Search Documents

By B Vernon, M Whiteley, T Robinson

The Western Australian gold industry has approximately 100 operating plahts, mainly CIP/CIL. The nature of the State's rapidly expanding gold industry gave rise to concerns over management of the  cyanide hazard, in that most plants are remote from major population centres, have a workforce with a high tum over and use highly saline process water. Approximately 4500 workers in the industry have the potential to be exposed to cyanide in the course of their normal work.   This paper outlines the risk management strategy developed by Government and industry to monitor atmospheric HCN gas in the work environment and the role of continuing education and training along with regular site inspections by Department of Mines Inspectors.

Jan 1, 1990

By S. E. Burton

The White Rock area of the Boiling Springs manganese-iron deposits comprises about 3,200 acres of land in Monroe Township, Cumberland County, Pa. (See fig. 1.) This property was brought to the: attention of the Bureau of Mines by Pennsylvania Geological Survey Bulletin 128, entitled "Manganese Ores of Pennsylvania" by R. M. Foose. It was examined by an engineer of the Bureau of Mines in August 1942 and was further investigated by the Bureau by churn drilling and underground development during the period December 1942 to February 1944. Beneficiation tests were made on samples of the ore. This report describes the work done during the investigation and presents the results obtained.

Jan 1, 1949

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By Christopher P. O?Connor

Stereolithography is a well known rapid prototyping technique in the manufacturing sector. Essentially it is a three dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of Rapid Prototyping Techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models and in cases where it is decided to develop physical models, the process is time consuming based on simplified constructions. Rapid prototyping techniques (RPTs) such as stereolithography can facilitate engineers and geologists to quickly and with satisfactory accuracy to visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with the Department of Mines Research of Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs (e.g. stereolithography) to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems.

May 1, 2002

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on any type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the ground outside seemed to shake the building as a single, loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an&apos; type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By Merle L. Bowser

An alinement (steering) sensor for continuous mining machines has been developed under a Bureau of Mines contract. A laser source in the entry projects a beam parallel to the centerline of the entry. The beam is optically shaped to a narrow, vertical fan and illuminates an array of optical sensors bunted on the mini machine. These sensors interpret the location of the beam into meter readings of heading (angle) error and lateral displacement errors. The system, which was tested for 5 months in an operating mine, appears to be fundamentally sound, and with some modification, should be applicable to remote or automatic guidance of continuous miners and other machines.

Jan 1, 1976

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand&apos;s largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

Mineralisation was identified at Gladstone Hill as far back as the late 1870&apos;s û early 1880&apos;s, shortly after the initial discovery of Martha Hill. Indeed, early recovery problems from the Martha Hill mineralisation led to the preferred development of are bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, Union to name a few. Work at Gladstone Hill is carried under the Union Hill Joint Venture, a 50:50 joint venture between Auag Resources Ltd - manager (a fully owned subsidiary of Otter Gold Mines Ltd) and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Hill operation. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Hill, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with the Gladstone vein set and the more recently identified high grade Moonlight Lode. Veining ranges in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. The potential for the Gladstone Hill area is yet to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 1999

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004