Search Documents

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By Bob Turnbull

The dictionary definition of calibration is: to determine by measurement or comparison with a standard, the corre c t value for each scale reading on a device.1 As a consultant or blast contractor, you assess risk every day. But, have you considered the importance of, and the risks associated with the calibration of your seismograph and the accuracy that is p rovided? Can your calibration pro v i d e r back you up in times of trouble and provide documented evidence that the equipment was functioning within specification? Can their calibration pro c e d u res withstand independent scrutiny and be shown to be traceable to a National Standards for accuracy of measurement? These are important documents that in court provide tremendous support that blasting and monitoring activities are conducted professionally and competently.

Jan 1, 2004

By Milton Camino Ramos

MARSA forma parte de los yacimientos vetiformes de la franja metalogenética aurífera del Batolito de Pataz, y políticamente se encuentra ubicado en la provincia de Pataz, La Libertad. En este sentido, el presente texto describe los resultados del programa de exploración 2010-2011, donde se dio el descubrimiento del primer cuerpo mineralizado del yacimiento, el cuerpo Esperanza, entre otras ocurrencias. Asimismo, se muestra que los cuerpos mineralizados de la franja metalogenética de Pataz, se formarian en estructuras de primer orden con evidencias de reactivacion, cuyo sistema estructural funciona como entrampamiento y en varias etapas de mineralizacion.

Sep 12, 2011

By G. Noce

The ever more present necessity for greater precision in foundation structures on vertical piles subject to horizontal forces applied to the heads, in the light of of the latest knowledge about the elastic-plastic behaviour of the soil has led to the use of numerical calculation for the formulation of a general resolution method for the problem. The calculation method that will be set out, applicable to piles with inertia moments variable discreetly along their axes is especially useful when studying steel structures for medium and large tonnage vessels for which the metal piles are often constructed for the assembly of section of equal external diameter but different thickness and therefore different inertia moments. Two examples are given of constructions whose foundations have been projected with these calculation tools, one in the railway sector (foundation pile for the river Nera viaduct - Italy) important for the limitation of horizontal relative deck displacement, the other maritime (Dolphins of the petroleum pier of the port of Bandar Abbas - Iran).

Jan 1, 1989

By V. N. Cox, C. H. Grant

Both the underwater method and the rock cratering method contribute useful information in evaluating and comparing new explosive compositions. Results indicate that metallized explosive systems which contain no high explosives can be formulated to offer more energy and to do potentially more work than other slurry explosive systems. Commercial field trials are presently being conducted with a metallized explosive that does not contain any high explosive. Although there have been only a few commercial blasts to date, the results are encouraging. The Dow Chemical Co. has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which DOW is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of nonmetallized explosives currently being used. Early in 1960, additional patent rights were acquired from independent inventors and a development station at Virginia, Minn., was set up to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the boreholes. Due to the complexities involved in controlling the manufacture of the explosive in the borehole, performance was sometimes in doubt. Furthermore, experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over 2000 charges of 8 to 60 lb under water and in taconites and granites with many types of explosives, a metallized explosive was developed which is now being manufactured at a pilot plant in Virginia, Minn. and is being evaluated commercially. UNDERWATER METHOD An underwater method of evaluating explosives has a number of advantages. A permanent site can be established and operated indefinitely. A large number of charges may be fired in a short length of time. The medium in which the explosive is shot is exactly the same for successive shots. Data are recorded electronically minimizing human judgment. A disadvantage of the underwater method is the lack of confinement provided by the water medium. Many explosive compositions require a greater degree of confinement to develop good energy release. Although the relative significance of the two components of energy release that are usually measured, the shock energy and the bubble energy, and their relationship to breaking rock are not clearly understood, the underwater method is a valuable research tool for screening explosive compositions and gaining an insight into the manner in which explosives release their energy. Fig. 1 shows schematically the underwater apparatus. The piezoelectric gages are calibrated tourmaline crystals which convert the shock wave to an electrical impulse which is transmitted to an oscilloscope and recorded on Polaroid film. The shock traces are picked up by scopes 1 and 2. Scope 1 is timed to pick up the full trace whereas scope 2 is timed to cover the first increment of the shock trace expanded, and therefore allows full inspection of the propagation and peak pressures. Scope 3 records the bubble trace. When the explosion occurs, a bubble of gaseous detonation products is formed. The outward momentum of the water keeps expanding the bubble even after

