Search Documents

By J Youngson

Gold placers can be difficult to locate in areas where tectonic activity and paleogeography have changed significantly since placer formation. Existing placer exploration models are useful in areas that have a relatively simple geological history, identifiable relationships with parent sources, or a history of placer mining. However, exploration becomes increasingly difficult in areas where tectonic activity and sedimentary recycling repeatedly redistribute the gold. Gold placers in the Waitaki River catchment, North Otago, New Zealand have no primary source within the catchment. During the Eocene placer gold was transported by a river ('Buster River') that flowed in a northeast direction from Central Otago toward a coastline at Maerewhenua, North Otago. This river and coastal system was inundated by marine transgression during the middle Tertiary. Since the Miocene its placer deposits have been uplifted and eroded and any links with parent sources have been severed. Changes in paleogeography resulted in local reconcentration and local dilution of placer gold in different areas in the Waitaki catchment. Thin veneers of old Waitaki River gravels (Kurow Gravels), containing gold recycled from the older placers, have been deposited unconformably on strath surfaces cut into Tertiary or older rocks. These gravels along with remnant Eocene fluvial and shallow marine strata provide potential placer exploration targets. Uplift and erosion of non-auriferous rocks in the Waitaki catchment to the west and north of the study area has resulted in considerable dilution of potential placer deposits downstream, especially in areas of gravel aggradation. We present a placer exploration model that is founded on answering fundamental questions pertaining to the paleogeography and geological history of the sediments associated with the placers.

Jan 1, 1999

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

By K. R. Coulter

"Good morning gentlemen. I am very pleased to have this opportunity to tell you a few of the things that happen within a completely unrelated activity, the electroplating industry, except that it does consume metals and has some slight similarity of problems so far as cyanide is concerned.First, just a few general terms about the industry. It is a relatively unsophisticated industry technically, and in many instances there are serious problems in obtaining staff that can operate the various systems that are currently available for destroying cyanide or precipitating metals.I would suggest to you that if you are investigating any system that you consider very seriously the personnel that are actually going to run it. The installation people; probably have some idea what it is all about but the operators must be chosen for their ability and not because they just happen to be available.We perhaps have another area in common. There is very little money for capital expenditures that produce no immediate return or even eventual return on the investment.The industry is largely made up of ""Jobbers"" who are strictly electroplating. There is another group in which the electroplating is captive as in large companions where it is a convenience operation. Also there are specialists, who do other things besides plating but it is a very major part of their operation. This applies to the automotive parts industry.Cyanide applications in the plating industry will be for copper, zinc, cadmium, silver, brass, and gold. Cyanide waste solutions come from those solutions adhering to the plated parts, and from the occasional discharge of the plating bath solutions. Also, in a related industry, the heat treating people with cyanide case hardening have some high concentrations of cyanide to dispose of. Concentrations of cyanide that we treat are 2500 parts per million or higher especially in wastes from heat treating. Solution volumes might be as low as 100 gallons per hour in a well run, carefully operated rinsing system. It may be as high as 3000 gallons per hour where dilution occurs."

Jan 1, 1973

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

A recent Evening Post Headline read 'Officialdoms Inertia Risking Millions in Growth Strategy'. The article beneath that headline outlined the difficulties encountered by the Government's growth strategy projects and included the paragraph 'public efforts by Government to brush up communication of the widespread nature of its growth strategy is believed to have been matched by efforts in private by some ministers to overcome their frustration at the constant delay while reports and paper work are moved between departments and through the system'. The article went on to point out that these delays could cost New Zealand millions of dollars in lost overseas exchange savings. We as responsible citizens should be appalled or at least concerned that such costly delays should or even could occur. But those on the outside of the system who spend much of their working life prodding, reminding, pleading, cajoling, even begging, the bureaucracy should be excused a smirk or a smile or even a good belly laugh. The Minister is usually a part of the bureaucracy passing judgment on someone else's proposals. This time the Government has plans of its own. Plans which it wishes to see implemented as rapidly as possible and even with the assistance of the precautionary National Development Act with its 'fast track' provisions those plans have got bogged down in the bureaucratic machine which this Government has done as much as any other to create. In the circumstances, the thought of Her Majesty's Ministers frustrated at the constant delay while reports and paper work are moved between departments and through the system is not unpleasing.

