Search Documents

By X. Ndlovu

Underground observations in a coal mine have indicated failure oft he immediate roof above the bords. Careful observations and photographic recording of occurrences of these roof failures, termed ?roof guttering?, have been made. The occurrence of guttering results directly in roof instability, and indirectly, due to the interaction of the guttering with natural planes of weaknesses in the immediate roof rock. In this paper, relevant observations of roof guttering, possible mechanisms of formation of roof gutters, laboratory testing for determination of material strength and deformation properties, and numerical analyses to explain underground observations are described. Mapping of roof failures showed that these took place mainly towards the centre of the roadways. Roof guttering was observed often to occur violently and with little warning. Occurrence of roof guttering has a negative impact on production?some panels are abandoned, production times are increased and safety of workers is compromised. The numerical stress analyses showed that, although none of the constitutive behaviour criteria used predicted the observed underground failures correctly, the extension strain criterion gave the best agreement.

Jan 1, 2007

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

By C. C. Pretorius, S. Ramjee, R. J. Mostert

The study investigates the effect of prior corrosive exposure on crack growth resistance behaviour of thin sheet (3 mm thick) aluminium alloy 2024-T3 at slow strain rates. Compact tension specimens were exposed to standard corrosive environments that simulate accelerated atmospheric corrosion attack. Two corrosive environments were considered – an exfoliation corrosion (EXCO) solution and a 3.5 wt% sodium chloride solution. The unloading compliance R-curves of the two-hour EXCO-exposed specimens revealed a significant degradation of approximately 11% in the crack growth resistance behaviour (Kc_e values) compared to the baseline (air-exposed) values. Furthermore, secondary intergranular crack formation was also revealed in the plastic zone ahead of, and adjacent to, the crack tip of these specimens; which formed during the crack growth resistance loading. It is postulated that the observed degradation of the Kc_e values of the EXCO-exposed material is due to hydrogen embrittlement since the exposure times for the EXCO evaluation were limited to ensure that uniform corrosion dominated; that is, significant penetration of corrosion damage and pitting due to localized corrosive attack did not occur. The sodium chloride-exposed specimens revealed a similar degradation (13%) after 24 hours exposure. However, slight intergranular corrosive attack and isolated pitting were observed on the exposed surfaces prior to crack growth resistance loading, resulting in notch effects that could assist in crack growth. Pitting and intergranular corrosion were, however, not observed at the pre-crack tip. The relative contributions of the notch effects and the hydrogen embrittlement during the degradation of the KR performance are, therefore, unclear.

Apr 1, 2021

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By S. O. Choi, C. Park, C. Sunwoo

Two methods of stress measurements have been executed on the surface and underground to con-struct an oil storage cavern using hydro-fracturing and overcoring method. The first measurement has been performed to make a design of the caverns before excavating and the second to confirm the stress state during excavation. Six measurements have been carried out in the hydro-fracturing test at the depths between –17.8 and 54.5m from the sea level and a single measurement in the overcoring test in a single borehole at the depth of –21m from the sea level. The ratios of the maximum horizontal to vertical stress measured using hydro-fracturing and overcoring method are 2.95 and 3.1, respectively. Also, the orientations of the maximum horizontal stress are N53E and N58E. These measurements show that both methods give almost same results and significant horizontal stresses are acting on this cavern. Deux méthodes de mesure de contrainte ont étè exécutées sur la surface de terrain et sous la terre pour construire une cavité de stockage de pétrole en utilisant l’hydro-fracturing et l’overcoring. La première mesure a étè faite pour le plan des cavités avant l’excavation et le seconde pour con-firmer l’état de contrainte durant l’excavation. Six measures ont étè faites dans le teste de l’hydro-fracturing à la profondeur entre –17.8 et 54.5m depuis l’élèvation maritime. Une seule mesure a étè faite dans le teste de l’overcoring dans une seule trou de songdage à la profondeur de –21m. Le ratios de la maximale contrainte horizontale à la contrainte verticale mesure par les deux méthodes sont 2.95 et 3.1, respectivement. Les orientations de la maximale contrainte horizontale sont N53E et N58E. Ce montre que les deux méthodes donnent presque m me résultats et la contrainte im-portante est activée sur ces cavités. Zwei Druckmessungen wurden durchgeführt auf der Erdoberfläche und im Innern von Ölspeicher-kavernen unter vergleichender Anwendung des Hydrofraktionierungs- und des Kernbohrungsver-fahrens. Die erste Messung wurde durchgeführt um einen Plan der Kavernen vor der Herstellung zu erstellen und die zweite um die Druckverhältnisse während der Bohrung zu überprüfen. Sechs Messugnen wurden mit der Hydrofraktionierungsmethode bei einer Tiefe von 17,8m und 54,5m unter dem Meeresspiegel und eine einzige Messung mit der Kernbohrungsmethode in einem Bohr-loch bei einer Tiefe von 21m unter dem Meeresspiegel vorgenommen. Das Verhältnis von maxi-malem horizontalem zu vertikalem Druck bei der Hydrofraktions- und der Kernbohrungsmedthode ist 2,95 bzw. 3,1. Die Bezugspunkte des maximalen horizontalen Drucks in beiden Verfahren sind N53E und N58E.

