Search Documents

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

By Ashley P, Neale T

Alluvial gold was discovered on Sudest Island in 1888, and by 1893, an official production of 10 000 oz had been won by expatriate miners from shallow alluvial and colluvial workings. Hardrock sources were located and while one was developed at Mt Adelaide, production is unknown. Sudest Island comprises mostly phyllites and lesser coarse grained rocks which are cut by metamorphic quartz veins and basic (locally shoshonitic) intrusives. Sheared and altered basalts and serpent- inites represent are believed to be elements of an ophiolitic suite inferred to be associated with metamorphic core complex development and thus similar to tectonic environments on Misima and the D'Entrec- asteaux Islands. No epithermal-style quartz suggestive of a target similar to that on Misima Island has been identified on Sudest. A hardrock source for the alluvial and colluvial gold is interpreted to be metamorphic quartz veins similar to those in the Bendigo- Ballarat Zone of central Victoria, possibly remobilising gold derived from the meta- sedimentary and meta-igneous rock pile. The present focus is on development of a small scale alluvial gold mining operation in conjunction with exploration for hardrock targets. This latter programme remains at a reconnaissance stage.

Jan 1, 1991

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

By Eugene McAuliffe

In the year 1581, the counselors of King Philip of Spain suggested to that monarch that a canal across the Isthmus of Darien would open the west coast of the South American continent to Spanish miners and explorers, enlarging and expanding the flow of precious metals then just beginning to trickle across the path cut by Spanish Conquistadors, from old Panama to Puerto Bello on the east coast. The King sent out a party of surveyors and explorers under the command of a young engineer, Savadaerro, who returned after two years, reporting upon a location for a canal which was virtually adopted by the French engineers employed by De Lesseps, who in 1877 commenced the work of constructing the Panama Canal-296 years after Sava- daerro's first survey was begun. The suggestion for an Isthmian canal, made to the king at a time when Spain was a proud, virile nation and when that country was contending with England in the fields of discovery and conquest, represents a measure of vision that has never failed to intrigue the imagination. That the young Spanish engineer recommended an undertaking so gigantic in conception that it took three and one-third centuries for its completion from the time it was first visioned matters little. In the day of Philip of Spain,

Jan 1, 1932

By N. Gatelier, T. You, J. C. Kandel

ABSTRACT: Underground hydrocarbons storage is a very specific domain for the designer. He is usually free to adjust the section, shape and layout to cope with the geological and geotechnical conditions. This paper presents a panorama of the geotechnical design of mined underground storage caverns, then lists a number of uncommon features encountered in a storage excavated in Sydney, Australia, the Elgas LPG project that had to face major non-isotropic conditions with numerous local variations, impacting on the achievement of the design profiles. Changes in geotechnical design methodology and practice are examined through this project, now in operation, which will have lasted altogether almost ten years. KEY WORDS: underground storage, geotechnical engineering, stability, methodology, design. ZUSAMMENFASSUNG: Die untertaegige Speicherung von Kohlenwasserstoffen unterliegt in der Planung sehr spezifischen Bedingungen. Der planende Ingenieur hat bei der Dimensionierung und Formgebung der Speicherhohlraeume gewisse Freiheiten, muss jedoch vorgefundene geologische und geotechnische Bedingungen beruecksichtigen. Der vorliegende Beitrag gibt zunaechst einen allgemeinen Ueberblick ueber die geotechnische Planung von bergmaennisch aufgefahrenen Speicherhhohlraeumen. Darueber hinaus werden Besonderheiten betrachtet, mit denen das Elgas LPG-Speicherprojekt in einer bergmaennisch aufgefahrenen Kaverne in Sydney, Australien konfrontiert war. Hierbei ging es um die Beruecksichtigung anisotroper Bedingungen mit zusaetzlichen Heterogenitaeten im Gestein und den daraus erwachsenden Schwierigkeiten, die geplante Hohlraumform zu verwirklichen. Ueber einen Zeitraum von fast 10 Jahren, in denen das jetzt in Betrieb befindliche Projekt unterschiedliche Betriebsphasen durchlaufen hat, wurden verschiedene geotechnische Entwurfsverfahren auf ihre Anwendbarkeit geprueft. SCHLUESSELWOERTER: Untergrundspeicherung, Geotechnik, Stabilitaet, Entwurfsverfahren, Planung. RESUME : Le stockage souterrain d’hydrocarbures est un domaine très spécifique pour le concepteur, car celui-ci dispose d'une large liberté pour adapter les sections, les formes et les implantations aux conditions géologiques et géotechniques de l’environnement choisi. Après un panorama de la conception géotechnique des stockages souterrains d’hydrocarbures par la méthode dite des cavités minées, l’accent sera mis sur un certain nombre de particularités rencontrées lors du projet de stockage de GPL de Elgas à Sydney en Australie, creusé dans de très fortes conditions d’anisotropie du massif rocheux, avec de nombreuses variations locales et toutes les implications que cela peut avoir sur le maintien des formes. L’évolution des approches méthodologiques géotechniques durant la dizaine d'années de développement de ce projet depuis les premières études jusqu'à l'exploitation actuelle est également présentée. MOTS-CLEFS : stockage souterrain, géotechnique, stabilité, méthode, conception.

