Search Documents

By H. Ding

Calcium carbonate/Titanium dioxide composite, characterized by coating TiO2 on the surface of CaCO3 particles, is an important substitute for titanium dioxide. This paper studies preparation method of CaCO3/TiO2 ,composites based on mechano-chemical effects, measures its properties as a pigment, analyzes the binding form and interface reaction mechanism between CaCO3 and TiO2. Through single finely grinding of CaCO3, co-grinding of CaCO3 together with TiO2, and mecha-no-chemical effects produced in the course of grinding, CaCO3/TiO2 composites can be prepared successfully. Results indicate that grinding fineness of CaCO3, co-grinding time of CaCO3 and TiO2, the weight ratio of grinding media to mineral feeding, and the amount of TiO2 have much influence on the properties of CaCO3/TiO2 composites. CaCO3/TiO2 composites have the properties same as titanium dioxide pigment, oil adsorption and ultraviolet adsorption same as TiO2, and 90% of hiding power as that of TiO2. Wet grinding of CaCO3 causes the production of mechano-chemical effect and hydroxyl group, through which CaCO3 and TiO2 can be bonded together. Repulsion occurs between the particles of CaCO3 and the particles of TiO2, respectively, they are both in good dispersion. But attraction occurs between CaCO3 and TiO2. TiO2 particles are distributed evenly on the surface of CaCO3. Therefore, coating of TiO2 on the surface of CaCO3 particles and chemical bond between them make CaCO3/TiO2 compo-sites have pigment properties of Titanium.

Jan 1, 2014

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By Å Sandström

Loussavaara-KiirunavaaraAB?s (LKAB) iron ore mine, Kiirunavaara, is of magnetite type and associated with apatite, a calcium phosphate mineral. Rare earth elements (REE) have been found in connection with the apatite but also in other minerals. An apatite concentrate was produced by flotation, in order to investigate the possibilities to extract REE from the apatite by hydrometallurgical means. The content of rare earth elements calculated as oxides (REO) was 0.44% in the concentrate. Initially, leaching was done with large excess of sulfuric acid, hydrochloric acid, and nitric acid to study the REE solubility with different acids. In sulfuric acid, the leaching recoveries of the different REE varied between 35% and 69%. The reasons for the relative low recoveries, were that the rare earth elements precipitated together with huge amounts of gypsum, that was formed during leaching. However, both hydrochloric- and nitric acid gave almost complete extraction of the REE into solution. Analysis of the small leaching residue obtained, revealed, that mainly the light REE remained in the residue indicating that a small part of the light REE were present in the concentrate, in some acid, insoluble mineral other than apatite. With the aim to separate the REE from the phosphoric acid, the solutions from hydrochloric- and nitric acid leaching were neutralized to a pH of approximately 2 with ammonia. During neutralization, REE were precipitated as phosphates with good recoveries and a concentrate of 10.5% REO suitable for further upgrading was obtained, while the remaining solution can be used for fertilizer production. In further solvent extraction studies, it was shown, that after re-dissolution the REE could be effectively extracted by Cyanex 923, thus allowing for purification from calcium and phosphate ions. The REE were finally stripped from the organic phase and a REE nitrate solution was produced. Keywords: apatite, rare earth elements, REE, leaching, solvent extraction, cyanex 923

Sep 1, 2012

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By G. Y. He

The large-scale 8.53m×3.96m (28?×13? F/F) SAG mills was first applied in Donggua Hill Copper Mine which processes 13,000 tons ore per day. The crushing and grinding circuit went into operation in the Donggua Hill plant in October 2004. However, at the beginning, the productivity of grinding only reached 58% of the capacity expected and some indexes of the crushing and milling circuit didn?t meet the requirements. Especially, the total load of the 8.53m×3.96m (28?×13? F/F) SAG mills was up to 34%~41% (25%~30% designed)and some hard rocks with the size of 25~70mm, which can?t be treated as a medium or even would be crushed and make larger ores or steal balls necessary, were seriously accumulated in the SAG mills. Consequently, they occupied the effective mill volume which in turn reduced the efficiency of the SAG mills and increase the energy consumption. In order to solve the problem of accumulation in the SAG mill and increase its productivity, some measures were taken, such as passing more hard pebble through the grate at mill dis-charging end, changing the type of steal balls and so on. And the results showed that these measures functioned well and had good effects, which is that the filling percentage of the SAG mills has been reduced to 26%~29% from 34%~41% with the composition of particle sizes improved a lot and the productivity increased by 77.4% reaching up to 13,380 tons per day.