Jan 1, 2003

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

By M. S. Shishvan, J. R. van Duijvenbode, L. M. Cloete, M. W. N. Buxton

Geochemical and mineralogical datasets from Tropicana Gold Mine, Australia, have been used to define ore fingerprints. VNIR/SWIR spectral data were represented by four normalised wavelength regions and were clustered to form spectral classes. Sequentially, these spectral class proportions within a block and collocated XRF data were clustered to form material types (fingerprints). The material types were related to an Equotip-BWi correlation. These correlations can be used to extrapolate a hardness signature and generate a BWi proxy for different blocks. The combined fingerprints and BWi proxy can assist as a tool for enhancing the prediction of comminution behaviour. They can explain specific domain-related hardness variations. For example, one material type could be separated into a softer (~15-18 kWh/t), and harder (>20 kWh/t) material blend. This was accomplished using the commonly overlooked VNIR region at 605 nm. This outcome has significance for blending strategies.

Sep 1, 2021

By FT Cawood

The latest Draft MPRRB was released for public comment in October 2006. The main purpose of the Bill is to collect royalties at mines developed in terms of new-order mineral rights granted through the MPRDA process. The transition phase stipulated in the MPRDA will be completed by 1 May 2009, on which date mineral royalties will become payable to the state. The royalty rates stated in the MPRRB differ from mineral to mineral and also depend on the degree of refinement. Gold is the subject of this paper, where the royalty rate ranges from 1.5% (for refined gold) to 3% (for unrefined gold) of sales revenue. This royalty is payable regardless of profit, with a maximum 75% relief for loss-making mines. The purpose of this paper is to establish whether or not it would be necessary for gold mines to adjust their mineral reserve statements as a result of this Bill. The methodology is to add the royalty costs stipulated in the MPRRB to the actual quarterly information for the past ten years as reported by the gold-mine members of the COM. The rationale is to investigate the impact this Bill (in its current form) would have had on gold reserves that must be left unmined in the ground because of a higher pay limit. The results of the study point to a significant impact on reserves available for mining with the subsequent shortening of mine lives and retrenchment of workers. Had the MPRRB been effective for the 10 years prior to 1996, it would have resulted in 46 tonnes of gold being sterilised. Stated alternatively, 30 700 workers at COM gold mines alone would have lost their livelihoods.

Jan 1, 2007

By F. Nakhaei, A. Noury, S. Ghodrati

To achieve maximum efficiency in any purification stage, the flotation should be continued until the concentrate grade reaches the feed grade. During sampling from rougher cells of the Iranian Sarcheshmeh copper concentrator plant 1, it was revealed that the concentrate grade of the last five cells of rougher circuit was close to feed grade. Therefore, it was suggested that the concentrate of the aforementioned cells be mixed with rougher feed. In this study, one of eight rougher circuit rows was selected and evaluated. The floatability tests were performed to compare the flotation behaviour of rougher feed and mixture of concentrate of the last five cells with rougher feed in the laboratory scale by a tree analysis process. The results showed that mixing of rougher last five cell concentrate with feed has a detrimental effect on flotation efficiency that leads to a 3% decrease in recovery. It was also observed that with grinding of this concentrate, recovery can be improved. Keywords: Efficiency, flotation, rougher, tree analysis, floatability, concentrate, mixing

