Search Documents

By R. W. Fountain, M. Korchynsky

The precipitation phenomena occurring in cobalt-tantalum alloys have been investigated in the temperature range frm 500" to 1050°C by correlating the results of metallographic, X-ray, micro-and macrohardness, and electrical resistivity studies. The property andmacrohardness,changes were found to depend on 1) general precipitation, and 2) lamellar precipitation. Two new intermetallic phases have been identified: 1) a Co3Ta, a metastable ordered face-centered-cubic compound, and 2) a stable ß Co3Ta phase of hexagonal structure. In addition, the previously reported Co2Ta phase was found to exist in two allotropic modifications: the hexagonal MgZn,-type and the cubic MgCu2-type Laves phases. SINCE a large variety of structures can result as a consequence of the decomposition of a solid solution, predictions on the nature of property changes are difficult, if not impossible, to make. For any rational attempt to correlate properties and structures of a precipitation-hardenable alloy, a detailed understanding of the kinetics of decomposition and morphology of phase separation, as well as knowledge of phase relationships, appears to be prerequisite. Information of this type has been accumulated in the past for many alloy systems, both of theoretical and pastforpractical importance.1,2 Although the presence of intermetallic compounds has been reported in cobalt-base alloys,3 the amount of published information on precipitation-hardenable cobalt-base systems is very limited. A survey of the binary phase diagrams of cobalt indicates that cobalt-tantalum alloys might be of interest as typical of other cobalt-base systems in which Laves phases of the A,B type can be precipitated from solid solution. The present work has been undertaken, therefore, to study the kinetics and morphology of the precipitation reaction in this system and to establish a base for a correlation between the structural aspects and properties in this class of alloys. PREVIOUS WORK The only available phase diagram of the cobalt-tantalum system is based on the work of Koster and Mulfinger. According to these authors, the maximum solubility of tantalum in cobalt is about 13 pct (at 1275°C) and. less than 7 pct at room temperature. Tantalum additions lower the temperature of allotropic transformation of cobalt (about 420°C), and at 7 pct Ta, the high-temperature face-centered-cubic modification (ß cobalt) is retained at room temperature. The precipitating phase was originally designated as Co5Ta2 compound (55.2 pct Ta, about 1550°C melting point), but subsequent investigations by wallbaum5" identified this constituent as the A,B-type Laves phase. Wallbaum's data indicate that there are two modifications of this intermetallic compound: one richer in cobalt (Co2.2 Tao.8)of the hexagonal MgNi, type; and another of a higher tantalum content (Co2Ta) of the cubic MgCu, type. On the other hand, Elliott7 found that the cobalt-rich alloy (CO2.10,Tao.~l) was predominantly the cubic MgCu, type at 800°C and a mixture of both the MgCu2 and the hexagonal MgZn,-type Laves phases at 1000°C. At 1200°C, Elliott found only the MgZn, type while at 1400°C, he observed only the MgCu2 type. At the stoichiometric composition, Co2Ta, Elliott reported only the cubic MgCu2-type Laves phase in the temperature range of 600oto 1600°C. The precipitation of the cobalt-tantalum intermetallic compound is accompanied by a marked increase in hardness. According to Koster's4 data, the Brinell hardness of an 8 pct Ta-Co alloy increases from 230 to 340 upon short-time aging at 800°C. EXPERIMENTAL PROCEDURE The binary cobalt-tantalum alloys investigated contained 5, 10, and 15 pct Ta. The range of tantalum additions was thus slightly broader than the reported minimum and maximum solid solubility limits of tantalum in cobalt (7 and 13 pct, respectively)4 The alloys were vacuum-induction melted in a magnesia crucible using cobalt rondelles and technically pure tantalum sheet as raw materials. Deoxidation of the melt was accomplished with carbon, and the chemical analysis of the alloys is given in Table I. The effect of isothermal aging treatments on the progress of precipitation was studied on samples cut from cast ingots. These samples were solution treated for 2 hr at 1250°C and water-quenched. Aging was conducted in the temperature range from 500" to 1050°C for periods between 15 min and 1000 hr and followed by water-quenching. To prevent contamination from the atmosphere, all samples were sealed in evacuated Vycor or quartz tubes for heat-treatments. For solution treatment, argon at 0.2 atmospheric pressure was introduced prior to sealing of the capsule to prevent collapse at high temperature, and titanium sponge was placed at one end of the capsule to act as a getter. MACROHARDNESS The effect of aging on Vickers hardness (Dph) of

