Search Documents

By L Spencer, H Zwingmann, I Graham, D Cendon, B Kelly, D Burkett, F Lau, P Lennox

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kulumadau deposit represents an intermediate-sulfidation epithermal gold deposit (3.8 Mt at 2.3 g/t, Ag:Au = 1). Mineralisation is primarily confined to hydrothermal breccias within pre-existing fault zones, where it is disseminated throughout a hydrothermal matrix comprising chlorite-quartz-adularia-illite-I/S clays-calcite-pyrite. The host sequence represents numerous mid-Miocene pyroclastic flow eruptions within a tectonically active emergent shallow marine to subaerial depositional setting. Subsequent growth faulting was responsible for debris avalanches, which were subsequently cut by reverse faults. Faults were exploited by hydrothermal fluids, with the heightened porosity at the juncture between faults and debris material facilitating boiling of the ore constituents. Fluid inclusion studies suggest that fluid mixing between meteoric fluids and magmatic fluids, accompanied by boiling, were the primary mechanisms for gold deposition. The occurrence of anhydrite/gypsum as late-stage veins and their sulfur and oxygen isotopic values indicate post-mineralisation mixing of sea water with hydrothermal fluids.CITATION:Burkett, D, Graham, I, Spencer, L, Lennox, P, Cohen, D, Zwingmann, H, Lau, F, Kelly, B and Cendon, D, 2015. The Kulumadau epithermal breccia-hosted gold deposit, Woodlark Island, Papua New Guinea, in Proceedings PACRIM 2015 Congress, pp 205–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Fabian Kirsch

Cyclic behaviour of axially loaded piles has been an issue since studies revealed that the capability to transfer skin friction into the ground is highly depending on the level and the number of load cycles the pile is subjected. It has been shown that degradation of skin friction due to axial cyclic loading leads to accumulating displacements and a severe reduction in pile capacity. In Germany the DIN 1054 as well as the Recommendations of the Working Group 2.1 ?Piles? of the German Geotechnical Society (EA-Pfähle) require the consideration of cyclic loading for the assessment of both the displacements and the capacity. Up to now no broadly accepted design method exists, which enables the engineer to give a reliable judgement on the pile capacity under axial cyclic loading and the displacements respectively. Instead numerous design charts make it possible to distinguish between stable and instable loading levels in order to ensure a design on the safe side. A newly developed design approach based on engineering models is presented which delivers a calculation algorithm for the remaining axial pile capacity after a defined number of load cycles to allow for the analysis of stability of the foundation. Furthermore the computation of accumulating displacements is made possible. The results are verified with pile load tests undertaken at Dunkirk, France and showed that the axial capacity after cyclic loading calculated with the newly developed design approach predicts actual capacity with an accuracy of ±20%.

Jan 1, 2011

By Mario Terceros H, Bengt H. Fellenius

"ABSTRACTThe city of Santa Cruz, Bolivia, is historically dominated by houses and three to five storey buildings.The geology in and around the city is such that even very light buildings need to be supported onpiles. The recent increase of the Bolivian economy, notably that of Santa Cruz, has created a demandfor new residential as well as office and industrial buildings, which mostly consist of multi-storey orhigh-rise buildings with significantly larger foundation loads. Foundation piles have become largerand longer, and the load on individual piles is increased. The development has resulted in an increasein the demand for more sophisticated design and construction methods and stricter approach toverifying the quality of the construction processes and results.This paper describes to geology of the Santa Cruz region and how the geotechnical conditions areconsidered in the design and construction of piled foundations. The improvement of past constructionand design techniques, based mostly on bored piles constructed with bentonite slurry, is beingreplaced with new methods of constructing bored piles, e.g. the Full Displacement Pile (FDP) andincorporation of techniques such as enlarging the pile toe, e.g., with the Expander Body. This paperpresents the results of several full-scale tests and discusses the incorporation of the test results indesign and construction.1 GEOLOGY OF THE REGIONSanta Cruz de la Sierra is located in the eastern lowlands and sub-Andean zone of Bolivia, SouthAmerica. The area lies at an elevation of about +400 m and the geology is a Paleozoic (250 millionyears old) sedimentary basin. The soils of interest to civil engineering construction are quaternarywith the dominant minerals being calcite, silica and feldspar. The main agent is the Piray River and itstributaries. Their past meandering over the area has resulted in a sedimentation-erosionsedimentationprocess and a profile dominated by fine to medium sands with intermittent layers ofclay or clayey sand. With increasing distance from the river, the clay-containing layers are thicker.Fig.1.- View of Bolivia with location of Santa Cruz and map of Santa CruzThe upper about 15 to 18 m thick part of the profile consists of normally consolidated layers of clays,silts, sands, in various combination and thickness. Below, the soil is more homogeneous and consistsmostly of sand and gravel. The groundwater table lies typically at a depth of about 6 m in the highestpart of the city and at about 1 to 3 m depth in the lowest part of the city."

