Search Documents

By A. Cáceres, L. Navarro, N. Altmann, R. Betinol

Copper concentrate is produced in Chile in the high Andes and transported to the coast for shipping through long distance pipelines. The pipeline and fittings installed have to withstand the high abrasion and corrosion environment of the copper concentrate. To protect the inside tube wall against corrosion, high density polyethylene (HDPE) liner is used. While HDPE liners can protect the steel wall against corrosion, it has also been assumed that the low surface roughness of the HDPE liner also inhibited incrustation caused by calcium carbonate and sulphate deposition. Recent events have indicated otherwise in a couple of concentrate pipelines for which BRASS has provided consultant service. This paper delivers a case study which includes (i) formation of incrustation and adhesion to HDPE liner, (ii) the detection of the incrustation through hydraulic analysis, (iii) the mechanism of removal of incrustation, and (iv) the catastrophic effects of their presence in an emergency situation.

Jan 1, 2007

By A. N. Brown

Rock breakage by drilling and blasting is fundamental to every hard-rock mining operation. The subject was an apt choice for a mining school because many technological changes have taken place since the subject was last presented some ten years ago. However, because of the development of surface mining, it was decided that two schools should be held: one for underground mining, and the other for surface mining. The School on Underground Mining was held at the University of the Witwatersrand in February 1986.Copper 87 COPPER 87 is an international conference organized by metallurgical and academic institutions of two of the largest producers of copper in the world, Chile and Canada.

Jan 1, 1986

By R. T. White

The usual figures quoted for water usage in South African gold mines are 1 ton of water used per ton of rock broken, which represents a consumption of 4000 litres of water every second. Owing to the limited sources under ground water, the high cost of surface-water supplies, and the environmental problems of effluent disposal, water IS recycled continuously for underground use. This paper reviews the various types of water treatment and why water needs to be treated. The uses of lime and some flocculants are considered, since much of the mine service water requires only simple neutralization and clarification. Where mining depths necessitate the installation of underground refrigeration plant, more stringent water requirements must be met, and where plant performance is to be maintained, the prevention of system scaling and corrosion is necessary. The families of chemicals added to provide such protection are outlined, together with a description of the mechanisms of control.

Jan 1, 1985

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By J. D. Koch

The past ten years or so have seen many changes in the methods and approach adopted for projects in the metallurgical and mining industry in South Africa. These changes have led to an increased use by operating companies of the project and construction management services offered by engineering contracting companies. For a variety of reasons, this development has been slower in the metallurgical industry than in other areas of production, but that industry is also now showing an increasing trend in this direction.

Jan 1, 1981

By B. Strohmeier

An account is given of the use of a computer to control the performance of three ultra-high-powered electric-arc furnaces in Iscor 5 steelmaking plant at Vanderbijlpark, South Africa. Several of the reports and graphs printed by the computer are reproduced.

Jan 1, 1985

By N. Gibson

The application of oxygen in a copper smelter by N. GIBSON* (Visitor) This paper describes how the problem of increasing the capacity of the Rokana copper smelter was handled, and how oxygen was found to be technically and economically the best solution. The first phase of its implementation is outlined.

Jan 3, 1974

By B. C. Alberts

Rapid and effective handling of run-of-mine, waste, and treated materials is vita.! to every step of resource development and recovery. Modern mine managements have planned and engineered systems for the handling of ever-larger tonnages. Where traditional methods have not proved to be costeffective and adequate, managements have pioneered the development of new materials-handling systems in the mining industry.

Jan 1, 1983

The 8th Annual University of Cape Town (UCT)/ University of Stelenbosch (US) Minerals Processing Symposium was held at the Van Riebeeck Hotel in Gordon's Bay on 3rd August, 1990, under the auspices of the Western Cape Branch of The South African Institute of Mining and Metallurgy. The primary object of this meeting was to give research students at UCT and US the opportunity to present their work to a critical audience from industry, and to obtain feedback regarding the research needs of the minerals industry. Although the emphasis of these symposia is on work in progress at US and UCT, they also create an excellent opportunity for informal discussion between academics and metallurgists in industry. The first symposium in this series was held in 1982 at US, while the symposium in 1989 was replaced by the International Colloquium on Developments in Froth Flotation, also held in Gordon's Bay.

Jan 1, 1990

By Y. G. Che, M. Brown, R. L. Gandhi, M. D. Watson

Slurry pipelines have proven to be an economical method of mineral concentrate transport over long distances. Some of these pipelines are internally lined with high-density polyethylene (HDPE) to avoid internal corrosion. HDPE is an inert and extremely smooth material, and it was believed hat scale deposits would not form on it. However, there have been instances of scaling on HDPE lined pipes. Scale problems have also occurred on bare steel pipes. In this paper experience with scale problems in some of these pipelines will be summarized. Alternatives available for control of scale problems will be discussed, and a success story for the control of scale problems in the 300 km long Century zinc and lead slurry pipeline will be presented.

