Search Documents

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

"Chairman: Professor J. Elbrond Rapporteur: Miss V. E. MartingPapers.Aids to planning production in coal mines by F. H. Deist and M. P. RobertsCapacity calculations, investment allocation and long-range production scheduling in German coal mines by F. L. WilkeOre reserve evaluation and open pit planning by J. M. Marino and J. P. SlamaThis session was devoted to the economic aspects of planning and scheduling. After Dr F. H. Deist had introduced the paper Aids to planning production in coal mines, Dr T. V. Falkie summarized the following formal contribution prepared jointly with Dr R. V. Ramani, describing the work that has been done at the Pennsylvania State University in the development of simulation programs for mine planning over the past 15 years:During the late 50's and early 60's, Monte Carlo simulators were developed to model continuous miner-shuttle car transport systems, track haulage systems, belt conveyor networks, etc. In the mid-60's attention was directed towards deterministic simulation of equipment performance, given the equipment characteristics and the system profile. In the late (10's all these systems (miners, shuttle cars, belts and trains) were integrated together to form a complete coal mine simulator and the program could predict the output potential of the system, given the mining dimensions, method and equipment employed. The actual sequence of coal-cutting operations is entered into the computer through the use of a special programming language which permits any type of mining configuration to be simulated. The simulator is hybrid in nature in that the shuttle cars, trains and belts are simulated deterministically, whereas rate functions with delay frequencies are entered for the continuous mining operations of sumping, shearing, fleeting, cleaning, etc. With suitable manipulation of the data, the program may be applied to all belt or conventional mining sections. Most of these simulators were developed through the assistance of grants from the Department of Mines and Mineral Industries of the Commonwealth of Pennsylvania and are available from the Coal Research Board of the Commonwealth,"

Jan 1, 2014

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semivariogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size, and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that the ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semivariogram model should take a value of zero, a value equal to the nugget effect, or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semivariogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3 ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and Web courses, the definition of the semivariogram is ambiguous as the formulae for semivariogram models is not actually specified at zero distance6,7,8.

Jan 1, 2010

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By J. N. Van der Merwe

"A major shortcoming of the statistical back-analysis of coal pillar strength is that it relies on the asmined pillar dimensions, not taking into account time-related pillar scaling with subsequent reduction in pillar width. The paper describes an investigation where the rate of pillar scaling was applied to the pillars in the databases of failed and unfailed pillars. The reduced pillar sizes were then used in the same method of statistical back-analysis that had been used in the past.This resulted in an equation for pillar strength which predicts significantly greater pillar strength than the previous statistical analyses, which is similar to the strength which had been found earlier by direct testing of large specimens underground. It is concluded that the lower strengths found by previous statistical analyses are due to the incorrect pillar width being used and that by adjusting the pillar sizes to compensate for scaling, more credible results that correspond to direct testing are obtained.As the newly derived strength equation is time-dependent, it follows that the safety factors and probabilities of failure are likewise time-dependant. An equation to determine the probability of failure is also developed. This results in the safety factor being close to unity at a probability of failure of 50%, which is aligned to statistical expectation. IntroductionSince the Coalbrook mine disaster, caused by massive pillar collapse, there have been several attempts at analysing and defining the strength of coal pillars. It was realized in the very beginning that performing classical strength tests on coal specimens in a laboratory and then transferring those results to real coal pillars could not be successful. The scatter of results is one problem and, more seriously, there is a size effect (at least for small specimens) that made the transformation of strength results to much larger coal pillars underground all but impossible.Two main schools of thought then emerged. Some researchers preferred to perform direct strength tests on large specimens underground, while others relied on statistical back-analysis of failed and unfailed pillar cases, attempting to determine the differences in size and shape that would allow a satisfactory prediction of failure. The latter school of thought resulted in the method that was widely accepted by the South African coal mining industry, described in the landmark publication by Salamon and Munro (1967)."

Jul 1, 2019

By D. Chetty

Process mineralogy forms an integral part of geometallurgy, with ore body characterisation being but one piece of the puzzle in optimising value derived from ore. This value is not only financial, but importantly speaks to sustainability from environmental and social standpoints. The reactive approach of traditional process mineralogy is increasingly being replaced by predictive methods in the geometallurgical sphere, for which mineralogical information must be timeously acquired on judiciously selected sample sets to understand ore variability and its impact on orebody processing. Such processes are not only metallurgical, but must incorporate mining and waste management protocols. Dwindling resources like water and energy also demand innovative approaches for lowering consumption and/or promoting recycling along the value chain. Addressing such challenges relies on appropriate characterisation of ore behaviour under different process regimes. Coupled with this, emerging characterisation tools are increasingly applied to understand the mineralogy of unconventionallypresented and difficult-to-process ores to meet societal and technology demands. Such tools are often accompanied by the generation of large, computationally intensive datasets, for which data management and storage are key requirements, particularly when deciphering temporal trends in ore and process variability. This paper will elaborate on these themes with examples that highlight the importance of process mineralogy throughout the minerals value chain. Keywords: Process mineralogy, ore characterisation, geometallurgy

