Search Documents

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By Kenneth H. Johnston

Records show that waterflooding was tried in Osage County as early as 1934, but it was not economically important until a large unitized flood in the North Burbank field was begun in 1950. Development was rapid and by the end of 1960, there were 70 active water flood projects and 16 active pressure-maintenance projects in the County. The locations and status of the water-flood and pressure-maintenance projects in Osage County on December 31, 1960 are shown in figure 1, and information pertaining to these projects as of July 1, 1960 is given in table 1. For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meeting of the Kansas-Oklahoma Water flood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1961 spring tour of three waterflooding projects and a pressure-maintenance project in Osage County, Okla. (fig. 2).

Jan 1, 1961

Illumination hardware developed in conjunction with previous Contracts H024202l, H0242049, and H0242023 had not been adequately tested in actual underground work situations. The purpose of this contract was to install and monitor this equipment on mining machines and in actual working places of coal mines to gain experience with the use of the lamps and support equipment in the abusive and critical environments for which they were intended. The equipment that was to be tested consisted of the following: a. Lamps -A variety of sizes of permissible fluorescent lamps which operate from 12 volts DC power. These include the following sizes: Model 8, (9 watts) 2" diameter; Model 15/2 (14 watts) 2" diameter; Model 15/3 (21 watts) 3" diameter; Model 20 (25 watts) 3" diameter; Model 30, (28 watts) 3" diameter; and Model 40, (39 watts) 311 diameter. Representative photographs of these lamps are shown in Figure 1-1 and 1-2.

Jan 1, 1976

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7,200 kg (15,900 lbs) per day or 61%. Metals loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change, and fewer than 1% got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2002

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

Cessation of mining on the Bendigo goldfield makes it evident that, as the older generation fades away, knowledge of the famous Bendigo saddle reefs will be limited in the future by their written records. It is important therefore that the summarised account by D. E. Thomas (1953) in the Geology of Australian Ore Deposits should not be misleading. Fig. 6 in this article is stated to portray a cross section and longitudinal section through a series of gold shoots in the Garden Gully 300 ft. reef. The gold shoot along the capof the saddle reef is represented as extending down the east leg in a series of prongs, with the tips of the prongs about 50 ft. apart. It is the purpose of this note to indicate that this illustration can be suspected to be a diagram of the old stopes instead of a diagram of the distribution of gold in the quartz.The original sketches of Figs. 6 and 7 in Thomas' account were extracted, I believe, from the field note books of H. S. Whitelaw, years after his death in the late twenties. Whitelaw was stationed in the Bendigo office of the Geological Survey of Victoria, carrying out geological surveys of the Bendigo mines. He was there for many years before the Gold Research committee started its investigations in 1916 and he was acutely aware of the problem attached to the distribution of gold in the reefs. He had felt concern that manyauriferous reefs were being mined without adequate study and record and he decided, as he expressed it to me, to pick up what he could as he went along. There can be little doubt that the diagrams of Figs. 6 and 7 are products of this resolve.Opportunities to investigate gold occurrences at Bendigo were limited before 1916 because the field was operated by Manuscript received at The Institute 18th November, 1960.

Jan 1, 1961

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002

The 2003 SME Annual Meeting and Exhibit will take place Feb. 24-26 in Cincinnati, OH. The meeting will feature a host of special symposia and programming geared toward the industrial minerals and aggregate industry sectors. This programming focus is particularly relevant for this annual meeting, as it will be hosted in the center of America’s transportation hub and industrial mineral center. Cincinnati, located on the Ohio River, is key to the movement of America’s supplies and construction material needs.

Jan 1, 2003

If the industry keeps doing what it has always done, it will continue to get what it has always got - rising operating costs. Why is this so? Generally grades being chased are becoming lower, stripping ratios becoming higher, ability to attract personnel to the industry becoming harder and/or more expensive, higher safety standards are being demanded and environmental governance is being enforced.   How then should the surface mining industry plan for the future whilst delivering on improved safety and the environment? In-pit crushing and conveying (IPCC) points the way, as a partial or complete substitute for trucks.   IPCC systems promise significant advantages over traditional truck and shovel operations, including improved safety, reduced operating costs, reduced dust and noise emissions, far greater efficiency in energy use (electric versus diesel motors predominantly and the ability to regenerate electricity back into the local grid for downhill situations), reduced carbon emissions (dependent on power generation source) and reduced water consumption. Despite these advantages, there is a general industry reluctance to migrate from truck and shovel operations. This reluctance stems from a familiarity with truck and shovel operations and a perceived concern that IPCC lacks flexibility which will negatively impact on the mining operation.   In studies conducted since 2007 (with the new modular builds) comparing IPCC with truck-optimised pit designs, IPCC has delivered up to USD$0.82 per tonne moved less than an equivalent truck operation. In addition, IPCC is easily automated from a central control room (local or remote) - something that trucks have yet to commercially achieve.   IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations - its safety, the impact on the environment and its costs. It maybe of interest to note that there is over 200 IPCC installations worldwide today.   This paper and presentation will assist in furthering the understanding of IPCC and its applicability.

