Search Documents

By Glenn C. South, Charles C. Russell

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By William Plank

IN PAST YEARS, engineering educators and others have been able to study the problems relating to en-gineering education in the United States with only inadequate and, frequently, inaccurate data at their command. For the first time there is now available fairly full and accurate information on this subject, gathered and compiled by the Board of Investigation and Coordination of the Society for the Promotion of Engineering Education. This board, of which W. E. Wickenden is the director, has for the past four years been carrying out fact-finding investigations into "the objects of engineering education and the fitness of the present day curriculum," under a grant of funds from the Carnegie Corporation of New York. Twelve bulle-tins have already been published by the board and others are in the process of preparation. The studies made, thus far, have been of the various phases of engineering education in general as well as of the major branches of engineering. Within the past year. the board has completed a study of mining engi-neering education by means of a questionnaire sent to members of the Institute. A special committee, con-sisting of Charles E. Locke, Allen H. Rogers and the writer, cooperated with the board in drafting certain parts of the questionnaire and in selecting the mailing list. Similar studies have been made through the mem-bers of the four other national societies. The results of these studies have been published only in mimeo-graphed form, therefore, in order to place the data before the members of the Institute an incomplete sum-mary of the replies to the A. I. M. E. questionnaire is here given. The full report will be available for distri-bution at the annual meeting in February. The questionnaire was sent to 306 members of the Institute, a proportion about equal to the proportion of the membership of the other national societies can-vassed; 152 members replied to the questionnaire, 55 per cent of whom had received college degrees in some branch of engineering connected with the mineral in-dustry. Forty-seven educational institutions were rep-resented in the replies. Seventeen different positions were held by the members who replied, with 24 con-sulting engineers at the head of the list, 20 managers, 16 superintendents, 11 presidents, 10 professors, 6 deans, and others.

Jan 1, 1928

By H. Herbert Hughes

ECONOMISTS have predicted that the present business depression ultimately may pay big dividends to industry through the cumulative savings resulting from technical improvements and merchandising advances that might never have been developed under normal conditions. Waste prevention is a sound medicine for economic ills. In theory, this prescription may be applied not' only to raw materials, but also to labor, fuel, over- head, and other phases of production. Actually, how- ever, regardless of the efficiency of operating practices, waste is inevitable in the production of many commodities. The problem then becomes one of profitable utilization of waste rather than prevention.

Jan 1, 1932

By Thomas Read

PERSONNEL work is a term recently introduced to cover the great variety of activities in industrial work that deal with the human factor. Much attention has been focussed upon individual phases of personnel work, such as accident prevention, sanitation, "welfare" work, reducing labor' turnover, and so on. In most cases these activities have been carried on as though they were distinct and separate fields; as a matter of fact, they are only different phases of the single problem of human engineering, and each has important and fundamental relations with the others. Thus, for example, high labor turnover is one of the most .important causes of a high accident rate, and unsatisfactory housing conditions are an important cause of labor turnover. In the early stages of the study of these problems, it was necessary to take them up separately; the time has now arrived at which it is desirable to consider them as a whole in order to bring them into the right relation to each other. When thus considered as phases of an interrelated whole, they may be grouped as personnel work. A discussion of the importance of personnel work as a means of in creasing dividends in industry may be objected to by some as a too materialistic way of looking upon work that is humanitarian. Nothing could he more mistaken than such an opinion. Humanitarianism, per se, has no place in industry, and nothing is gained and much is lost in pre tending that it has. The only reason why a corporation engages in business is to make profits, and any activity of the corporation that does not tend either directly or indirectly toward that end is poor business. It is equally poor business to overlook any activities that do tend indirectly to the making of profits. On this basis, personnel work can be justified as a corporate activity; there is no justification whatever for abstract humanitarianism from the business standpoint. One characteristic of the American workman is a general high level of intelligence, and it is an insult to intelligence to ask a man to believe that anything so impersonal as a corporation is really desirous of benefiting