Jan 1, 2020

By C. W. Siyasiya

Process and steel chemistry differences in hot rolled Al-killed low carbon strip steel between the hot charge route (HCR) as practised in a compact strip production (CSP) plant and the conventional cold charge route (CCR) have been studied. This was done with reference to differences in reheating practice, hot rolling practice and steel chemistry through emphasis on the effects of solubility and reprecipitation of AlN in the two process/product combinations and its effect on ferrite grain size development. An earlier modelling study on the evolution of the austenite grain size in both of the above hot rolling processes has also now been extended to include an estimate of the possible effects of retained strain after the last finishing pass on the ferrite grain size. As part of this study the equilibrium solubility trends of AlN in a number of boron-free low carbon Al-killed strip steels with low and high sulphur content from the two respective processes was investigated by the thermoelectric power (TEP) technique and differences in the effects through the derived solubility equation of Log[Al][N]=2.6?9710/T at typical slab reheating temperatures was demonstrated. Ferrite grain size modelling using the significantly lower Ar3 transformation temperatures generally found in hot rolled low carbon strip steel produced in the CSP plant using the HCR compared well to the larger grain size produced in the conventional CCR strip rolling plant. Keywords: austenite grain size modelling; thermoelectric power(TEP); compact strip production (CSP); cold charge route (CCR);ferrite grain size

Jan 1, 2008

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By F. S. Hoseinian, B. Rezai, E. Kowsari, M. Safari

In order to remove heavy metal ions from a large volume of wastewater with a low ion concentration, ion flotation appears to be promisingly effective. In the ion flotation process, because of the high ion removal percentage, the amount of water recovery percentage is a very important factor which determines the process efficiency. However, ion flotation suffers from relatively high collector concentration to achieve the high removal percentage to the desired limit, which subsequently increases the water recovery. In this study, functionalised graphene oxide (FGO) was synthesised, using a chemical method in the ion flotation process, applied as a collector for increasing process efficiency by reducing the collector consumption and water recovery. The high ion removal was achieved with both collectors of sodium dodecyl sulfate (SDS) and FGO, while the water recovery with a collector of SDS was 3.4% higher than that with a collector of FGO. The results indicated that the FGO could be effectively used for high ion removal and low water recovery in the ion flotation process. Keywords: Ion flotation, synthesised collector, ion removal, wastewater, water recovery

Jan 1, 2020

By R. Kumar, N. R. Mandre

"The beneficiation of iron ore slimes by selective flocculation was studied. Polyacrylamide (PAM) and guar gum were used as flocculant, along with sodium hexametaphosphate (SHMP) as a dispersant. The samples collected were initially subjected for chemical and mineralogical studies. The mineralogical studies indicated the presence of haematite and goethite as the principal iron-bearing minerals, with quartz and kaolinite as gangue minerals. The selective flocculation tests showed that the Fe grade can be enhanced from 58.24% to 64.60% Fe at a recovery of 66.33% using polyacrylamide as the flocculant. A Fe grade of 63.20% at a recovery of 68.04% was obtained using guar gum as flocculant. The efficacy of the studies was analysed using a separation index, which indicated that the higher separation index was obtained with the tests employing polyacrylamide as the flocculant. IntroductionIndia is endowed with huge reserves of highgrade iron ore and is one of the prominent producers in the world. As the high-grade iron ores have been exhaustively mined, it has become imperative to use low-grade iron ores, fines, and slimes to meet the growing demand. Also, generation of fines and slimes during mining and processing contributes to loss of minerals to the extent of 30% of the total value (Mandre and Panigrahi, 1997). These fines/slimes are often discarded as waste into tailing ponds, containing considerable amounts of iron. Therefore beneficiation of tailings/slimes has become necessary for optimal utilization of the resources.In recent years, interest in recovery of valuable minerals from low-grade ores, slimes, and tailings has increased worldwide. These activities are initiated not only to recover minerals but also to address various environmental issues associated with fine particle treatment. The literature reveals that several technologies have been employed in this regard, including flotation, advanced gravity separation, and high-intensity magnetic separation. However, these processes are found to be ineffective for fine particle treatment due to lower collision probability in flotation, decreased gravitational effect in gravity separation, and reduced drag force in magnetic separation, among other factors (Batisteli and Peres, 2008; Das et al., 2007; Dworzanowski, 2012; Rocha, Caneado, and Peres, 2010). Therefore, it is in this regard that selective flocculation has gained importance in treating slimes in recent years."

