Search Documents

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By T Hirsi, M Weatherseed, T Ritasalo

Cooling tower design has not advanced significantly in the last decade. Recognising this, Outotec has developed an innovative horizontal outflow cooling tower with increased performance compared to conventional design cooling towers.Outotec® Cooling Towers operate today in applications such as spent electrolyte cooling in zinc plants and for gypsum removal before copper solvent extraction. In such applications the use of this latest design has enabled increased production and lower maintenance costs in the downstream operations.In actual operations, the cooling performance has been confirmed at start-up, and has demonstrated that the towers operate in accordance with the CFD modelling. In the last three years these towers have proven themselves in commercial operation to operate with high efficiency and availability.This case study will outline comparative data, collected over two years at a site where both Outotec and conventional cooling towers are operating. The data shows that Outotec cooling towers require less than half the maintenance time of conventional cooling towers, when adjusted to a total solution flow basis. A close partnership approach with the site has allowed continual development, ensuring high availability and high performance.Experience with previous cooling tower installations guided the development of maintenance philosophies and procedures; this resulted in a design where maintenance intensive components were accessible from the top of the cooling tower. This allows safe access to components and maintenance with little or no downtime.CITATION:Hirsi, T, Ritasalo, T and Weatherseed, M, 2015. Improving cooling tower performance with innovative horizontal outflow design, in Proceedings MetPlant 2015, pp 396–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By A. M. Tunstall

Aspects of blast vibrations, damage mechanisms and the influence of rock quality on damage severity are reviewed and results presented from a monitoring programme in which the rock mass rating for six tunnels was determined. The peak particle velocity induced in the tunnels during open-pit blasting was measured and the tunnels were inspected visually for fresh damage after each blast. The results suggest that the quality of rock in which an excavation is situated has an influence on the level of ground vibration to which it can be subjected without sustaining damage. This means that the use of a single limiting value of peak particle velocity, as in the blast damage criteria for residential structures, is not ideal and may result in damage to excavations in poorer-quality rock masses

Jun 19, 1905

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

The Wainui Mill was conceived as a 60 - 90 t/d central mill to process gold ores of the Thames area of New Zealand from small mines in the district. The ores of the region exhibit various degrees of refractory response to conventional cyanidation leach due to the fineness of the gold, and association with pyrite. The alternative circuits involving cyanidation, flotation, and possible small-scale smelting are examined. The environmental impacts have been audited by the Commission for the Environment and were found to be acceptable.

Jan 1, 1986

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

Researchers examined datasets from two separate studies that measured common demographic variables but different safety performance outcome variables. Of specific interest was how types of experience might relate to workers’ preparedness to effectively mitigate or respond to both routine and nonroutine risk in the mining industry. The results suggest that individual factors such as length of job, industry, and mine experience are predictive of routine safety performance — as measured by self-reported proactive and compliant safety behaviors — and/or nonroutine safety performance — as measured by perceived competence in self-escape knowledge, skills and abilities (KSAs) — in significant and sometimes unexpected ways.

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

Mt Waruwari, host to the Porgera underground gold mine in the Highlands of Papua New Guinea (PNG), is a prominent ridge of sediments and dioritic intrusives rising approximately 600m above the surrounding valley floor. Consequently, mining occurs in a low stress environment where structural and material considerations are foremost in the design of ground support and reinforcement. Three major rock types are encountered in the underground mine. These are locally referred to as "black sediments" (slightly indurated mudstones and clayey siltstones), "altered sediments" (derived from black sediments by thermal metamorphism), and "intrusives" of dioritic composition. The rocks are moderately to highly fractured, the black sediments being generally weak and occasionally sheared while the altered sediments and intrusives are quite strong but often brittle. Mining takes place from a series of stopes extracted by either slot and mass blast or a modified vertical crater retreat method (VCR), which are backfilled with a cemented rock fill. Ground support and reinforcement has been relatively conserv- ative to date and generally relies on pattern reinforcement of all development with cement grouted "rebar" bolts and mesh, extending to pattern cable bolting with occasional mesh in stope backs. In addition there has been considerable reinforcement of stope hangingwalls in some cases. A programme of broad scale structural mapping, monitoring with extensometers, material property testing, and stress analysis has been devised to allow optimum design of ground support and reinforcement in the future. Considerable work remains to ,omplete this task.

Jan 1, 1991

By C A. Locke, J Cassidy, J L. Mauk

The Waihi-Waitekauri region hosts numerous low-sulfidation epithermal deposits that both outcrop and occur at depth. Zones of intense hydrothermal alteration enclose the Au-Ag bearing quartz vein deposits. Hydrothermal alteration includes the destruction of magnetite by hydrothermal fluids, pervasive silicification adjacent to quartz lodes and potassium enrichment due to adularia and illite deposition. High-resolution airborne magnetic and radiometric, and new gravity data delineate distinct geophysical anomalies associated with hydrothermal alteration and mineralisation. Five magnetically quiet zones occur in the region varying in size from 3 to 34 km2 and in geometry from circular to irregular zones. These zones represent the near-surface extent of strong to intense hydrothermal alteration associated with fossil geothermal systems. All epithermal deposits in the region occur in magnetically quiet zones. Over 120 new gravity stations together with existing data across the Waihi district have defined a positive Bouguer gravity anomaly coincident with the magnetically quiet zone. Eastern and western gradients of 50 gu/km bound the anomaly that contains two flat gravity highs west and east of the Waihi deposit. Strong potassium signatures in airborne radiometric data correlate with outcropping zones of alteration and are consistent with the presence of adularia and illite minerals. Hydrothermally altered zones are represented by areas of low Th/K ratios as a result of low thorium concentrations in andesite and elevated potassium levels in altered zones.

Jan 1, 2003

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

By S. Z. Pethö, H. Yilmaz

South Deep Mine is currently undertaking numerous voidfilling projects using low strength aerated cement products. Representative samples from one such site, were taken and tested for the load deformation behaviour under uniaxial loading conditions. The process of sample collection, laboratory preparation and testing are explained in detail. The results of testing were analyzed and the critical aspects pointed out as a design consideration to be implemented as part of the quality control and assurance program. Design aspects and underground application of the aerated cement product are discussed for the particular site on 58 level SV1. A simple instrumentation has been designed and installed to enable monitoring of any future movements in this area. A quality control and assurance process has been formulated enabling all aspects of the support installation in this excavation to be signed off.

Jan 1, 2003