrix planes like Masing and Dahl had done, and he identified the planes as those of the (111) family, the slip planes of the matrix. The striations were presumably the structure which Northcott- eferred to as "martensitic." He found that this structure was present in samples that had been aged under widely different conditions with hardness values ranging from 160 to 400 VHN. Later Guinier and Jacquet' also found striations in both the a matrix and secondary /3 phase. Their analyses showed that the striations were along (110) planes of the matrix phase, apparently in contradiction of the results of Desch. They found that the striations were developed during aging on the surface of a specimen that had been polished prior to aging.' On this basis they concluded that the striations represented mechanical deformation by slip along (110) planes of the matrix resulting from precipitation stresses.'" Similar but fainter striations were observed in the same manner on an A1-Cu alloy sample, in which the change in volume was much less than for Cu-Be alloys and

Jan 1, 1953

By H. C. Chao, W. F. Hosford, L. H. Van Vlack

The negative "plastic Poisson's ratio" suggested in earlier studies of Mus deformation is analyzed, and the results are verified experimentally with NaCl crystals. In the early stages of deformation where the primary {110}(110) slip predominates, compression along. the [001] direction produces contraction along the lateral [011] direction plus a compensating expansion along. the [100] direction. With additional strain, the primary slip is supplemented by secondary {111}(110) slip so that the above contraction diminishes and a more typical deformation appears. THE shape change of bee and fee crystals deformed by compression or tension along [011] has been analyzed in some detail and shown to be responsible for the development of peculiar microstructures in [011] fiber textured polycrystals of these metals.1'3 This paper concerns the unusual shape change accompanying [011] compression of NaCl crystals. It is the direct outgrowth of an earlier investigation of the deformation of manganese sulfide inclusions in steel.3,4 In that investigation, cylindrical specimens of steel containing small oriented crystals of MnS were prepared by powder metallurgy and plastically compressed. The flow of the inclusions was determined relative to that of the steel by sectioning the composite and measuring the length-to-width ratio L/W of the inclusion and diameter-to-height D/H ratio of the steel cylinder on the plane of section. These L/W ratios, normalized by dividing by the initial LO/WO ratio of the inclusion, were compared with the normalized D/H ratio of the steel cylinder. Of particular interest here are the deformation characteristics of an inclusion oriented with [Oil] parallel to the compression axis. When measurements were made on sections parallel to the (100) plane of the inclusion, the L/IV ratios were only slightly in excess of unity, indicating a high apparent hardness of the [011] criented inclusion. However, measurements on a (011) plane of section resulted in L/W ratios which were much larger, Fig. 1. These observations prompted an analysis of the strains resulting from slip in an MnS crystal compressed along [011.]. CRYSTALLOGRAPHIC ANALYSIS Manganese sulfide has the NaCl crystal structure, and the predominant slip system is {110}(110). A secondary system, {111}(110), has also been reported.= {110}(110) Slip. When a crystal is subject to a uni-axial compressive stress 011 along [011], four slip systems, (101)[101.], (101)[101.], (110)[i10], and (110) [ 110], will be equally stressed with a shear stress t = 0.2 011 while the other two {110}( 110) systems will be unstressed. The normal strain En along any reference axis n resulting from slip is given by Schmid's law: en = S COS ?in COS in ?i 111 where ?in and +in are the angles between n and the i slip direction and n and the i slip plane normal, respectively, and where ?i is the shear strain on the i slip system, For the four active slip systems above, the cos ?in cos +in terms are all equal when the reference axes are the [011] compressive axis, [011] and [ 100]. Eq. [I.] therefore reduces to en - cos ?n cos +ny [2] where y =S?i for all slip systems. Substituting the appropriate angles, Eon = 0.25? 110 eon - 0.25y110 [3] €100 = -0.50y 110 The interesting feature of Eqs. [3] is that they predict that the strains in the [011] and [011] directions, resulting from {110}(110) slip, are equal and of the same sign. Thus when a crystal is compressed along [011], it will contract along the lateral [oil] direction