Jan 1, 2014

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By L. S. Zhou

Germany-made AFX-100 multi-grade fluidized classifier, with exquisite built-in structure and unique novel design, materializes not only advanced and efficient classification, but also precise particle distribution and safe operation, in addition to lower energy consumption and operational cost. It, simultaneously in place of screw grader, water cyclone, and fine mesh sieve, is equipped with multi-function, and indicates superior advantage in comparison with other else grading facilities. As the third-generation equipment, which is efficient and modern, it, in China and therefore all over the world, will find wide application in processing both fine and ultra-fine iron ore resources. Industrial test, carried out in Benxi Steel?s Waitoushan Iron Mine, shows efficient classification, i.e., ?74µm particle contents in coarse, medium and fine products come to 6.09%,11.82% and 82.73%, respectively, while qualitative and quantitative efficiencies end up by 74.38% and 87.66%, respectively. Its separation efficiencies amount to 2.2 times as many as spiral classifiers, 1.8 times as hydrocyclones, and 1.3 times as vibration high-frequency fine screens. Another industrial test, which was practiced in Anshan Steel?s Donganshan Sinter Plant, indicates that classification qualitative efficiency comes to 65.06%, equal to 1.51 times as many as hydrocyclones; yield, 55.79%; -71µm particle contents in medium and coarse products, 42.02%; -71µm content in fine product, 95.42%; and concentration, 12.33%. Estimated separation indexes are as follows: Yield for concentrate at 31.22%, up 0.22% than that from general processing line; concentrate grade at 66.42%, up 1.13%; recovery ratio comes to 65.84%, up 1.28%, which, based on pilot study, results in 20 million yuan of economic return for Donganshan Floatation Plant.

Jan 1, 2014

By Evvie Chockalingam

Acid mine drainage (AMD) is a perennial problem particularly in abandoned mines, occurring due to the oxidation of sulphidic mine wastes. AMD is usually characterized by high concentration of dissolved metal ions, sulphate and low pH. The efficacies of substrates such as rice husk and the bark of Eucalyptus tereticornis (Sm.) are assessed for the removal of metal ions such as iron, zinc and copper from acid mine water obtained from an abandoned copper mine. Over 99 % of Fe, 98 % of Zn and 95 % of Cu removal could be achieved from acid mine water, with a concomitant increase in the pH value by three units using rice husk as an adsorbent. With respect to tree bark as an adsor-bent, about 96 % of Fe, 75 % of Zn and 92 % of Cu could be removed from the acid mine water with an attendant increase in the pH value by two units. The free energy of adsorption of the metal ions onto rice husk and tree bark is found to be negative in both the cases, while the adsorption process is endothermic in the case of rice husk and exothermic for tree bark. The adsorption process is found to adhere to the Lagergren pseudo-first order rate equation. The reduction of sulphate con-centration in the acid mine water is achieved using a typical sulphate reducing bacteria namely De-sulfotomaculum nigrificans. Desorption experiments indicate that about 88 % of Zn, 87% of Cu and over 77 % of Fe could be recovered from rice husk and over 70 % of Fe, 82 % of Zn and 77 % of Cu could be desorbed from the metal loaded tree bark using 5 M HCl. The possible mechanisms of metal ion and sulphate removal from acid mine water using rice husk and tree bark are discussed.

Jan 1, 2014

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By J. Z. Yuan

The purity of rectorite is only about 70% after preliminary mineral processing, which has limited its application. In this research, different pulp densities, different dispersants, different dispersing methods and purification flow sheets were used to purify rectorite. The results show that it is possible to obtain high pure rectorite clay with the purity above 90% and concentrate yield between 24.9% and 29.4% by the purification process with composite dispersants, stirred mill grinding dispersion and so on. The obtained high pure rectorite can be further used in rectorite nanocomposites.

Jan 1, 2014