Search Documents

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By D. C. Porterfield

ProUuction of crude oil in Venezuela increased from 186,134,000 bbl. in 1940 to 2~8,131,ooo bbl. in 1941, or 22.6 per cent, to establish a new all-time high for the country. While the average production for the year was 625,000 bbl. per day, production during the month of December 1941 averaged 751,000 bbl. per day, and during the last week of the year, 766,000 bbl. per day. Production from the Lake Maracaibo basin averaged 454,000 bbl. per day during the year, or 72 per cent of the total for the country, compared with 73 per cent of the total produced in 1940. Drilling during the year was approximately on the same scale as in 1940, with 438 wells completed in 1941 as compared with 429 the year before. Exploratory completions decreased from 18 in 1940 to 6 in 1941. Of the drilling operations in 1941, 56 per cent was concentrated in the Lake Maracaibo basin and 44 per cent in eastern Venezuela, success being 98 per cent in the Lake basin and 83 per cent in the east. Successful completions for the country as a whole amounted to 92 per cent of the total wells drilled. Exploratory drilling in 1941 resulted in the discovery of three new fields, all in eastern Venezuela; viz., Guara, about II km. to the northeast of the Oficina field but on a separate structure; Santa Rosa, which is east of El Roble field on a structure forming a part of the major Santa -Ana- San Joaquin-El Roble uplift; and Santa Barbara, which is southwest of the Jusepin field on an extension of the main Jusepin anticline. At the close of the year three wildcats were drilling, all of which showed prospects of obtaining production; that is, Mercedes No, 2 in central Guarico, Las Ollas No. I on the Anzoategui-Guarico border near the town of Zaraza, and Quiamare No. I in Anzoategui northeast of the town of San Mateo. In spite of heavy withdrawals and the resultant natural decline in the potentials of older producing areas, new drilling during the year increased the potential production of the country from an estimated 780,000 bbl. per day at the end of 1940 to an estimated 810,000 bbl. per day at the end of 1941, or approximately 4 per cent. Since domestic consumption of petroleum products is insignificant compared with total production, exports of crude and products during the year increased in line with production. Crude exports totaled 196,800,000 bbl., compared with 158,400,-000 bbl. in 1940, and exports of products were 26,100,000 bbl., compared with 21,900,000 bbl. the year before. Exports of crude from Venezuela to the United States amounted to 36,500,000 bbl. In addition, about 2,200,000 bbl. was imported in bond into the United States for transfer to Canada. Total refining capacity of the country in 1941 was approximately 125,000 bbl. per day, including a crude-conversion plant with a capacity of 32,000 bbl. per day, capable of making fuel oil only. Three plants with a capacity of 121,000 bbl. Per

Jan 1, 1945

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of by- product materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals.

Jan 1, 1949

By WILFRED SYKES

THE story of the rolling of strip steel is not limited to any one plant or individual or group of individuals. It is a story with many ramifications. First of all, it should be understood that the strip mills we are considering are continuous mills, in that the steel passes directly from one mill to the other in a more or less straight line. Continuous mills are not new; in fact, they have been used for many years in the rolling of a few simple shapes. They were, however, driven by one motor through jackshafts, and as a result the speed of each roll stand had a fixed relation to that of every other stand in the series. This in turn fixed the reduction that could be made in each stand. The mill could produce simple things, but was not satisfactory for the production of the variety of strip now required. It was, therefore, necessary to get away from the restrictions of that kind of drive. To accomplish this, the designer could either separate

Jan 1, 1936

By P. BOURY

THIS account of a contrivance which has been found serviceable in practice may be of interest to engineers, and' especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects, namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle. This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Sep 1, 1906