Jan 1, 1967

By C. S. Matthews, M. J. Fischer

Distortions caused by dip on five-spot sweep pattern were determined by visual experiments on a model composed of parallel plates of glass with holes drilled at the well positions. This model war designed to simulate a reservoir depleted of its primary oil and containing a gas phase. Prior to interference, it was found that the injected fluid took a nearly circular shape about the injection well for the cases studied. However, these circles moved down-dip considerably under the influence of gravity. It was concluded that pattern flooding should be practical for many dipping reservoirs. A quantitative measure is given of how much the well position should be altered to allow for dip. Experimental deternzinarions of injectivity showed this to be about the same in a dipping reservoir as in a horizontal one. INTRODUCTION This investigation was undertaken at the suggestion of the Pacific Coast area, Shell Oil Co., where a pilot water flood in a dipping reservoir was being carried out at the time this paper was in preparation. Prior to the undertaking of this flood there had been considerable speculation as to how gravity would distort a flood pattern in a dipping reservoir. The thought was expressed in some quarters that a five-spot flood would not be applicable to a dipping reservoir because the flood pattern would elongate in the direction of dip and would never form a "seal" around each five-spot. If the flood pattern elongated sufficiently, both the oil and the water might flow largely downdip rather than into the pattern producers. In view of the importance of the California water floods, it was deemed important to determine the effects of gravity on a five-spot pattern in a dipping reservoir. Previous work had also been carried out in this laboratory,1 but only for the single-fluid case. The present investigation extends these results to multifluid cases. Several sets of pictures of flood fronts are presented so that the process can be visualized. From these pictures, curves are obtained which show the correct drilling position for achieving equal times of oil-bank breakthrough. Several injectivity curves are also presented which may aid in prediction of injection rate. ASSUMPTIONS The present results were obtained with a model composed of two parallel plates of glass spaced about 1 mm apart. When the inertial forces are small, as in these experiments, the flow between the plates follows Darcy's law and is analogous to flow through porous media. In using these plates, it is not possible to scale effects of capillarity correctly as regards a transition zone between injected and displaced fluid. Calculations show, however, that effects of such capillarity should not be important in determining the gross flooding pattern in the field. In fact, in this model the capillary forces tend to circularize the pattern to a greater degree than in the field. To preserve a large ratio between the viscous forces and the circularizing capillary forces in the laboratory model, viswus glycerine was used as the flooding liquid and the rate of flooding was very high. The circularizing force is believed negligible in these experiments. In addition to the effect of the surface tension y, which tends to circularize the pattern, another capillary force must be considered. This is the adhesion tension y cos, which acts at right angles to the circularizing term y. If the plates in the model are "wetted" the same all around the periphery, then the adhesion tension,

Jan 1, 1957

By James Terry Duce

The symposium on production for the year 1941 contains few papers on the foreign situation. Rigid censorship prevails in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even truer than in the last war, owing to greater mechanization of armies. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to AutHORs In order to facilitate interpretation of the data in this chapter, we print the fol-lowing excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir.. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1942

By James Terry Duce

The symposium on production for the year 1941 contains few papers on the foreign situation. Rigid censorship prevails in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even truer than in the last war, owing to greater mechanization of armies. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to AutHORs In order to facilitate interpretation of the data in this chapter, we print the fol-lowing excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir.. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1942

By E. T. Turkdogan, L. S. Darken

Using the quadratic formalism, thermodynamic equations are derived for the composition dependence of the heat and entropy of mixing. The applicability of these equations is confirmed by available experimental data on the activities and heats of mixing for binary metallic systems of Group ZZB elements. In a recent paper arkeen' introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. That is, in the terminal region, which may extend to as much as 60 at. pct, the logarithm of the activity coefficient, log y,, of component 2 is a linear function of (1 - N,)' where N2 is the atom fraction of component 2. Similarly, for the other component, log yl is a linear function of (1 - N,)'. A number of iron-base binary liquid alloys were shown to obey this quadratic formalism. arkeen' extended this formalism also to any corner of a ternary system and showed that the activity coefficients of the components 1, 2 and 3 (1 is taken as the solvent) can be represented by quadratic terms involving five parameters, four of the binaries and one for the ternary system. Numerous examples given by arkeen' demonstrated the general applicability of the quadratic formalism to iron-base systems over a wide composition range. In this paper further examples are given of binary liquid systems (Group IIB elements, Zn, Cd, and Hg) and of several solid solutions, again demonstrating the appropriateness of this concept. A further purpose of this paper is to extend the quadratic formalism to the enthalpy and excess entropy of binary metallic solutions and to test the equations so found using available experimental data. QUADRATIC FORMALISM FOR HEATS AND ENTROPIES OF MIXING OF BINARY METALLIC SOLUTIONS The following equations, reproduced from Darken's paper, are for the two terminal regions of binary systems. at infinite dilution and a's are temperature dependent parameters to be determined from the experimental data. Although the quadratic formalism is an assumed representation of the data, Eqs. [I] to [4] are thermo-dynamically consistent with the Gibbs-Duhem relation and satisfy Raoult's and Henry's laws as limiting cases. As pointed out previously,' the following form of the Gibbs-Duhem equation facilitates the integration in general but particularly in regions I and 11, where each of the derivatives is constant. The partial molar enthalpy of solution i, (and i; the value of i, at infinite dilution) are related to the activity coefficients y, and y," by the thermodynamic relation Differentiating Eq. [l ] with respect to 1/T and substituting the above thermodynamic relation gives for region (I) It is reasonable to assume that over a temperature range of experimental interest, the enthalpy of mixing is essentially independent of temperature, implying from Eq. [7] that the derivative da,,/d(l/) is also independent of temperature. On the basis of this argument, the temperature dependence of a has the form where £ and S have the units of enthalpy and entropy respectively; they are characteristic parameters for a terminal region of a binary system, e.g. for region (I), C12, S12 and for region (II), d:,,, S2,. Using this equation gives for dff ,/ d(l/), From Eqs. [7] and [9] an expre_ssion is obtained for the composition dependence of L,. Similar calculations are made for El and the results are summarized below for the two terminal regions. For region (I), The corresponding expressions for the molar heat of solution, AHM, are readily obtained from the above equations for the two terminal regions: For region (I),