Jan 1, 1963

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By Yoginder P. Chugh

The characteristics of weak floor strata associated with actively mined coal seams in Illinois are very important from ground stability point of view and, in many cases, are the governing factors in determining the size of pillars and mine openings. Laboratory and field getotechnical characterization studies of weak floor strata were conducted at six mines during the period 1985-1988. Correlation analysis among engineering index properties, and laboratory, and field determined strength-deformation properties were conducted to identify simple tests which can be used to estimate ultimate bearing capacity and deformation properties of immediate floor strata. It was concluded that the ultimate bearing capacity (UBC) and strength- deformation properties of the weak floor strata can be estimated from simple tests such as, natural moisture content, atterberg limits, and axial swelling strain. Indirect tensile strength was found to be a better estimator of UBC than unconfined compressive strength.

Jan 1, 1989

By P Mitchell, J Proffett, I Munajat

Batu Hijau is an island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Sunda-Banda archipelago of Indonesia. Southwest Sumbawa Island is underlain by Early Tertiary, low-K calc-alkaline to weakly alkaline volcanic and intrusive rocks. Within the mine area the oldest exposed rocks are medium- to thick-bedded, medium to coarse andesite volcanic lithic breccia, thin bedded, fine-grained volcaniclastic sandstones and mudstones and hypabyssal porphyritic andesite. In the eastern portion of the mine area there is a thick sequence of quartz diorite that postdates the andesites. A small stock of Equigranualar Quartz Diorite predates the Batu Hijau deposit and occupies the contact between the andesitic volcaniclastic sequence of rocks and the Porphyritic Quartz Diorite. Batu Hijau is a world-class copper-gold deposit that has a drill indicated mineable reserve of 914 million metric tonnes grading 0.525 per cent copper (10.58 billion pounds copper) and 0.403 g/t gold (11.8 million ounces gold). Mineralised material not in reserve accounts for an additional 580 million metric tonnes at 0.328 per cent Cu (4.19 billion pounds copper) and 0.171 g Au/T (3.19 million ounces gold), and including an oxide copper resource of 57 million tonnes at 0.37 per cent Cu and 0.12 g Au/T. Copper and gold mineralisation is directly related to quartz veining and wall rock alteration that developed with multiple tonalite porphyry intrusions. The tonalites were emplaced along the contact between the andesitic volcaniclastic rocks and quartz diorite intrusives. Copper and gold are zoned around the porphyry intrusions, which are designated by their contact-age relationships and other features as Old Tonalite, Intermediate Tonalite(s), and Young Tonalite(s). The Old Tonalite was the first copper-bearing intrusion, and although it is the smallest intrusion it has the highest quartz vein density, the strongest alteration and the highest grade. At least two tonalite porphyry intrusions followed the emplacement of the Old Tonalite. Each of these intrusions was associated with less quartz veining, weaker hydrothermal alteration and lower grade copper and gold than the previous intrusion. The intrusive cycle culminated with the emplacement of the Young Tonalite, which contains relatively few quartz veins, is weakly altered and mineralised. Hypogene hydrothermal alteration and sulphide mineralisation developed in five temporally and spatially overlapping stages. These stages consist of Early, Transitional, Late, Very Late, and I Zeolite alteration. Early alteration and sulphide mineralisation accompanied each tonalite porphyry intrusion, but with diminished intensity in each subsequent intrusion. Transitional and later stages of alteration and mineralisation postdate the tonalite porphyries and overprint Early stage alteration and mineralisation. Early alteration and mineralisation consisted of biotisation, secondary magnetite and plagioclase development, fine porphyry-style stockwork veining and ore mineralisation. Magnetite-biotite????quartz stringers and dark micaceous (biotite-sericite) veinlets were developed. The veinlets were accompanied by biotisation of magmatic mafic minerals and groundmass. Thin, irregular and discontinuous æAÆ type quartz veinlets and fine-grained chalcocite, digenite and bornite mineralisation accompanies the Early alteration. It is hypothesized that most of the copper mineralisation was originally deposited as bornite, digenite and chalcocite. Secondary plagioclase was added along the selvages of the early quartz veinlets. Early alteration is pervasive within and proximal to the tonalite porphyries. In the distal portions of the deposit, andalusite and anthophyllite formed at intermediate to shallow depths, and in the deeper portions of the deposit, respectively. The andalusite and anthophyllite probably developed at the same time as the early magnetite-biotite-quartz alteration in the core of the deposit. Transitional-age alteration consists of oligioclase/albite-sericite-chlorite- quartz-¦vermiculite and is associated with æBÆ quartz veins. Through-going planar æBÆ veins are thicker than æAÆ and æA-familyÆ veinlets and have chalcopyrite????bornite along vuggy centrelines and narrow oligioclase????albite alteration envelopes. Rare æCÆ chalcopyite¦quartz veinlets were also formed during Transitional alteration. During Transitional alteration early copper sulphide minerals (chalcocite, digenite and bornite) are converted to bornite and chalcopyrite. The majority of the copper (50 - 70 per cent) in the deposit is contained in ores in which chalcopyrite is the predominant sulphide. Late alteration consists of feldspar destruction and replacement by sericite and other minerals. The late alteration is accompanied by the development of æDÆ sulphide veinlets and veins. These veins consist of pyrite and quartz????chalcopyrite. Within the halos of the late pyritic veinlets biotite is replaced by sericite, quartz-sericite, quartz-andalusite, or quartz-pyrophyllite+kaolinite replace plagioclase, and magnetite is converted to specularite and/or pyrite. In the periphery of the deposit, the feldspar destructive alteration, together with outer zones of Transitional-age alteration, constitutes what is commonly referred to as a æpropylitic zoneÆ. Very Late hydrothermal alteration is also characterised by feldspar destruction, but differs from Late alteration in that feldspar is replaced by smectite in association with sericite and chlorite. Sulphide mineralisation in this stage consists of sphalerite, galena, tennantite, pyrite and chalcopyrite. The last stage or I Zeolite alteration consists of low-temperature, open space filling consisting of stilbite or laumontite¦calcite. Supergene oxidisation of the orebody extends to a maximum depth of 210m. Isolated deep oxidation occurs along open fracture zones to depths of ~400 metres along æDÆ vein filled fracture zones. Weak supergene copper enrichment occurs in a thin horizon (15 to 60 m thick) that blankets the top of the deposit. The main supergene copper mineral is secondary æsootyÆ chalcocite replacement of sulphide grains and as veins.

