Search Documents

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

The Clyde Power Project, and its Clutha Valley Development forerunner, has taken widespread investigations for various hydroelectric purposes both along the valley floors upstream from Alexandra and on the higher schist terrain. As part of this work the nature and extent of many of the alluvial deposits have been resolved and the ages established with varying precision. Gold values have been approximately appraised in some areas as an element of environmental assessment.

Jan 1, 1992

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Greisson Peixoto Rangel

A variação da resistência à compressão de argamassas geopoliméricas foi estudada em função da razão ativador/precursor e da molaridade da solução ativadora. As argamassas estudadas foram confeccionadas com metacaulim (precursor) ativado com solução composta por hidróxido de potássio e água destilada, e areia normal brasileira. De acordo com os resultados, a resistência aumenta com a diminuição da razão ativador/precursor e com o aumento da molaridade da solução ativadora. Além disso, os valores encontrados condizem com os presentes da literatura e com possíveis aplicações para argamassas de múltiplo uso.

Oct 30, 2017

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

By David K. Ingram

The Bureau of Mines conducted underground mapping and rock strength tests to describe and analyze mine roof conditions surrounding ancient stream channel deposits (paleochannels) in the Pittsburgh Coalbed in southwestern Pennsylvania. Paleochannels in the study mine consist of sandstone and/or siltstone and affect the Pittsburgh Coalbed through erosion and/or differential compaction. Differentially compacted sediments within and adjacent to channel deposits caused slip planes, faults, clay-dike faults, clastic dikes (clay veins), coalbed rolls, and slumped structures. Paleochannels can be predicted by recognizing these features and associated sediments, which allows for modification of long-and short-term mine planning and development. Mine entries located beneath the paleochannel deposits exhibit less stable roof conditions than entries with normal (nonchannel) roof. Paleochannel deposits comprise only one-fourth of the mapped study area; however, they contain one-half of the hazardous roof. This study deter-mined that rock strength evaluations, including rock quality designation (RQD), unconfined uniaxial compressive strength testing, and point-load testing, must be accompanied by underground observations. Suggested remedial support techniques include angled and/or longer tensioned bolts, steel mats or crossbars, steel sets or cribbing, and roof trusses.

Jan 1, 1987

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell's Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.' The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

Investigation on Multicomponent Semi-Autogenous Grinding

Sep 13, 2010

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By J. P. Capp

The Bureau of Mines conducted field-scale experiments in underground gasification of coal with oxygen-enriched air. A path about 140 feet long was linked at the rate of LO feet per day through a coalbed hydraulically fractured with a mixture of starch gel and sand. During the best gasification period, which extended for 2-1/2 days, 785,000 std. c.f. per day of 124-B.t.u. gas was produced. In other periods the heating value at times was almost 300 B.t.u. per std, c.f,, but sustained production of such gas was not achieved. During gasification, a total of 50 tons of coal was gasified and 114 tons of coal was carbonized. Approximately 12 million B, t .u. per foot of nominal path was recovered at the surface.

Jan 1, 1962

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By William F. Hahn

This report describes an illumination system suitable for use in a slope under construction, Simulator work was performed using actual lighting hardware to verify adequate light levels to meet MSHA proposed regulation (as published in the Federal Register, January 13, 1977). The sequence of operating activities for two different slope driving sites are discussed and lighting requirements are defined for each,

Jan 1, 1981