Jan 1, 2020

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By J. Thompson

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree A study into the stability of strike gullies at TauTona mine was to be carried out. In reaching the conclusions to follow, a three-stage process was followed. ?A literature study as well as discussions with management and workers alike to gain their inputs and perceptions. ?An ESH Department survey into the history of transgression from proper mine standard in TauTona strike gullies. Unfortunately records were found to be scarce and obscure and the importance of better inter-departmental recordings cannot be stressed enough. ?An underground survey of 11 pre-selected gullies distributed in both the UCL and LCL reef horizons. This stage is to carry the greatest weight in the points to be brought forward in this report. The process highlighted and ranked the following areas as the most critical role players in the deterioration of strike gullies: ?Poor blasting practice ?Sub-standard siding depth and lead-lags ?Split sets ?Off line gully development ?Adverse geological features. The following has been suggested to the mine to help reduce strike gully instability. ?Where possible, maintain lead-lags below 7 m?else increase the siding depth to suit. ?Decrease the gully width standard to 1.2 m (especially in ?high risk areas?). ?Discourage drillers from drilling side holes in gully face blast pattern. This will allow for time in which tendon support can be kept up to date. ?Ensure split sets are installed 1 m behind the gully face so as to prevent opening up of fractures. ?Utilize the centre split set in the 1:2:1 pattern to maintain the proper gully line. ?When adverse conditions prevail, it is necessary to apply a special support plan not only to the panel face, but also (just as importantly) to the gully as well. Shotcreting of the gully hanging is a suitable long-term consideration for providing the additional a real coverage needed. List of Abbreviations [CL Carbon Leader M/O Mine Overseer UCL Upper Carbon Leader FOG Fall of Ground LCL Lower Carbon Leader H/W Hanging Wall ERR Energy Release Rate F/W Foot Wall WDL Western Deep Levels ESH Environmental Safety and Health ]

Jan 1, 2002

By S. F. Burks

"This paper develops themes explained at two SAIMM platinum conferences. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can be increased significantly, usually even before the expenditure of significant amounts of project capital. Recent studies of NPV have aimed to simultaneously evaluate the impact of the optimized financial solution on the non-financial features of a project or operation.The case study presented comprised a commercially orientated review of the prefeasibility study designs and cost estimates of a platinum group metal (PGM) project in South Africa, followed by value chain optimization and sustainability studies of the project carried out simultaneously to identify potential value uplifts to be gained and guide the owners’ team going forward into the feasibility study phase. Some of the major aspects of the project that were found to have significant potential to add value included enhancement of the business model by the application of activitybased costing and theory of constraints, focus on the highest net value portions of the orebody in the early years of production, enhanced and optimized scheduling of the underground mining operation, application of dynamic grind and percentage mass recovery from ore to flotation concentrate (also known as percentage mass pull) to optimize revenue, application of elevated cut-off grades early in the life of mine, matching of the mining and processing capacity, expansion of the operation subject to capital availability, and installation of downstream processing facilities subject to regional third-party capacities.The investigation of non-financial project features focused on demonstrating that a financially optimized solution could also have a number of other benefits. These are mentioned briefly in the paper, which aims to present the status of the project at an early stage of its development."

Jan 1, 2016

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. C. D. Phillis

The annual mine planning process is one of the most important tactical/operational steps towards achieving strategic goals. These tactical plans are part of a very comprehensive Mineral Resource Management process, with the natural sequel to planning being execution. The execution of an underground hard rock mine plan is a multi-project environment that comprises many development-construction-equipping-stoping single project paths, which are referred to as ?stoping paths?. The uncertainty that typifies execution of projects comes in the form of untimely disruptions to constituent tasks and/or project paths. Annual mining plans also include quantified objectives for occupational health and safety, production, quality, cost, employee morale, environment, and corporate social investment. Such objectives make for a highly complex environment that management must contend with?complex in the sense that all the paths and objectives have interdependent constraints. Furthermore, at the time of this paper, Sections54*and 55**of the MHSA*** put the onus on management to ensure legislative adherence. It stands to reason that planning estimates allow excess capacity?buffers?that cushions the impact of untimely disruptions. This paper concerns the fact that despite all the buffers allowed for, time, scope, and budget creeps impact on mine planning and threaten its successful execution. As a consequence, the paper deals with buffer management, the essence of Critical Chain Project Management (CCPM). Effective buffer management provided strategic (executive level) updates without losing the tactical/operational detail necessary for job card creation, especially where professional skills and experience are in short supply. Indicative bottom-line results showed CCPM to be highly effective.

Jan 1, 2011

By F. S. A. de Frey

The main users of computerised financial evaluation tools in the mining industry are the mining investment analyst, the mine manager together with his financial manager and the mining student (undergruadate and post-graduate). The mining investment analyst's needs mainly centre around the-micro and macro aspects affecting the mining industry in general. The mine manager needs a tool to assist him with the planning, reporting and controlling of production, costs, efficiency, productivity and cashflow. For the mining student studying Financial Evaluation, the main need is for a computer program which will assist him in learning the basics of the subject. This paper concentrates on the needs and objectives of the course Financial Mine Evaluation, the approach to which is presented. Emphasis is placed on the practical computing sessions and the role of the FCS-EPS package as a training tool.

Jan 1, 1987

By R. A. Plumbridge

The Honourable Mr Molefe, Premier of the North- West Province; Or Scot-Russel, Chairman of the CMMI's XV Congress; Mr Loton, Chairman of the CMMI; distinguished guests, ladies and gentlemen. At the outset may I express my sincere appreciation to the organisers of this Congress for their kind invitation to me to participate in the plenary session. May I also thank the CMMI for inviting me to be their fifth distinguished lecturer. This is a signal honour and one which is sincerely appreciated by my Group and myself. The subject of gold is a very emotive one. It conjures up different images in the minds of a wide variety of people. For many of us it is very simply the ultimate metal. In ancient times gold was sought after and treasured; it was the chosen metal for adornment and many of the best preserved artefacts of that time were hand-fashioned from gold which had been won by primitive mining techniques. Gold's rarity and its value was recognised by those who fashioned the earliest gold coins thus underlining gold's special place as a store of value.

Jan 1, 1994

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016