Jan 1, 2014

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

As metal prices fluctuated over the years, so too have the fortunes of many of those mining in Canada?s Yukon province. With a rich mining history that dates back to the Klondike gold rush of 1896 to 1898 and continues to thrive today, Yukon has experienced several ?boom-and-bust? cycles. However, during the world?s most recent mining ?bust? Yukon has held strong and has re-mained one of the world?s hottest destinations for mineral exploration. In fact, the area even exceeded forecasts in 2009, more than doubling last year. And the near-future looks just as bright.

Jan 1, 2010

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By Joseph Blake Smith

Coal resource data from published sources and company files were used by the Bureau of Mines to determine the location and extent of strippable coal reserves in Wyoming. Total strippable reserves of 23 billion tons were estimated in seven major coal areas. Seven large strip mining operations were active in 1969, and their production totaled 45 million tons of coal. Cutoffs used to define strippable reserves were (1) minimum coalbed thicknesses of 5 feet; (2) overburden-to-coal ratios of less than 10 cubic yards of over- burden per ton of coal; and (3) total overburden thicknesses of less than 120 feet, except where reserves occur in multiple beds or a single thick bed. Tertiary rocks along margins of the Powder River basin contain most of the strippable coal reserves in Wyoming. The Wyodak beds, ranging in combined thickness from 30 to 1.30 feet, crop out on the east flank of the basin and contain an estimated 19 billion tons of strippable subbituminous C-rank coals under less than 200 feet of overburden. Partings between these beds total less than 60 feet. The 100- to 200-foot-thick. Healy bed on the western flank of the basin and the 35-foot-thick School and 20-foot-thick Badger beds on the south also contain large strippable reserves. Elsewhere in Wyoming, strippable reserves. Elsewhere in Wyoming, strippable deposits are subbituminous coal of Late Cretaceous and Tertiary ages, mostly in the Hanna and Great Divide basins in the south-central portion of the State and in the Kemmerer-Hamms Fork region in the southwestern corner.

Jan 1, 1972

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"For about 20 years, the use of bacteria to control the flotation process for the production of raw material concentrates has been the subject of worldwide scientific and engineering efforts. The objective is to reduce the consumption of biologically non-degradable toxic reagents. The principle idea is to use the activity of bacteria in natural leaching processes – known since the middle of the last century – for controlling flotation processes.It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS), excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 21 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction. Pure mineral phases and mineral mixtures were used for the flotation tests. The outcome was reproducible results with technical flotation machines. The research results known so far are mainly based on investigations with micro flotation devices, which are usually used for the characterization of reagents and which do not allow a direct translation to the technical scale."

Jan 1, 2003

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009

By John Smyth

Mining through in panel entries and the full face recovery method has been successfully practiced at U.S. Stwl, Mine 50. Suppat of the cut-through entries and recovery room is critical. Traditionally, concrete crib or fly ash cement backfill has been utilized. However, these traditional methods are not feasible at Mine 50 due to the difficulties of the plow face mining through these types of support. Recent development of new cable support systems provides an option for cut-through entry support. Mine 50 and Jennmar Corporation personnel have worked together to design and apply the cable systems in the cut-through entries and full face recovery room to eliminate standing support. To date, a number of full face recovery rooms and cut-through inpanel entries have been successfully mined. The results indicate that the cable systems combined with high capacity shields, have provided sufficient capacity to support the roof. Utilizing the Jennmar Finite Element Analysis (JFEA) computer program (Stankus and Guo, 1996), an analysis of the stress and roof deflection changes as the longwall gradually cut through was conducted. From the finite element analysis data, a supplemental support plan was designed. The history and experiences at Mine 50 are presented. Based on the case experiences and modifications made to the finite element analysis, an improved design criteria for future use has been formulated.