Jan 1, 2007

By H. A. D. Kirsten

The skills differential between manpower supply and demand is due to deeply rooted socio- and politico-educational misconceptions that can be remedied only by a concerted cooperative effort on the part of the general public, the State, organized industry, organized engineering, and engineering education. This will require the general public to recognize that the reasons for the shortages in engineering manpower should be regarded as critical. Public perceptions of engineering, of the vocational and educational prospects in engineering, and of the skills required are poor. The spectrum of engineering vocations, the corresponding function profiles, the interaction between the vocations and the relative proportions of the vocations in the engineering team are in general not adequately appreciated. The recruitment and training of students and teaching staff, teaching facilities, educational curricula, practical training, qualifications, professional registration, and financing are aspects of engineering education that should be brought to the attention of all concerned. . In addition, the educational curricula for the various vocations need to be specified clearly and definitively if the overall mission of engineering education is to be properly appreciated. The uncertainties between university and technikon education and the pursuant vocations need to be resolved. This can be done only by defining the respective curricula in terms of the mental skills and scientific techniques required. The remedial actions with regard to the rationalization of engineering education comprise informing of the public; establishment of an active political lobby; revision of existing education policy; rationalization of existing educational infrastructure; promotion, development, and guidance of engineering student intake; financing of engineering education; accelerated creation of new employment opportunities; and monitoring of the supply and demand of high-level manpower. The parties required to nitiate these remedial actions are various State departments and corporations involved in engineering and industry, various departments of education, the Directorate of Technology of the Department of Trade and Industry, organized engineering education, organized engineering, organized industry, and the Human Sciences Research Council. Only if these interest groups actively initiate the various actions under the coordinated guidance of organized engineering wil the required results be achieved. The South African Engineering Association has proposed a comprehensive programme as strategy to solving the problem, and has obtained broad consensus from various State departments, organized engineering education and research, and the private sector. A joint venture between the Foundation for Research Development, the South African Engineering Association, and organized industry has been charged by the State President with the task of launching the programme.

Jan 1, 1991

By N. B. Strydom

The data on heat stroke cases reported during the past five years were examined to determine the influence of age on the incidence of heat stroke. Relating the age distribution of these cases to that of the total number of Bantu mine workers showed clearly that the older men run a significantly higher risk of developing heat stroke than the younger men. Although the number of Bantu over 40 years of age in the industry is less than 10 per cent of the total they nevertheless accounted for 50 per cent of the fatal heat stroke and 25 per cent of the nonfatal heat stroke cases during the period under review. Age must, therefore, be recognised as a causal factor in heat stroke and the worker over 40 years of age should be allocated to work on surface, or in cool areas or to non-strenuous and supervisory tasks in hot areas.

The sixth University of Stelenbosch (US)/University of Cape Town (UCT) Minerals Processing Symposium was held at the University of Cape Town on Friday, 7th August, 1987, and was sponsored by The South African Institute of Mining and Metallurgy (SAIMM). Once again the Symposium attracted a large number of delegates from the mining, metallurgical, and chemical industries. Uranium and electricity A symposium on 'Uranium and Electricity- The Complete Nuclear Fuel Cycle' will be held in Saskatoon, Canada, during 18th to 20th September, 1988. The Symposium is sponsored by the Canadian Nuclear Society. Electric steel The Institute of Metals, organizers of the 3rd European Electric Steel Congress, have announced that this important international event will take place in October 1989 at the Bournemouth International Centre.

Jan 1, 1987

By L. Dison, J. A. Hahn, G. E. Blight

A system of artificial support for shallow mines is described, analysed, and evaluated. The system can be designed rationally to support a predetermined overburden load, and tests have shown that the design theory gives accurate predictions of strength. The support system, consisting as it does of two basic materials, reinforced granular material and reinforced cemented material, is flexible and can be varied to suit changing requirements of height and load. The system of preloading to the design load by jacking off the roof ensures that the walls are both stiff and prooftested.