Jan 1, 1960

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

By Reno H. Sales

Jan 1, 1914

By E. Motica

Ores containing uranium and vanadium minerals have been mined from the Salt Wash Member of the Morrison Formation from many localities in the Colorado Plateau region since about 1900. The most productive deposits are in a relatively small area in Southwestern Colorado referred to as the Uravan mineral belt. The mineral belt is a narrow elongate area in which uranium-vanadium deposits in the Salt Wash have a closer spacing, larger size, and higher grade than those in adjoining areas. Pre- 1948 ore production from the mineral belt was 655,000 tons averaging 1.91 per cent V2O5 and 0.28 per cent U3O8. Production during the 1948 to 1964 period was 7,900,000 tons of ore averaging 1.46 per cent V2O5 and 0.27 per cent U3O8. The ore deposits occur principally in the uppermost sandstone unit of the Salt Wash. This unit consists of sandstone lenses formed by a system of aggrading braided streams flowing in an easterly direction generally normal to the mineral belt. These lenses, referred to as channels, are as much as one mile in width and average about 50 feet in thickness and can be traced for several miles along their courses. Areas favorable for one deposits are recognized principally by the following criteria: ( 1) a host sandstone thickness of over 30 feet, (2) the presence of carbonaceous material in the host sandstone, and ( 3) gray mudstones and clays associated with the ore-bearing sandstone. The ore minerals are believed to have been precipitated from laterally migrating solutions; there is no apparent genetic relationship between ore deposits and tectonic structural features. Exploratory and development drilling from the surface is conducted in three phases: first, wide-spaced drilling to find and outline favorable channels; second, moderate-spaced drilling in favorable ground to locate ore deposits; and third, close-spaced drilling to block-out ore. Long-hole drilling from underground stations is used to find and delineate extensions of ore bodies being mined. Due to intense production since 1948 from shallow deposits, best potential for new deposits exists in areas where the ore-bearing unit is 600 to 800 feet deep.

Jan 1, 1968

By S. E. Maddigan, B. R. Zimmerman

MOST metallurgists are well acquainted with the contributions already made to the study of metals by the use of X-rays. On the one hand, the radiographic method is constantly becoming of increasing importance as a nondestructive testing procedure, while on the other hand the techniques of X-ray diffraction have made important contributions to the fundamental knowledge in studies of phase diagrams, stress conditions, and so forth. A new, and as yet insufficiently appreciated, tool exists in the application of microradiography to alloy structures. This new procedure in many respects bears the same relation to microscopic investigations as does macroradiography to the gross inspection of metal surfaces. However, where macroradiography is used ordinarily to determine the soundness of the metal structure, this new method can be used not only to investigate micro-un- soundness but also to examine the distribution of the constituent elements within the body of the alloy. When combined with the normal procedures of microscopy, this offers a technique of great potential power. It is intended in this paper to present a few examples of copper-base alloys demonstrating the additional knowledge obtained from the microradiographic method. The detection of micro-unsoundness is demonstrated in Fig. I for a sample of cartridge brass as cast. The sample appeared quite sound when viewed under the microscope, but in reality was thickly populated with minute voids. This application of the method conforms in every way to conventional large-scale radiography and has been used to facilitate production of metal for vacuum devices.1 The true potentialities of the technique are revealed by comparison of Figs. 2a and 2b, which are respectively a- photomicrograph and a microradiograph of a cast alloy of 80 per cent Cu, 10 per cent Sn, 10 per cent Pb. The remarkable difference in appearance provides some concept of the additional information this method may yield when used as an auxiliary to microscopic studies. Fig. 2a shows two phases of the copper-tin system plus segregated lumps of lead. Fig. ab, on the other hand, shows with exceptional clarity the actual dendritic growth of the metal crystals during solidification. The practice of microradiography depends upon the laws of absorption of X-rays. This subject has been reviewed thoroughly in recent papers,1,2,3 but for clarity a brief resumé will be given here. As is well known, when a beam of X-rays is transmitted through a layer of homogeneous material, the intensity is reduced according to the relation:[ ]

Jan 1, 1944

By E. A. Anderson

THIS seems to be the year for superlatives in A.I.M.E. meetings. The programs of the various Divisions and Institute committees offered an abundance of interesting and valuable information in the form of technical papers, symposia. and lectures to large and interested audiences. The Institute of Metals Division may hold up its head with pride for its own program. With six technical sessions, three full-day symposia, and the annual I.M.D. dinner, four meeting days were not enough and many simultaneous sessions were required. The quantity and quality of the paper were equaled by the numbers and interest of those attending.

