Search Documents

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has' been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

By Brian T. Brady

The year 1991 recorded unprecedented change throughout the world; war in the Middle East, economic recession in key industrial nations, upheaval in Eastern Europe, and the disintegration of the former U.S.S.R. These issues and growing environmental concerns will affect the entire world mining industry. Environmental issues continue to have an ever greater effect on industrial minerals. In the United States, major issues involving the Clean Air Act, Clean Water Act, and the recent Stormwater Rule by the U.S. Environmental Protection Agency (EPA) affect many types of mineral operations. Significant developments include an important decision in 1991 by a Federal Appellate Court to overturn EPA's asbestos ban on certain products, partly on environmental grounds, and proposed legislation that would overhaul or abandon the 1872 Mining Act. On a global scale, prominent issues include environmental concerns over mining in the Antarctic and Arctic regions and a cutback in plans to clean up the Kola Peninsula in the Commonwealth of Independent States (C.I.S.).

Jan 1, 1993

By G. E. McElroy

The purpose of tins paper is not to present new date on the pressure losses due to bends and chances of area in mine openings through which air flows, but rather to correlate existing data, determined mainly on small duct systems and expressed in a variety of ways, according to uniform methods that facilitate their use in pressure-loss computations. These are required in such, air-flow problems as determining the quantity that will flow through is mine openings under a certain pressure difference or, conversely, the pressure difference that will be required to maintain a certain rate of flow. Air flowing through h ducts, such as mine airways, encounters resistance to flow due to interference of the individual air streams with each other caused by the wall surfaces. The result is that part of the kinetic energy of the flowing stream is converted to heat; and constant renewal of the kinetic energy from the total energy of the flow is required to maintain it. This process manifests itself by a decrease of the total pressure (static pressure plus velocity pressure; of the air in the direction of flow; in order that flow pray occur, there must necessarily be a differences in total pressure between the two cads of the air-ay equivalent to the pressure losses occasioned by the flow, which automatically adjusts itself in magnitude to the pressure difference maintained.

Jan 1, 1932

By D. S. F. Silva

A survey of 120 recent NI 43-101 technical reports was conducted to evaluate the current state of practice regarding resource classification techniques. The most common classification techniques are based on search neighbourhoods (50% of recent reports), drill-hole spacing (30% of recent reports), and/or kriging variance (6% of recent reports). Two new techniques are proposed. The first is based on kriging variance and involves removing one or more drill-holes with the highest weights while performing kriging and using the resultant kriging variance for classification. This technique has the advantages of variance-based techniques and reduces artifacts. The second technique is based on conditional simulation and uses a moving window approach for classification at the desired selective mining unit resolution based on larger production volume criteria. This technique has the advantage of accounting for heteroscedasticity, which is a common characteristic in mineral deposits, and also reduces artifacts since a production volume scale is considered for the actual classification. The drill-hole spacing, search neighborhood, kriging variance, and simulation-based techniques are described and compared for 2D and 3D examples with regular and irregular drilling patterns to highlight the advantages and disadvantages of each method.

Jan 1, 2014

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003

By Francis T. Freeland

In the West many precious-metal mines are worked in patches by lessees, under conditions which closely resemble those of what is called " tribute-work" in Cornwall.* The company has its own foreman or inspector, and usually employs the engineman, blacksmith, pumpman, and perhaps other general workmen. As an inducement to work on a new piece of ground, where no ore is in sight, the company may advance a " footage"

Jan 1, 1896

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By P. C. Schutte

There have been several high-profile accidents in the South African mining industry where fatigue was identified as either causal or contributory. The risk of fatigue is inherent in any work-time arrangement involving shift work and work that is physically or mentally demanding, repetitive, or requires high vigilance. The management of fatigue is not simply a matter of correct shift scheduling. Amore comprehensive approach is needed. In order to be successful, a fatigue management programme should address the unique needs of the operation in which it will be implemented and should be integrated into normal operations. Fatigue management is a shared responsibility between the organization and its employees, and all stakeholders should participate in order to provide the safest and healthiest working environment possible.

Jan 1, 2010

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013