Jan 10, 1917

W. H. BASSETT,* Waterbury, Conn. (written discussion ?).-The effect of reducing gases on hot solid copper has been known for many years in the copper industry, and precautions taken to guard against it in the general practice in copper heating and annealing. In view of the statement that Bengough and Hill, in 1910, were the first to suggest the possibility of the formation of gas within the copper itself, it is interesting to note that in Harper's Magazine for April, 1904, an article, "Life and Diseases of Metals," by Professor Heyn, illustrated the effect of reducing gases on copper by a photograph, which is shown in Fig. 1. This he entitled "Copper burst asunder by disease." After referring to the effect of hydrogen on steel, he makes the following remark: "Similar symptoms of poisoning, caused by hydrogen or gases containing hydrogen (as gas for lighting purposes), are apparent in copper when exposed to red heat. Not every kind of .copper is susceptible to this poisoning in equal degree. Copper per-fectly free of cuprous oxide is entirely exempt from poisoning. Most of the various coppers of commerce, however, contain cuprous oxide, formed during the smelting process while exposed to atmospheric influences. In such coppers, containing cuprous oxide, hydrogen causes a terrible disease on the copper being heated red hot. The copper bursts asunder and is permeated by cracks. This disease is practically incurable and can be eradicated by resmelting only. The results work destructively according to the amount of cuprous oxide contained in the copper." It must have been evident to Professor Heyn, as it was to us on reading this article, that the bursting asunder of the copper was clue to the formation of steam. Practical copper heaters have known for many years that it was quite possible to produce blisters, or large gas holes, in the interior of copper plates or bars by heating to a high temperature in reducing gases. These facts, of course, do not detract from the value of the study of the action of hydrogen gas that has been made by Mr. Pilling, but simply illustrate that the practical effect of reducing gases on furnace-refined copper has long been a troublesome factor in the heating or annealing of that metal.

Jan 1, 1919

By H. M. Day, C. H. Mathewson

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy' in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in. the right region. PREPARATION OF ALLOYS The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By Michael A. Devane, Neil Duncan

Inclines and tunnels can extend from ground surface to considerable depths traversing a wide range of lithologies. The strata encountered may be affected by loosening and induced stresses at different locations along the route. It is suggested that Phase I of the pre- driving assessment process should include study of the geology, hydrogeology, rock material and rock mass characteristics. A rock mass disruption factor is used to express the ratio of the unconfined strength of intact rock material to the unconfined strength of in situ rock mass. It is suggested that there is a relationship between in situ (secondary) permeability values and the disruption factor, since the permeability of the rock mass is governed by parameters which influence strength. In Phase I1 of the pre-driving assessment, consideration should be given to the prediction of primary loosening which results largely from disturbances to the rock mass arising from the driving process. Also in Phase 11, preliminary assessments are made of the effects of induced stresses and of the geodurability characteristics of the rocks. In Phase 111, the mechanics of various secondary loosening pro- cesses are considered along with their relevance to estimates of stand up time and support requirements. Yield-line analysis is introduced for the study of plastic and brittle type bending deformations. Stand up time and support characteristics are also assessed. In Phase IV, the effects of induced stresses are analysed. It is suggested that even for broken rock in the Yield Zone, the rock mass disruption factor may not often increase above lo which is equivalent to an in situ permeability of 10-1 m/s.

Jan 1, 1983

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By R. W. Hyde, B. S. Old, S. E. Eaton

INTRODUCTION ONE of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects on both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steelmaking. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2.1 The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2,3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. Still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States, It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaSO4), The sulphur is subsequently found in the coke in combination with carbonaceous material of unknown composition and as calcium and iron sulphides: In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke, Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two major forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high in total sulphur, would yield coke of fairly low sulphur content, Using the new

Jan 1, 1948

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By A. U. Seybolt, J. L. Walter

