Search Documents

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By M. A. Stoakes, H. D. S. Miller

Surface subsidence is becoming an increasingly important factor in the economics of mining Louisiana salt domes due to, amongst others, excessive shaft deformations and land loss to encroaching sea water. The vast majority of subsidence studies have been undertaken on bedded, tabular deposits. It is important to understand the causes of subsidence due to mining domal salt and how it can be minimized. The paper will review the major differences between subsidence caused by domal and tabular evaporite mines, the problems encountered in predicting subsidence, the factors that influence subsidence and, finally, possible alternative mining methods.

Jan 1, 1986

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at 'any of several stages of extraction and processing, the stage of measurement used In this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the product of auxiliary processing at or near the mines.

Jan 1, 1977

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By Steven W. Schmauch

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines Studied 25,340 acres of the 28,960-acre Twelve Mile Creek Wilderness Study Area (OR-003-162) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 30 miles northwest of McDermitt, NV. The area is underlain by thick sequences of rhyolite to with lesser amounts of andesite and basalt flows. Bureau of Mines personnel reviewed pertinent literature, mining records, and examined the study area for possible mineral resources in geologically favorable sites. There are no organized mining districts and no record of past or current mining activity. Based on sample results, published literature and field observations, there are no identified mineral resources.

Jan 1, 1987

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Sidney Katell

The present report, a continuation of the series of Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, is concerned with articles published from January 1958 through December 1958. The periods covered in previous reports are as follows: January 1930 - August 1948 I. C. 7516 September 1948 - June 1952 I. C. 7705 July 1952 - June 1954 1. C. 7751 July 1954 - December 1956 I. C. 7847 January 1957 - December 1957 I. C. The following sources were used to obtain the references to and the abstracts of the published articles included in this report: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Coal Age. 6. Coal Utilization. 7. Cost Engineering. 8. Industrial and Engineering Chemistry. 9. Nucleonics. 10. Oil and Gas Journal. 11. Petroleum Engineering. 12. Petroleum Refiner. 13. World Oil.

Jan 1, 1959

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

By Daniel Hack

A few progressive mining software companies have recognized the benefit of broadening their capabilities to the sand and gravel (aggregate) industry. The most promising new developments have been designed for use with Surpac Vision, one of the world’s leading geological modeling, mine design, and production management systems. Surpac’s broad user-base, who have always had a propensity for customization, are now focusing on development of solutions in the Tool Command Language (Tcl), an interpreted scripting language. Surpac Software International made changes to TCL to add Surpac specific extensions, thus creating the Surpac Command Language (Scl). The Tcl interpreter, including Scl extensions, is bound into the Vision executable to provide a seamless interface to the data objects used internally by Vision, the GUI, and the 3D rendering system. Custom solutions can be incorporated as Vision extensions, or as stand alone-modules used in correlation with modeling, design, and planning functions.

Aug 25, 2002

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By William H. Schiffbauer

The Bureau of Mines is conducting research that is aimed at making the mining industry more efficient in term of both productivity and the health and safety of the worker. As part of this research the Bureau of Mines has integrated a testbed composed of computer and related peripheral hardware to form an intelligent base for performing autonomous mining machine experiments. Although this particular application was con- figured for use on a Joy 16 CM mining machine, its generic structure facilitates its attachment to a variety of mining machine types. The multitasking multiuser computer can be set up for other applications by changing a bubble memory cartridge. The Joy 16 CM implementation includes 96 digital input-output (1-0) ports, 32 analog inputs, 8 analog outputs, 2 serial data channels, and 1 printer port. Operation of the machine can be performed either through a local terminal or remotely through a modem hookup. This report describes a testbed for autonomous mining machine experiments (TAMME)--its hardware, software, and complete system integration--so that it can be used as a foundation for other applications.

Jan 1, 1988

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Hennessy F. L

It is generally recognised that slags are active participants in pyrometallurgical processes, and not merely inert liquids which must be produced. to effect separation of gangue material in smelting, or of impurities in refining. The importance attached to slag-metal reactions in steelmaking is shown by the numerous investigations in this field. However, there are still many important reactions of slags which require explanation. In this paper some new aspects of the reactions of slags will be discussed, as far as possible quantitatively.FREE AND COMBINED OXIDESMetallurgical experience indicates that variations in the composition of slags produce changes in the chemical behaviour of the various components. These variations have been generally ascribed to changes in the proportions of free and combined oxides, i.e., compounds have been assumed to be present in the liquid slag.Considerable support for this view has been adduced from the existence of compounds such as metallic silicates, phosphates, etc., in the solIdified slag. However, this does not imply that such compounds necessarily exist in the molten slag.The most direct evidence as to the nature of molten slag is to be obtained from a study of the liquid state. In...

Jan 1, 1950