Jan 1, 1982

By E. M. Shemang, C. E. Suh, L. Mbinkar, University of Yaounde

"Two iron deposits within the Precambrian mineral belt of Cameroon are described in detail for the first time: the Archean Metzimevin replacement iron deposit enclosed in Fe-enriched itabirite, and the Proterozoic granite-hosted, shear zone-related Mayo Binka magnetite deposit. In the Metzimevin de¬posit, quartz is corroded and microplaty hematite overprints martite-textured hematite. The Mayo Binka massive magnetite veins show evidence of deformation in magnetite (fracturing and microbrecciation) and in overgrowths of specular hematite (mechanical twinning and undulating extinction). The magnetite is partially replaced by hematite (martitization) and goethite. Ores from both deposits have >88% total Fe2O3 and low contents of contaminants such as SiO2, Al2O3, MgO, CaO, P2O5, and TiO2. They are also poor in Cu, Pb, Zn, V, Cr, and Ni. The Metzimevin massive hematite is characterized by an accentuated light rare earth element depletion relative to the Fe-enriched itabirite. It is suggested that the Metzimevin iron deposit is the result of hypogene leaching of gangue minerals from, and further hematitization of, an itabirite protore. Although the genesis of the Mayo Binka massive magnetite is unclear, it is spatially related to Neoproterozoic granitic rocks. The data allow some comparison of these little known, but pot¬entially economic iron deposits, with some of the world’s better investigated deposits, and are useful to the exploration efforts for iron ore currently underway in Cameroon and the Central African subregion.Deux gisements de fer de la ceinture minérale Précambrienne du Cameroun sont ici décrits en détail pour la première fois : le gisement de fer Archéen de Metzimevin formé par remplacement et encaissé par des itabirites enrichies en Fe, et le gisement de magnétite Protérozoïque de Mayo Binka as¬socié au cisaillement dans un granite. Au gisement de Metzimevin, le quartz est corrodé et de l’hématite en microplaquettes se développe au dépends de l’hématite a texture martitique. Les veines de magné¬tite massive de Mayo Binka présentent des évidences de déformation dans la magnétite (fracturation et microbréchification) et dans les surcroissances d’hématite spéculaire (Macles tectoniques et extinction ondulante). La magnétite est partiellement remplacée par l’hématite (martitisation) et par la goethite. Le minerai des deux gisements contient >88% de Fe2O3 total et un faible contenu en contaminants tels que SiO2, Al2O3, MgO, CaO, P2O5, et TiO2. Il est également pauvre en Cu, en Pb, en Zn, en V, en Cr et en Ni. L’hématite massive de Metzimevin est caractérisée par un appauvrissement relatif en terres rares légères relativement à l’itabirite enrichie en Fe. Il est suggéré que le gisement de fer de Metzimevin résulte du les¬sivage hypogène des minéraux de la gangue ainsi que de l’hématitisation poussée d’une préconcentration de fer dans l’itabirite. Bien que la genèse de la magnétite massive de Mayo Binka demeure obscure, elle est spatialement associée aux roches granitiques Néoprotérozoiques. Ces données permettent de comparer ces gisements de fer peu connus et potentiellement économiques avec certains des gisements mondiale¬ment mieux connus, aidant ainsi les efforts d’exploration présentement en cours en Afrique de l’ouest et au Cameroun."

Jan 1, 2008

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By Fookes R. A, Bunch K, Gravitis V. L, Watt J. S

The combustible volatile matter in coal mine roadway dusts (CVM) has been determined using x-ray backscatter techniques. The correlation between x-ray and chemical techniques is reasonably good for the 92 samples from collieries on the Bulli seam, and the maximum error expected at the maximum level of 11· 5 weight per cent CVM permitted in the N.S.W. Coal Mines Regulation Act, 1912, as amended, is about ± 2·5 weight per cent. This x-ray technique can be used only when the combustible volatile content of the coal matter (cvm) varies within a limited range, and a separate calibration is required for each coal seam.Portable equipment based on a radioisotope x-ray source ahd digital ratemeter makes possible simple and rapid analysis, and with adaptation to use in coal mines should lead to much more comprehensive testing- ofroadways and hence improved overall prevention of coal dust explosions.

Jan 1, 1977

By Robert B. Parsons

"Exploration and development of mineral resources in developing countries by Canadian-based multinational mining companies is becoming increasingly common. One problem being encountered is that the objectives of the governments of developing countries can differ from those of developed countries. These objectives are not always consistent with maximizing returns from the projects, which can create conflicts between the mining company's responsibility to its shareholders and the desire to be a good corporate citizen. This article discusses how a mining tax regime can be designed to make the social goals of a government consistent with the economic goals of the company.IntroductionAt the recent International Seminar on Mining Taxation organized by CIM and the United Nations there was considerable discussion about the role of international mining companies operating in developing countries. Not surprisingly, given the diversity of backgrounds of individuals attending the Seminar, there were different opinions about what this role should be.Government PositionRepresentatives of governments pointed out the strong desires of their countries for technology, high-level technical training of their workforce, increased employment, and development of social infrastructure. They pointed out that, to a large extent, these objectives could be more efficiently met by mining companies operating in the country than by the governments themselves. For example, a multinational mining company (""MMC"") would have extensive knowledge of the various technologies available, and would have performed a detailed evaluation of the mineral resources before choosing the most cost-efficient technology for that project. They would, therefore be in an ideal position to assist the country in importing and developing such technology. Similarly, the company could provide opportunities for hands-on training, both at the technical and managerial levels, which would otherwise be unavailable to the government."

Jan 1, 1991