The effects of the addition of 0.5 pct ThO2 (by volume) on the grain structure and texture of heavily rolled tungsten sheet were studied. Powder metallurgy ingots were rolled to sheet, 0.001 in. thick, and samples were annealed at temperatures from 1200" to 2500°C. The heating rate to the anneal temperature was varied from 3°C per min to 6500°C per min. The orientations of the largest grains were determined by X-ray diffraction. The disposition and loss of the ThO2 particles were determined by electron transmission microscopy and the activation energy for remozlal of the thorium was measured by mass spec-troscopy. Heating rates below about 800 C per min produced large, highly elongated grains. Higher heating rates produced much smaller, less elongated grains. The grain structure and texture of the slowly heated samples were identical to the structures and textures of heavily rolled tungsten foil conventionally doped with aluminum, silicon, and potassium but the recrystallization temperature was about 200°C lower. There was stringer-like dispersion of larger ThO2, particles superimposed on a uniform dispersion of fine particles. The particles increased in size and decreased in number with time at temperature. The loss of particles was accompanied by formation of grain boundary voids and surface pits. The activation energy for removal of the ThO2 was about 40 kcal per mole. THE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of heavily rolled sheet1 or drawn wire."4 Thus, "doped" tungsten sheet, rolled to 0.001 in. and recrystallized, develops a structure consisting of large, highly elongated grains of a specific preferred orientation.' It has been shown that the elongated grain structure was caused by a dispersion of particles, identified as mullite (Al6si2O13),1,4 in strings parallel to the rolling direction in sheet or to the wire axis. Identical results were obtained for iron which was doped with glass and rolled to 99 pct reduction of thickness and recrystallized.5 Again, the glass particles were disposed in strings parallel to the rolling direction. The strings retarded boundary migration in the lateral direction but grain growth was able to proceed relatively unhindered along the direction parallel to the strings.1,5 In both the doped tungsten and the glass-doped iron, the particles were highly plastic during the high-temperature deformation. Since mullite melts at about 1800°C and the glass employed melts at about 810ºC, the particles were probably molten during the recrystallization anneals (above 1800°C for the doped tungsten and 850°C for the glass-doped iron). There are indications in the literature that particles not plastic at hot-working temperatures (up to about 1550°C for tungsten) may also impart elongated grain structures by primary recrystallization of worked alloys. Examples are dispersions of tantalum carbide in chromium,6 and ThO2 in nickel where elongation ratios of recrystallization grains of up to 20:l were obtained.7 Strings of ThO2 particles in W-ThO2 wire have been seen by Rieck.8 In view of the available evidence, it was of interest to extend the previous studies of doped tungsten and glass-doped iron to include W-ThO2 sheet materials. Of specific interest was the grain structure, preferred orientation, recrystallization temperature, and disposition of the thoria particles. EXPERIMENTAL PROCEDURE A) Material Preparation. About 380 g of blue tungsten oxide (approximate composition WO3) was wet with a sufficient amount of aqueous solution of Th(N03)4 to provide 0.5 vol pct ThO2. The wet mixture was stirred to distribute the doping material uniformly throughout the powder. Stirring was continued while the mixture was heated until it was completely dry. The dried, doped mixture was then reduced to tungsten powder by heating at 850°C for 2 hr in a stream of dry hydrogen. The doped tungsten powder was hydropressed in a rubber sack at pressures of 50,000 psi to produce an ingot approximately 2 cm diam by about 5 cm long. Next, the pressed cylinder was heated in hydrogen for 2 hr at 1350°C to render it strong enough for machining. The cylinder was machined to a square cross section of 1.6 by 1.6 cm with rounded corners. Finally, the bar was heated for 2 hr at 2150°C in hydrogen to provide a sufficiently dense mate rial to withstand the hot-rolling operation. Prior to rolling, the ingot was reduced in thickness by about 20 pct by forging at 1550°C. This served to increase the density of the material and to widen it slightly for better rolling characteristics. The forged ingot was then rolled at 1550°C to a reduction of 45 pct of thickness, following which the rolling temperature was reduced to 1300°C and the slab rolled, with several reheats, to 0.050 in. Further reduction was accomplished at 800°C in tungsten sheet packs to a total reduction of about 99.85 pct. B) Annealing Treatment and Observation of Structure. Small samples of the rolled foil were annealed in one of two ways. Some of the samples were suspended in a covered tungsten can and annealed at temperatures from 1200" to 2200°C for various times in vacuum of l0-7 to 10-6 mm Hg. The can was heated by induction and temperatures were determined by optical pyrometry

Jan 1, 1970

By George Kunz

(Butte Meeting, August, 1913.) . THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact. that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it-would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct. weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.2

Jan 7, 1913

By Frederick G. Coqueron, Joseph E. Pogue

The purpose of this study is to present the results of a detailed survey of the financial and operating aspects of 30 oil companies comprising a major sample of the American petroleum industry. This review supplements a previous paper entitled "Capital Flow and Capital Formation in the Petroleum Industry, 1934-1941,"a and deals not only with a longer period but also gives new and more revealing analyses of the capital movements and characteristics. The data are gathered from published financial statements of the companies, especially the annual reports to stockholders and Form 10-K to the Securities and Exchange Commission, supplemented by confidential information. The 30 oil companies covered by this study are listed on the leading stock exchanges and for the purpose of analysis are grouped as follows: 9 companiesb engaged principally in crude production, 4 companiesc with production averaging in excess of refinery requirements, and 17 companiesd with refinery throughput in excess of crude production. These samples are sufficiently broad and representative to constitute norms against which individual company performances may be profitably compared. The 30 companies in 1942 produced 54 per cent of the Nation's total output of crude oil and refined 79 per cent of the country's crude run to stills. The financial data apply predominantly to the domestic oil business, although 15 of the companies have investments and operate facilities in foreign countries. The net value of these foreign holdings amounted to 724 million dollars, or 12 per cent, of the combined net assets of the 30 oil companies at December 31, 1942.