Jun 1, 2010

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By W G. Szymczak, Leslie C. Taylor

The University of Maryland (UMD) has conducted a series of small-scale tests using explosive charges buried in saturated sand. Twelve different combinations of depth of burial of the charge and height of the target plate above the soil were tested. The target plates did not deform plastically. High-speed video was used to track the motion of the plate. The video data are analyzed to determine the position and velocity of the plate as a function of time. The results of this analysis are compared with computations performed at NRL using the BUB2D computer code. This code treats the saturated sand as an incompressible visco-plastic fluid which yields according to a Drucker-Prager (frictional-cohesive) yield surface. Comparisons of simulations with experiments are presented. In the cases examined so far, the velocity grows very quickly to a peak and then slows, first with a deceleration greater than one “g,” which then transitions to an approximately one “g” deceleration. An analysis of air drag on the plates has shown that its effect is negligible in the time span of interest. In all cases in which the BUB2D code can be applied, the computations compare favorably with the results of the data analysis. This suggests that the code and model used in the computation are properly capturing the physics of the interaction between the soil and a non-deforming plate.

Jan 1, 2007

By J. Muller

Keywords: Pyrometallurgy, blast furnace, slag viscosity, slag liquidus temperature, phase equilibria The viscosity of molten slag in blast furnace operations is an important process variable, influencing the rate and location of reactions inside the furnace, as well as the ease with which the final slag could be removed from the furnace. To optimize these processes, it is necessary to estimate the slag viscosity and liquidus temperatures as accurately as possible, and know the target values. Models to predict viscosities and liquidus temperatures, incorporating phase equilibrium calculations, have been developed and validated with measured data. Various diagrams have been developed to illustrate how the properties vary with composition and temperature, including pseudo-ternary diagrams of SiO2-MgO-CaO-Al2O3 for viscosity and liquidus temperature. Models were also applied and methodologies developed to analyse historical blast furnace operations and determine target values.

Jan 1, 2011

By P J. White, J V. Lawless

Low-sulphidation epithermal gold deposits, which form in quasi-hydrostatic convective hydrothermal systems, frequently contain chalcedony within high-grade ore, which has been interpreted to be a crystallisation product of amorphous silica. To deposit amorphous silica rather than another silica polymorph at elevated temperatures requires very high silica concentrations, because of its relatively high solubility. Only extreme boiling caused by decompression followed by wall rock heating upon structural dilation, can achieve this. As gold deposits with amorphous silica it must be produced by the same mechanism, particularly since extreme boiling is also a very effective mechanism for gold deposition. Recent developments support this view; the first is the detailed isotopic analysis of chalcedony-bearing high-grade veins reported from Hishikari, Japan, in which oxygen isotope results are indicative of extreme boiling and hydrogen isotopes indicate initial deposition of amorphous silica. The second is the finding of chalcedony within geothermal pipe work in the Rotokawa geothermal field in New Zealand. Rotokawa is a comparatively hot field (335¦C at depth); hence separation of the steam-water mixture produced by the wells is undertaken at a comparatively high temperature (220¦C) to minimise down-stream silica scaling. Even so, silica scale, some of which is chalcedony, does occur, under similar conditions to that in low-sulphidation epithermal deposits. Evidence of chalcedony forming under these conditions, reinforces the interpretation that decompressive boiling is the main deposition mechanism for gold in low-sulphidation epithermal deposits. It is possible that there is sufficient drop in temperature due to decompression that, at least initially, the silica deposits directly as chalcedony. Low-sulphidation epithermal gold deposits that do not contain chalcedony, such as those in the Philippines, may form at temperatures too high for chalcedony to directly form. The recognition of decompressive boiling as the main deposition mechanism in low-sulphidation epithermal deposits means that exploration can focus on zones where this has taken place by combining paleohydrological reconstruction and structural geology.

Jan 1, 2002