Jan 1, 2017

By M. G. Maruma, L. A. Mampuru

"Mill liner wear is a major cost item in the mining industry and there is continuous research to prolong the life of the liners. Over the years it has become apparent that even though high-chromium white cast irons are highly efficient as abrasion-resistant materials, a combination of wear resistance and fracture strength remains difficult to achieve. Increasing the hardness of the high-chrome white cast iron (HCWCI), which improves the resistance to abrasion wear, is often accompanied by a deterioration in fracture strength. Operational conditions inside the mill require that the liner should be made of highly wear-resistant material with some fracture strength. Vanadium additions ranging from 0.2 to 3 wt% were made to HCWCI in an attempt to refine the microstructure. It was found that an increase in vanadium content promotes grain refinement. A content of 1.5-3 wt% gave the best results as measured by the maximum breaking strength.IntroductionOver the years it has become apparent that even though high-chromium white cast irons are highly efficient abrasion-resistant material, a combination of excellent wear resistance and fracture strength remains difficult to achieve. The exceptional wear resistance of highchromium white cast iron (HCWCI) is attributed to hard chromium carbides embedded in an austenitic/martensitic/pearlitic matrix. When the chromium contents exceed 12 wt%, interconnected MC3-type carbides of conventional cast irons are replaced by rodshaped and isolated M7C3 carbides (Powell, 1980), leading to an improvement in the impact toughness, ductility and fatigue resistance. However, the main M7C3 carbides in HCWCI are hard and brittle and can provide an easy path for crack propagation. This limits the applications of HCWCI, particularly in severe impact conditions. Most operations involving HCWCI are in crushing and grinding and the life of a part/liner is limited by its wear resistance. However, improving the wear resistance of HWCI comes at the cost of a significant reduction in fracture strength. Concerns about premature failure of HCWCI mill liners in the mining industries prompted a study to improve the wear resistance and mechanical properties of HCWCI."

Jan 1, 2016

By H. M. Friede

Iron Age metal working in the Magaliesberg area by H. M. FRIEDE, Ph.D. (Visitor) Evidence of smelting and metal working in the Magaliesberg comes mainly from three sites: Broederstroom (Pretoria District). Uitkomst Cave (Krugersdorp District), and Olifantspoort/Olifantshoek \Rustenburg District). The analyses of copper ores found at or near these sites are reported. as are the analyses of twenty-six samples of slag from the Magaliesberg area and other sites in the Transvaal. Iron implements and copper ornaments found at the Magaliesberg sites are described. and the analyses of some of these specimens are reported and discussed. A metallographic report on two iron objects from Broederstroom points to similarities in the smelting and forging techniques that were practised in the Transvaal and Nigeria during the Early Iron Age.

Jan 6, 1977

By A. Becker, R. Tait, S. L. George, A. Carlisle

Surface treatments like laser shock peening (LSP) induce residual stresses penetrating up to 1 mm deep, surpassing traditional methods, thus significantly increasing the potential impact on materials prevalent in the automotive and aerospace sectors. Through extensive fatigue testing and fractography investigations, it was determined that LSP resulted in a fatigue life increase of over five times for aluminium alloy AA7075-T6 and titanium Ti-6Al-4V. Increased fatigue life was also noted in AISI316 stainless steel, which showed increases in fatigue life of 1.7x. While fatigue life in all cases improved, the efficacy of LSP was shown to be material dependent.

Jul 23, 2025

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

The inherent weakness of the Zincor and similar iron removal processes is the relatively high undissolved zinc loss associated with the iron residue. High soluble zinc losses also occur due to poor filterability of the iron residue even though it may be limited to intermittent events. This work focussed on defining the optimum operating window for the Zincor iron removal process where iron is mainly removed in the form of amorphous, intermediate iron phases such as schwertmannite and ferrihydrite. In terms of the main operating conditions, optimum filterability was achieved under the following conditions: pH of 3.0, temperature as high as practically possible (70C), at least 25 kg/m3 seeding, and a retention time of at least 4 hours. When increasing the temperature from 60C to 70C, the required residence time decreased by almost 50%. Undissolved zinc loss was also reduced from 8% to between 2% and 3% by using a basic zinc sulphate/zinc oxide mixture as neutralising agent to effect iron removal.

Jan 1, 2003

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012