Jan 1, 1944

By L. Kaufman

An equation is derived relating AF a", the difference in free energy between austenite and martensite, to temperature and composition in the iron-chrmnium and iron-chromium -nickel systems. This equation is used to calculate at M,for low-carbon stainless steels. A method for utilizing the energetic equations to calculate M, in stainless steels is suggested. In addition, an explanation is given for the anomalous effect of chromium in forming a y loop concurrent with the lowering of M, in iron-base alloys. It has been demonstrated that the effect of alloying elements on the Ms temperature is strongly dependent upon the influence of the alloying element on the thermodynamic properties of the y and a phases. Notwithstanding the fact that alloying elements affect the Ms temperature by changing the lattice parameters, elastic constants, and inter-facial energies of the a and y phases, their primary role is a thermodynamic one. Thermodynamic analyses have been presented for the iron-carbon'-4 and iron-nickele systems in which equations are derived for Fa and FY, the free energies of the b.c.c. (or b.c.t.) and f.c.c. phases. These equations, which can be obtained with the aid of the equilibrium diagrams, can be used to help predict the Ms vs composition curves. This paper deals with a calculation of the thermodynamic properties necessary to compute AFffLY for iron-chromium alloys. In view of the lack of direct information concerning the activity of chromium in the a and y phases of iron, the regular solution approximationa,g was utilized to bridge the gap. After the necessary equations were derived for the iron-chromium system they were used to calculate AFff— Y for stainless steels by combining them with the previous results obtained for iron-nickel alloys. The results of these calculations offer a means of rationalizing the anomalous behavior of chromium in iron-base alloys. The latter depends on the regular solution approximation in contrast to the explanation offered by zener , which is based upon the "magnetic specific heat effect." THERMODYNAMICS OF THE IRON-CHROMIUM SYSTEM If y represents the atomic fraction of chromium in an iron-chromium alloy, then the free energy of the b.c.c. phase Fa, the f.c.c. phase FY, and the difference in free energy between the f.c.c. and b.c.c. phases of the same composition are given through [3] and Fmy represent the free energies of mixing of the a and y phases; while @era -' and uFea 4Y represent the difference in free energy between f.c.c. and b.c.c. chromium and iron respectively. The values of AEFe0ff4Y in the temperature range between 0" and 900K ( .

Jan 1, 1960

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Oct. 10 to Nov. 10, 1914: Jintaro Kojima, Ashio, Japan. E. R. Hinckley, Seoul, Korea. J. Homer Stover, Trenton, N. J. S. A. Taylor, Pittsburgh, Pa. Kirby Thomas, New York, N. Y. Lawrence Addicks, Douglas, Ariz. Keijiro Nishio, Tokyo, Japan. Noel Cunningham, Bethlehem, Pa. Alexander K. Hamilton, Chicago, Ill. E. C. Vigeon, London, England. Harold N. Lawrie, Portland, Ore. S. E. Fairchild, Jr., Philadelphia, Pa. C. Spence Thomas, Cardiff, Wales. W. C. Schmidt, Jr., New York, N. Y. Henry Tackmann, New York, N. Y. Kenneth C. Browne, New York, N. Y. Dr. David T. Day has resigned his position with the U. S. Geological Survey and opened an office at 1331 F Street, N. W., Washington, D. C., for practice as a consulting engineer.

Jan 12, 1914

Albin, B. R Billings, Mont. '28 Amster, Nathan L . , 25 Broad St, New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave, Chicago, Ill. '28 Baum, Frank G Hobart Bldg., San Francisco, Cal. '28 Bayless, Ron. William S Russ Bldg , San Francisco, Cal. ' 28 Bean, Louts H., V.P., Dwight P. Robinson & Co, Inc 125 E. 46th St, New York, N Y. '23 Beatty, Ross J 1105 First National Bank Bldg., Chicago, Ill. '28 Benwell, Oswald F 205 Colorado National Bank, Denver, Colo. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Bingham, Charles W 1542 Hanna Bldg, Cleveland, Ohio. '28 Blumenthal, Hugo 44 Pine St, New York, N. Y. '28 Boettcher, Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H Iola, Kans. '28 Bragg, E. B Carmel, Cal. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1923

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Nov. 10 to Dec. 10, 1915: F. Lynwood Garrison, Philadelphia, Pa. E. Fleming l'engle, Costa Rico, C. A. William J. Lakeland, Burma, India. Fred Maccoy, El Oro, Mexico. Dwight E. Woodbridge, Duluth, Minn. 0. N. Scott, Toronto, Ont., Canada. Chester A. Fulton, Yonkers, N. Y. K. P. Swenson, Tokyo, Japan. Willet G. Miller, Toronto, Canada. - H. L. Mead, New York, N. Y. L. G. Huntley, Pittsburgh, Pa. E. DeGolyer, Norman, Okla. L. E. Howard, Lockport, N. Y. J. S. Lane, New York, N. Y. H. W. DuBois, Philadelphia, Pa. T. V. Nonactre, Argentina. Howard R. Stewart, London, England. N. H. Darton, of the U. S. Geological Survey, has returned to Washington after a long season of field work in New Mexico investigating the prospects of finding potash deposits in the Red beds.

Jan 1, 1916