Jan 1, 1998

By Juliana Colacioppo

La voladura es un procedimiento que está diseñado para obtener pilas a través de una fragmentación adecuada para el carguío y transporte, aumentando así la productividad de las palas y camiones y asegurando la estabilidad de los taludes y condiciones del piso de los bancos en la mina. Asimismo, el diseño de la voladura debe optimizar las operaciones posteriores tales como chancado, zarandas, clasificación, molienda, flotación y lixiviación. En ese sentido, el presente texto describe la metodología de optimización de procesos de la miina Antamina hasta la oncentradora a través de la recolección de datos de campo, caracterización, modelación matemática y simulación de las operaciones, donde además se utilizan sistemas de rastreamento de minerales y de análisis continuo de imágenes.

Sep 9, 2007

The 1999 edition of the Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves (the æJORC CodeÆ) became effective in September 1999 and is the latest revision of a Code which was originally issued in 1989, but which has an ancestry dating back to the first JORC report released in 1972. The modifications introduced in 1999, which are briefly discussed in this paper, substantially improved the document, but did not materially alter the fundamentals of the Code, these being the Mineral Resource/Ore Reserve classification framework and terminology, and the requirements and guidelines for public reporting of Resources and Reserves. Codes or guides similar to the JORC Code exist or are under development in other countries, including the United States of America, Canada, the United Kingdom and South Africa. It is pleasing to note that the 1999 JORC Code has been used as a model by these countries in developing their latest standards, and has been a major influence in the formulating of international reporting standards. The JORC Code is primarily a document covering the reporting of the results of mining companiesÆ activities to the public. However, mining geologists are interested in practical assistance and guidance in carrying out their duties. The JORC Code provides this in four ways. It establishes a framework within which those preparing and publicly reporting Mineral Resource and Ore Reserve estimates must operate, by setting standards for the classification and reporting of Resources and Reserves and for qualifications of Competent Persons. It establishes the division of responsibility between the companyÆs Board of Directors and Competent Persons with respect to the preparation and reporting of Resources and Reserves, and empowers Competent Persons to materially influence how their Resource/Reserve estimates are reported to the public. It provides an extensive, detailed and practical check list of criteria to be taken into account in the preparation of Mineral Resource and Ore Reserve estimates. Finally, it provides a strong measure of due diligence protection in the event of litigation if it is followed with diligence and honesty.

Jan 1, 2000

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man's house as it was mined. Then it may have been stockpiled at each man's place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By P Moswate, D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of gangue mineral grade limits by the concentrator may also result in significant penalties.Online grade analysers which can provide reliable real time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and has the benefit of operating in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades.MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at the BCL nickel concentrator plant in Botswana. The project focused on stabilising the final concentrate grade while ensuring the final tailings are minimised, resulting in an improved nickel recovery. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser. The positive results show the advantages of combining reliable real time measurements with an advanced process control system.CITATION:Mantsho, S M, Moswate, P, Strobos, P and Phillpotts, D, 2013. The implementation of floatstar grade-recovery optimisation control solutions using Blue Cube Online grade analysers on industrial flotation circuits, in Proceedings MetPlant 2013 , pp 575-582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By William H. Dresher

Introduction A subject long debated but rarely resolved involves the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is, unfortunately, too often treated as a controversy involving ethics and the profit motive. But, in fact, the two branches of society - industry and academia - are necessarily part of the same system. In the last 25 years, the realization has developed that research alone is not sufficient to bring about use of those results to benefit society through productivity gains and economic growth. The flow of events shown in Fig. 1 was generally believed to be the steps required for reaping the benefits of research. Today, research still has the very important role of creating new information or new ideas. However, it is recognized to be but one of many steps in a process that we now refer to as technological innovation. Charpie (1967) said, "Technological innovation is the driving force behind economic growth in the US. In this context, innovation means the process by which a new idea is successfully translated into economic impact within our own society, by providing better products, and simultaneously creating new jobs in the manufacturing of those products. Only after an investigation is put into sufficient use to have an economic effect, is it termed an innovation." One of the best depictions of the technological innovation process is shown in Figs. 2 and 3. These are adapted from Haeffner (1975), and modified by the Committee on Mineral Technology of the National Research Council (1981). Figure 2 identifies the many steps involved in the process. It designates a generalized form for interaction between the academic community and industry. Figure 3 identifies the steps in the "innovation activity" box of Fig. 2. Academia is generally responsible for developing of new knowledge and ideas, as well as maintaining and enlarging the collected body of scientific knowledge. Industry is responsible for developing new products, methods, and processes. Both institutions operate for the benefit of society, but under different driving forces. In academia, the driving force is the achievement of academic excellence. In industry, the driving

Jan 10, 1984