Jan 1, 1999

By Osetzky D, Hesp W. R

The treatment of a hydrobiotite containing 0&#183;64 per cent copper with various soluHons showed that a high percentage (up to 90 per cent) of the copper can be extracted under mild conditions (1 M BCI, 85&#176;C) or withsaline solutions (20 per cent by weight NaCI or NH4F, 400&#176;C). The latter results suggest that the copper is incorporated in the interstratified vermiculite of a vermicuHte-biotite mica and the solutions (NaCl and NH4F) which reacted with the vermiculite without attacking the biotite gave the highest extraction yields.In general, extraction yields with saline solutions increased with the temperature (between 100 and 400&#176;C) and duration (3 or 6 days) of the treatment but were not appreciably affected by the initial pH of solutions.The results of RCI treatment especially may have a bearing on the hydrometallurgical treatment of refractory copper ores where copper is tied to gangue silicates.

Jan 1, 1977

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimum when the concentration of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/ liquid ratio of 67 g/L, stirring speed of 400 rpm, and leaching duration of 60 min. Under this condition, 90.49% and 6.78% of Mn and Fe were dissolved, respectively, from the ore sample with a size fraction of − 106 μm. It was determined that the leaching of manganese from the ores was a second-order reaction with an activation energy (Ea) of 53.38 kJ/mol. The leaching residues obtained under the optimum condition were subjected to high-intensity wet magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20% Fe and 1.79% Mn with iron and manganese recoveries of 56.83% and 66.73%, respectively. A magnetic separation test from an unleached ore sample was also carried out as a benchmark. To the best of our knowledge, this is the first time that a magnetic separation process was used to a residue obtained from reductive acid leaching of manganiferous iron ores to recover iron.

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimum when the concentration of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/ liquid ratio of 67 g/L, stirring speed of 400 rpm, and leaching duration of 60 min. Under this condition, 90.49% and 6.78% of Mn and Fe were dissolved, respectively, from the ore sample with a size fraction of − 106 μm. It was determined that the leaching of manganese from the ores was a second-order reaction with an activation energy (Ea) of 53.38 kJ/mol. The leaching residues obtained under the optimum condition were subjected to high-intensity wet magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20% Fe and 1.79% Mn with iron and manganese recoveries of 56.83% and 66.73%, respectively. A magnetic separation test from an unleached ore sample was also carried out as a benchmark. To the best of our knowledge, this is the first time that a magnetic separation process was used to a residue obtained from reductive acid leaching of manganiferous iron ores to recover iron.