Jan 1, 2003

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

Difficulties were experienced in the identification of carbonate minerals intimately associated with iron oxides in the so called carbonate ore, which occurs at depth in the Iron Duke Orebody.Determination of refractive indices by examination under the microscope using the immersion method, together with inferred chemical composition indicates that dolomite and parankerite are common constituents. Histograms of the manganese and sulphur contents strongly suggest that manganese is associated with the carbonate minerals, and that the highest sulphur assays occur near the base of the carbonate body.From the present work it is concluded that refractive indices indicate only a very approximate composition for carbonates of the parankerite type.The different carbonate minerals occur in irregular zones.INTRODUCTIONThe Iron Duke deposit is situated in the southern portion of the South Middleback Range on Eyre Peninsula, S.A., 30 miles from Whyalla. (Fig. 1).Drilling at Iron Duke revealed a large body of so called carbonate ore, which was tested in detail at cross section 1000 ft. S by three diamond drill holes, DDH.57, 67 and 78. (Fig. 2)Most specimens of carbonate ore described below were obtained from DDH 67 and 78.GENERAL GEOLOGYThe South Middleback Range is composed of two parallel ridges trending north-south. The Iron Duke orebody is situated on the southern portion of the western ridge. (Fig.1) .The rocks of these ranges belong to the Middleback Group which rests on a gneiss complex. Their age is considered to be Middle Precambrian or late Archaean.

Jan 1, 1963

The uphole bench extraction strategy at EKJV Management Pty Ltd?s Raleigh Mine, requires simultaneous horizontal and vertical exposure of paste filled stopes. In order to prevent excessive ore dilution, the paste fill must be of sufficient strength to prevent failure during exposure. A numerical modelling methodology has been developed to accurately simulate the initial stress distribution within paste filled stopes, together with the strain-softening loading response of paste fill material. Due to the narrow orebody width and high deformation behaviour of the host rock mass, high closure strains are likely to cause a stiff, brittle fill material to undergo crushing failure upon exposure. The stability of paste fill exposures at the Raleigh Mine was determined by conducting a series of three-dimensional numerical models that incorporate the extraction, filling and exposure sequence of paste filled stopes. Stability charts for 2.5 m and 3.5 m wide simultaneous horizontal and vertical exposures have been derived based upon the numerical modelling results. Implementation of the stability charts has proved successful in limiting the amount of ore dilution from paste fill and provides a basis to optimize paste fill cementation and stability throughout the life of the mine.

May 1, 2007

By Tom Treleaven, Andrew Williams

The town of Greenwich, CT, an exclusive suburb of New York City awarded several contracts for the installation of sanitary sewer in the North Mianus section of town. The Valley Road section was the most challenging from a rock excavation standpoint. The cut was up to 14 ft (4.25m), with adjacent utilities [20 in. (500mm) water, 6 in. (150mm) water and 8 in. (200mm) gas] located to within 5 ft. (1.5m) of the proposed sewer trench. Rock types varied but were ultra metamorphic in nature, ranging from quartzites, granite gneiss and various types of migmatities.

Jan 1, 2004

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

Jan 1, 1966

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By Jackson R. Pressley, M L. Hopkins, R E. Danell, N T. Moxon, Andrew Bowman

Efficient and cost effective blasting is achieved by closely matching the explosive energy to the strength of the material in which it is being used. Although there are many empirical relationships wich approximate this situation complete the blast optimization can only be achieved by quantitatively assessing explosive/rock interactions and explosive performance. The performance of an explosive is essentially governed by its velocity of detonation or the rate at which the detonation wave travels through the explosive column.

Jan 1, 1991

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012

IN presenting a&apos;description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969