Jan 1, 1944

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By G. D. Cremer, J. J. Cordiano

ALUMINUM powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, how- ever, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and aluminum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. 4 second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age- hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders, is probably the significant factor in our failure to obtain strong sintered pieces. METHODS OF PRODUCING THE POWER Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By R. S. Archer

THE PROPER representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem. The complete solution of the problem will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the A1 point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A 1 point is an open question, but that complete graphitization (to less than 0.10 per cent. combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440° F. It is the

Jan 2, 1920

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By W. A. Clark, E. H. Dresser

ORE from the Minnesota iron ranges is transported from the mines to the loading docks on Lake Superior over four different railways: the Great Northern, Northern Pacific, Soo Line, and Duluth, Missabe and Iron Range, with hauls varying from 60 to 110 miles. For this service a large amount of specialized equipment is used. The steel ore cars are of the hopper type, 24 ft. long, to dump into alternate pockets of the docks, these pockets being 12 ft. long to correspond with the 12 or 24-ft. spacing of the boat hatches. The more recently con-

Jan 1, 1941

By H. J. Ramey

The wellbore acts as a storage tank during drawdown and build-up testing and causes the sand-face flow rate to approach the constant surface flow rate as a function of time. This effect is compounded if non-Darcy flow (turbulent flow) exists near a gas wellbore. Non-Darcy flow can be interpreted as a flow-rate dependent skin effect. A method for determining the non-Darcy flow constant using this concept and the usual skin effect equation is described. Field tests of this method have identified several cases where non-Darcy flow was severe enough that gas wells in a fractured region appeared to be moderately damaged. The combination of wellbore storage and non-Darcy flow can result in erroneous estimates of formation flow capacity for short-time gas well tests. Fortunately, the presence of the wellbore storage eflect permits a new analysis which can provide a reasonable estimate of formation flow capacity and the non-Darcy flow constant from a single short-time test. The basis of the Gladfelter, Tracy and Wilsey correction for wellbore storage in pressure build-up was investigated. Results led to extension of the method to drawdown testing. If non-Darcy flow is not important, the method can be used to correct short-time gas well drawdown or build-up data. A method for estimation of the duration of wellbore storage effects was developed. INTRODUCTION In 1953, van Everdingen and Hurst generalized results published in their previous paper3 concerning wellbore storage effects to include a "skin effect", or a region of altered permeability adjacent to the wellbore. Later, Gladfelter. Tracy and Wilsey4 presented a method for correcting observed oilwell pressure build-up data for wellbore storage in the presence of a skin effect. The method depended upon measuring the change in the fluid storage in the wellbore by measuring the rise in liquid level. To the author's knowledge, application of the Gladfelter, Tracy and Wilsey storage correction to gas-well build-up has not been discussed in the literature. It is, however, a rather obvious application. Gas storage in the wellbore is a conlpressibility effect and can be estimated easily from the measured wellbore pressure as a function of time. Several approaches to the wellbore storage problem have been suggested. As summarized by Matthews, it is possible to minimize annulus storage volume by using a packer, and to obtain a near sand-face shut-in by use of down-hole tubing plug devices. Matthews and Perrine have suggested criteiia for determining the time when storage effects become negligible. In 1962, Swift and Kiel' presented a method for determination of the effect of non-Darcy flow (often called turbulent flow) upon gas-well behavior. This paper provided a theoretical basis for peculiar gas-well behavior described previously by Smith. Recently, Carter, Miller and Riley observed disagreement among flow capacity k,,h data determined from gas-well drawdown tests conducted at different flow rates for short periods of time (less than six hours flowing time). In the original preprint of their paper, Carter et al. proposed that the discrepancy in flow capacity was possibly a result of wellbore storage effects. Results of an analytical study of unloading of the wellbore and non-Darcy flow were recorded by carter.14 In the final text of their paper, Carter et al.!' stated that they no longer believed wellbore storage was the reason for discrepancy in their kgh estimates. In view of the preceding, this study was performed to establish the importance of non-Darcy flow and well-bore storage for gas-well testing. In the course of the study. a reinspection of the previous work by van Everdingen' and Hurst' was made, and the basis for the Gladfelter, Tracy and Wilsey' wellbore storage correction was investigated and extended to flow testing. WELLBORE STORAGE THEORY As has been shown by Aronofsky and Jenkins,11-12 Matthews," and others, flow of gas can often be approximated by an equivalent liquid flow system. The following developnlent will use liquid flow nomenclature to simplify the presentation. Application to gas-well cases will be illustrated later. First, we will use the van Everdingen-HursP treatment of wellbore storage in transient flow to establish (1) the duration of wellbore storage effects, and (2) a method to correct flow data for wellbore storage. DURATION OF WELLHORE STORAGE EFFECTS When an oil well is opened to flow. the bottom-hole pressure drops and causes a resulting drop in the liquid level in the annulus. If V. represents the annular volume in cu ft/ft of depth, and p represents the average density of the fluid in the wellbore, the volume of fluid at reservoir conditions produced from the annulus per unit bottom-hole pressure drop is approximately: res bbl-- (V, cu ft/ft) (144 sqin./sq ft) psi -(5.615 cu ft/bbl)(pIb/cuft) ........(I)