By Charles E. Weaver

During the past few years there has been considerable activity in prospecting for oil and gas in several parts of western washington. From time to time seepages of oil or emanations of gas have been reported from various places. Several companies have been organized for the purpose of drilling, but only a part of these have actually begun operations. In certain localities very small seepages of oil occur, but up to the present time no oil or gas in commercial quantities has been obtained. In order to determine the conditions which may be favorable or unfavorable to the occurrence of petroleum it becomes necessary to know the character and extent of the geological formations in which such deposits might occur. In other regions where producing wells have been developed it is possible to know what formations contain the oil and what structural conditions influence its concentration in reservoirs or zones. It is usually possible to determine those strata which contained the materials from which the petroleum may have been derived and also the position and distribution of the more porous sandstone belts into which it may have collected. Detailed stratigraphic surveys may even determine the depth at which a certain known oil-bearing zone may be tapped at any particular place. It is also possible to recognize those formations which are presumably barren of oil, as well as those which are absolutely so. In new regions far distant from any of those which are now producing or have produced in the past, it becomes absolutely impossible to foretell whether oil may exist in commercial quantities or not. Assuming that such deposits do exist, it is extremely difficult to predict at what depth the produciqg zone or zones occur. However, in prospecting in a new and unexplored region, use should be made of such laws as have been found to govern the occurrence of petroleum deposits in other well-developed fields. Such deposits in their world-wide distribution are found almost exclusively associated with sedimentary rocks. Areas composed predominatingly of igneous and metamorphosed rocks are to be rcgarded as extremely unfavorable localities for the occurrence of commercial deposits of oil or gas. Assuming that such oil deposits are

Jan 1, 1916

By C. C. CONCANNON

POTASH is an essential. It is necessary as an ingredient in fertilizers or as a plant food, and certainly one of the great problems, and one of increasing gravity, is the maintenance of agricultural fertility that we may have adequate food supplies. When one thinks of potash one thinks of Germany. The first and most important deposits of soluble potash salts were found in Germany, and it was through Ger- man research and the application of a highly developed knowledge of chemistry that the value of these deposits was recognized and appreciated in the field of agricultural fertilization. The Germans knew that they had something of great value in their potash resources, not only because of the advantage derived from the extensive use of it in their own intensive farming operations at home, but also because of the pressing need for it on the part of other countries. Appreciating the economic value of this in international trade, they fostered the industry to the fullest extent and devoted much attention to well organized propaganda designed to bring out the essential need for potash of German origin throughout the world. Thus every one came to believe that potash was an essential commodity of only German origin and as such it held an extraordinary position in world trade prior to 1914.

Jan 1, 1926

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By D. V. Carter, Dan C. Williams, John R. Coombs

Exploration was active in East and East Central Texas during 1944. Ten oil fields were discovered during the year, of which four show promise of development. The discovery wells of the Sand Flat and Tyler, South fields were drilled to a depth greater than 10,000 ft., and the latter field now produces from the Pettit at a depth of 9890 ft. The Sand Flat well was plugged back to the Paluxy. The other two fields are Glen Rose producers near 8000 ft. The Pickton field produces from the Bacon Lime and Winnsboro from the Rodessa section. The Eylau field, Bowie County, was significant as the first Smackover production in Texas. Magnolia drilled a test in the Concord field, which topped salt. The most extensive and significant development in the district was the Carthage gas-condensate field. It expanded from the 8000 acres of last year to an estimated 190,000 acres, or about 300 sq. miles, and is not defined as yet. The first oil production in the Carthage area was made from the Travis Peak in 1944 in the Rogers Lacy's Cameron Lumber Company well No. I, on the northwestern side of the field. The New Hope field, Franklin County, scored the largest number of completions during 1944 with 24, bringing its total number of wells to 27. Two more pays were opened and produced as dual completions with the older horizons. The Manziel field, Wood County, had 19 new wells added during the year, for a total of 29, while the Pittsburgh field, Camp County, reached a total of 23 wells by completing 14 new ones. Material shortages and drilling restrictions dropped the total number of producing wells completed in the district from 171 during 1943 to 141 for 1944. Abandonments increased from 531 during 1943 to 609 for 1944. Of this number, 479 were in the East Texas field. Subsidy payments had very little effect in the district and it was mostly a few of the old fault-line fields that had any wells to fall within the requirements for subsidy payments. The prices of crude oil remained constant in the district except for increases as a result of subsidy payments. Production and Probation Wartime demands called for increased allowables for many fields, consequently the condensate and oil production for 1944 increased to 190,016,180, which is up 6.9 per cent over 1943. The East Texas field, of course, remained the principal producer of the district, accounting for 134,768'499 bbl. during the year, or 71 per cent of the district total production of condensate and oil. The field topped its own 1943 production by 4.8 per cent and became the first field in the world to produce 2 billion barrels of oil. The Hawkins field remained the second largest oil producer in the district, with 13,317,088 bbl. for the year, a drop of 6.8 per cent from 1943, while Van field was third with 11,635,708 bbl. The

Jan 1, 1945

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943

By W. L. Zeigler

DURING the middle 1880s, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddies. Later Wilfley tables took the place of sand jigs and vanners superseded the buddies. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. TAILINGS DISCHARGED INTO STREAMS From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1947

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955