Jan 1, 1982

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

By J. H. Bulloch

A study of fatigue-crack growth in a rail steel and an associated weld metal showed that fatigue cracks in the deformed rail steel had slightly higher growth rates than in undeformed rail steel. The crack growth in the weld metal was appreciably faster than either and exhibited plateaux that were above the upper bound reported for rail steels, The cyclic-life curves showed that, over an indicated service period of 8 years, both the deformed and the undeformed rail steels should not be prone to fatigue failures under the defined mechanical conditions, For the weld metal, the cyclic-life curves indicated the possibility of premature fatigue failures but, as al the input parameters represented a 'worst case' situation, this assessment could wel be ultra-conservative. In the rail steels at low levels, the extension of the fatigue cracks occurred by ductile striated growth. At a Kmax level of 35 MPa .J/n, cleavage facets formed initially on the surface of the fatigue fractures, and their incidence increased with Kmax until the onset of fast failure, The microstructure of the deformed rail steel exhibited cleavage facets at a slightly lower Kmaxvalue, and contained more cleavage facets at a given K level, than the microstructure of the undeformed rail steel. The average size of the cleavage facets agreed well with the pearlite nodule dimensions of 60 to 100 ILm. The microstructure of the weld metal was much coarser and contained columnar grains. At al f.K levels, the dominant fracture mode was cleavage, with small isolated regions of ductile striated fatigue cracks. The size of the cleavage facets varied from 150 to 600 ILm, and such a variation may be explained by the fact that cracking generally occurs in association with the pro-eutectoid ferite phase, and that this phase is distributed along some boundaries of prior austenite grains and the boundaries of the coarser columnar grains.

Jan 1, 1987

By K. Kabezya

A study on slag dispersion in a model of bottom-blown bath smelting converter was undertaken at room temperature. The aim was to investigate the behaviour of the dispersed slag phase at various operating conditions with very high gas flow rates in low slag volume (10%) systems. For simulation purposes water, paraffin-oil, and air were used to represent the bulk steel, molten slag, and gases respectively in a one-fifth cold model of the commercial 100 t Creusot-Loire-Uddeholm (CLU) converter used in the manufacture of stainless steel in South Africa. Dimensional analysis was done to correlate mathematically the dispersed phase holdup with the operating conditions and the modified Froude number. The overall expression of the holdup revealed that the dispersed slag phase decreased with the vertical distance from the original interface between the liquid phases. The dispersed phase also decreased with the radial distance in the water plume zone toward the sidewall. The holdup was apparently much higher on the side of the reactor where there were no tuyeres. The modified Froude number ensured the correlation between the model and the prototype.

Jan 1, 2014

By T. Feroze, B. Genc

"The ventilation of underground coal mines plays an important role in minimizing the risk of methane and coal dust explosions. The ability of ventilation, with the use of line brattices (LBs), to remove methane and coal dust in empty headings is dependent on the amount of air leaving the LB and entering the heading. The quantity of this air depends on the associated system variables, namely heading dimensions, settings of the LB, and velocity of air in the last through road (LTR). However, the exact effect of these system variables on the flow rate at the exit of the LB in an empty heading is not known. The installation of LBs in South African coal mines is generally carried out based on experience. This can result in overor under-ventilation and may increase the cost of providing ventilation or cause accidents, respectively. In this paper, using computational fluid dynamics (CFD), the air flow rate at the exit of the LB in an empty heading was estimated using full-scale three-dimensional models. The CFD model used was validated using experimental results Firstly, the settings of these three system variables were varied, the flow rates at the exit of the LB were measured, and finally the results were used to calculate the effect of each system variable. The outcome is a mathematical formula that can be used to estimate air flow rate at the exit of the LB in empty headings for any practical scenario.This paper will help the coal mining sector in South Africa by providing estimation models based on scientific reasoning for the installation of LBs, and will also serve academia as part of the curriculum towards educating future mining engineers."

Jan 1, 2016

By K. R. Vost

Most theoretical methods for the prediction of air-temperature gradients in underground airways always assume that the temperature of the entering air either remains constant or has only a slow seasonal variation. Large changes of temperature, caused by variations in atmospheric conditions on the surface, were measured in a fourteen-day period in air entering a horizontal airway. The changes in wet-bulb temperature were damped along the airway less uniformly than the dry-bulb changes; significant variations occurred in the wet-bulb temperature of the air leaving the airway. The damping was .associated with large variations in air-temperature gradients. Other causes of rapid changes In temperature are discussed. These changes must be taken into account in predictions of the frequency with which undesirable conditions can be exceeded at critical points in the ventilation circuit of a mine to allow proper planning of ventilation and refrigeration requirements.

Jan 1, 1977

By J. A. L. Napier

SYNOPSIS Many tabular mining problems can be modelled effectively by displacement-discontinuity techniques, which can be extended directly to represent fracturing on discrete planes and movements on planes of weakness. This paper presents a unified method for computing the energy changes that occur when multiple discontinuities intersect and are extended incrementally. It shows how this method can be used to deduce energy-release information for standard layout problems and, in addition, how the technique can be incorporated in numerical procedures based on the displacement-discontinuity method. Examples are given to demonstrate the effects of off-reef fracturing and the importance of stope-fault intersections during seismic events.

Jan 1, 1991