Jan 1, 1969

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Klaus Schwerdtfeger

In order to test the performance of ZrO, (CaO) and Tho,(Yz03) electrolytes in the electrochemical determination of oxygen activities in liquid metals at steel-rrzakitng temperatures , electromotive force measurements have been made with the following cells: The oxygen-- activities are calculated from the electmrnotive forces for the investigated systems. The standard free energy of- formation of MnO and the activity of manganese in Fe-Mn melts are derived. Indications are that the Zr 0z(Ca0) electrolyte exhibits little electronic conductivity at oxygen pressures as low as 10'a atnz at 1600°C; however, the partial electronic conductivity may become noticeable at lower oxygen activities. The Tho,(Yz03) electrolyte is found to be an ionic conductor at the oxygen pressure as low as that for the Mn + MnO equilibrium, but exhibits partial electronic conductivity at oxygen pressures higher than 10"1 atm (1500°C). fi. better control of oxidation and deoxidation reactions in steelmaking may be facilitated if the oxygen activity in the steel is known during various stages of the process. In the present work oxygen activities have been measured in liquid iron, manganese, and iron alloys with galvanic cells using ZrOz(CaO) and s solid electrolytes with the object of establishing the range of oxygen pressure in which these materials can be used as electrolytes at steelmaking temperatures. Calcia-stabilized zirconia and Tho2-Y203 solid solutions are oxygen ion conductors. Such electrolytes were first used by Kiukkola and Wagner1 and Peters and ~ann' in galvanic cells for the determination of thermodynamicquantities of oxide systems in the temperature range 700" to 1200°C. At these moderate temperatures calcia-stabilized zirconia has been found to exhibit predominantly ionic conductivity at oxygen pressures as low as those for the Cr + Crz03 equilibrium,394 but at lower oxygen pressures elec- tronic contribution to conductivity becomes significants4 The Th02-Y203 solid solutions are ionic conductors at oxygen pressures lower than those applicable to zirconia base electrolytes.5'6 At high oxygen pressures Thoz base electrolytes exhibit significant p-type semiconduction. At the time the present experiments were carried out several papers1'-* were published on the electrochemical determination of oxygen activities in liquid iron using the ZrOz(CaO) electrolyte. The results of different authors do not agree well. For instance, according to Fischer and ~ckermann" stabilized zirconia can be used to measure oxygen contents in liquid iron larger than 0.02 wt pct, but according to Baker and west1' ZrOz(CaO) cannot be used for the determination of oxygen content in liquid iron because of high electronic contribution to the conductivity. Fig. 1 is a schematic diagram of the apparatus used. About 500 g of liquid metal is contained in a crucible into which a stabilized zirconia or Th02(Y203) tube is immersed. A platinum contact wire is pressed (with a spring mechanism) against the inside bottom wall of the electrolyte tube. The tube is flushed continuously with a stream of air, CO-CO, (or Hz-C02) (at 0.96 atm and at a rate of about 300 cu cm per min), via an alumina tube inserted inside the electrolyte tube. This alumina tube also contains the Pt-Pt/10 pct Rh thermocouple. A capillary alumina tube shielding the other contact wire is immersed in the melt. The molybdenum contact wires were used mostly; in some cases platinum wire was employed. Molybdenum has the advantage that it dissolves more slowly in the melt than platinum. The whole cell was contained in the alumina reaction tube of a resistance furnace with molybdenum winding. The reaction tube was closed gas tight at both ends and flushed continuously with argon. Because of the poor thermal shock resistance of the electrolyte tubes the cell had to be assembled in the cold furnace. The electrolyte tube and alumina sheath

Jan 1, 1968