Jan 1, 1966

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By I. M. Roberts

THE war emergency has affected every phase of industry. The gas and coke-oven companies have sought faithfully to discharge their responsibility in this critical period and have willingly modified their operations where possible to meet the ever increasing demands made upon them. Our company made commitments for blast-furnace coke for war purposes which necessitated a reduction in coking time in order to produce the amount required to. meet the new demands. At the same time there were certain customers of long standing, who had been supplied with foundry and egg-sized coke produced on fairly long coking periods, who also were engaged in war work and whose patronage we desired to retain. Coke produced on short coking rates from the coal mixture we were then using would not have been satisfactory for these customers. The average width of our ovens is 19 ¾ in., which is a little wider than the more modern ovens of the present day. They were originally designed to give somewhat cool tops in order to produce a rich gas. This necessitates carrying the heats a little on the warm side so that the tops will be fully carbonized. A reduction in coking time, as is generally known, is accompanied by a reduction in the average size of the coke produced. This is due to the greater shrinkage that takes place at the higher temperatures required to carbonize the charges in a shorter time. The net result is that the coke is more cross fractured and longitudinally fractured and breaks up into small sizes on handling. The cokes produced from the better coking coals seem to be more susceptible to fracture at high temperatures than those from poorer coking coals. A coal mixture that produces a beautiful foundry-sized coke at 30 to 36 hr. may yield a product at 18 hr. that would be so badly fractured as to be unsatisfactory for foundry practice. COKING CHARACTERISTICS OF COALS Our problem was to find some economical innovation and develop a method that would enable us to reduce the coking time and still produce a coke satisfactory to our foundry trade. However, before discussing the results of our present operations, it might be well to present a few observations on the coking characteristics of coals in general. Most coke-oven operators carbonize a blended mixture of coals. It may consist of a single high-volatile coal with a single low-volatile coal, or of a combination of several high-volatile and low-volatile coals. Medium-volatile coals of the Eagle seam are used for the production of high-grade foundry coke. Medium and high-volatile coals are often blended with one or more low-volatile coals. The possibilities are almost infinite, but the combinations are limited by such factors as cost and facilities for handling multicoal mixtures, and by other practical considerations. Every coal has characteristics that make it blend better with a particular coal or coals in preference to others. This property has

Jan 1, 1944

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

By T. V. Moore

DURING 1910, crude-oil production in the United States reached a record level averaging about 3.700,000 barrels daily. Export declined sharply while imports increased with the result that large quantities of crude oil were run to storage during the year. Imports consisted largely of residual fuel oil brought in from South America bit because of a shortage of that product in this country and of Mexican crude. The price of petroleum products followed the declining trend of the last three year resulting in serious disparity between crude and product prices. This condition was aggravated in some areas by the increasing production of distillate by recycling operations and by the high tanker rates prevalent in the last two months of the year. As a result two small purchasers found it necessary to reduce crude-oil price in the Corpus Christie area of Texas.

Jan 1, 1941

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer's function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don't know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By Wilbur E. Sanders

AT some period during the operation of metalliferous and other commercially valuable mineral-deposits in connection with their underground mining, when the developments therein have become so extensive that their description is tedious and confusing, some scheme for naming or numbering the various workings and their parts is necessary for convenience of ; reference.. A simple and symmetrical yet expansive system of classification must be devised, one that is capable of being extended to cover all possible exigencies and conditions of future operations within the property. Such a scheme, properly arranged, greatly simplifies communication between the various departments of the mining business, as, for instance, between the administrative and the operating departments of the concern, and is of the greatest assistance to the officers of the mine in enabling them to locate and describe particular points and parts of workings and specific kinds of work. Again, in the proper segregation and differentiation of mine-accounts, when they are carried out with that detail which will furnish ready information concerning the cost of a particular piece of work, or the various items and totals of expense connected with the, development,, operation and repair of each or all of the mine-workings, some such method of designation becomes a necessity. . Moreover, such a plan is admirably adapted to the needs of the mining engineer, who, in connection with his reports upon mining-properties, is sometimes required, in his descriptions of certain blocks of ore, to locate lists of assays of samples taken from many and various places, and to designate workings and parts of workings that are located in different parts of the mine, sometimes at points wide apart.

May 1, 1906