Search Documents

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By Raja V. Ramani

Discussion in this section of the Handbook is limited to the working environment of miners, the mine workers themselves, and the machines used in mining (Fig. 11.0.1). The contents emphasize personnel health and safety aspects and engineering design and control practices to ensure a productive health and safety environment. Reference is to the health and safety of the individual miners as well as to the safety of the working environment. This Handbook also contains references to health and safety regulations in Chapter 3.2 and environmental protection in Chapters 3.4 and 7.3.

Jan 1, 2008

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By John E. Conley

The need for lightweight aggregate for use in concrete products ,and structures has caused the Bureau of Mines to undertake an investigation to determine the availability of suitable raw materials and to study methods, procedures, and equipment to supply that need. Evidence is at hand to prove that the shortage of lightweight aggregate is nationwide. A survey recently covered in a report (13)5/ by the Construction Branch of the National Housing Agency has pointed out the locations in which lightweight aggregates are produced. A study of this information discloses that the producing centers are widespread, and that certain areas, notably the region east of the Mississippi River, and especially the sections along the Atlantic coast line and the Southeastern States, have only a few such plants. Certainly, many localities are badly in need of installations equipped to provide an ample supply of high-grade lightweight aggregate. The work undertaken by the Bureau of Mines includes investigation of the use of clays, shales, slate wastes, coal-mine wastes, diatomite-clay combinations, and various other 'mineral mixtures as possible raw materials. Likewise, special consideration has been given to the development' of equipment and techniques to produce the lightweight products.

Jan 1, 1949

By H. H. Heady

This Bureau of Mines report provides specific information regarding the analysis of ores, concentrates, and bullion. It describes analytical services provided by some Federal agencies, and discusses analytical techniques applicable to the precious metals. The appendixes list Bureau of Mines State Liaison Offices and commercial assay laboratories.

Jan 1, 1976

Casing or lining pipe is used in boreholes for the following reasons:1. To preserve the hole while drilling and after it is finished.2. To shut water out of the hole or to isolate any particular water, gas, or oil-bearing stratum.Deep holes can seldom be drilled without casing, and only when in firm strata. If caving from the walls is at all likely while drilling, casing is necessary in order to prevent the tools horn being buried...

Jan 1, 1924

By J M. Totterdell

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid-Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian-Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

By D. S. Yantek, C. B. Brown

The mining industry is beginning to implement lithiumion batteries (LIBs) to power mine utility vehicles (MUVs) and rubber-tired mantrips (RTMs). However, the ability of LIBs to withstand the harsh conditions for these applications has not been rigorously evaluated. Concerns with the use of LIBs in the mining environment will be discussed including the effects of mechanical shock and vibration, temperature extremes, and moisture exposure. This paper will discuss adverse effects of the mining environment on LIBs and provide an overview of scientific gaps associated with the environmental susceptibility of LIBs used on MUVs and RTMs.

Feb 1, 2024

By C. M. McCulloch

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°. This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

This report presents the results of a study for the Bureau of Mines to compare loan terms for non-fuel mineral projects in developing countries, from various International Financial Institutions (IFIs), and from private sector commercial sources. The study compares IFI and commercial loan terms for seven mineral projects in developing countries. The International Financial Institutions represented are: ? International Bank for Reconstruction and Development (World Bank) ? International Finance Corporation (IFC) ? Inter-American Development Bank (IDB) ? Asian Development Bank (ADB) ? International Monetary Fund (IMF) In addition, the costs of financing for these mineral projects were compared with the costs of long-term debt to the five largest U.S. mineral producers.

Jan 1, 1986

By Charles F. Jackson

Gold mining is a subject that not only appeals to the popular imagination but has vital importance to the world's economic structure. However, a discussion of the use of gold as a medium of exchange, and a basis for credit between nations and for monetary systems is not within the scope of this paper. The importance of gold in carrying on the commerce of the world, the present supply and rate of production, the probable trend of future production, the probable future requirements, and related subjects have recently received much attention from bankers and economists, and many articles on these subjects have been published. During slack periods of base-metal production due to falling prices, accompanied by scaling down of base-metal mining operations and often by the closing down of at least some mines, there usually result revival of interest in gold mining, search for previously undiscovered deposits, and reopening of some old gold mines.

Jan 1, 1932

By Scott G. Britton

Mine exploitation is a broad subject whose focus is the technical skills or efforts needed for the extraction of mineral from a known ore body. Mine exploitation can be considered the very core of the mining engineering discipline. It begins at the conclusion of the exploration and development stages of mining and ends when the ore body is exhausted and the mine (or mines)closes and is reclaimed. Section 8 on mine exploitation is comprised of seven chapters: (1) classification of mining methods, (2) mine surveying and mapping, 3) systems engineering, (4) computer methods, (5) labor relations and training, (6) management and administration, and (7) mine closure, sealing, and abandonment. Each chapter focuses its efforts towards providing detailed and useful information for the engineer on basic mine exploitation principles. The information can be applied to a broad range of mining problems without regard to mineral type or mining method.

Jan 1, 2008

By Prosser A. P

The conditions under which vanadium is rendered insoluble by silica in the alkali-roast process have been investigated starting with both slag and reagent-grade materials. The inert phase is a glass formed slowlyfrom soluble NaV03 produced at lower temperatures. It contains approximately 30 per cent V in a partly reduced state; iron is not a principal component. Some of the vanadium in the inert phase is slowly returned to a soluble form by heating in an oxidizing atmosphere below the temperature at which the glass is formed (750°C). As the reaction leading to the required, soluble form of vanadium is also slow between 600 and 750° optimization and control of the temperature profile and atmosphere in the furnace, and the residence time of the solids, are necessary to ensure high vanadium extraction during subsequent leaching.

Jan 1, 1976

By A. Timur

Fluid flow properties of porous media have long been of interest in such varied disciplines as geology, geophysics, soil mechanics, and chemical, civil, and mechanical engineering. This interest has resulted in numerous models of porous media that have been proposed, tested, and found to be useful under, at best, only special circumstances. A critical review of most of these models is given by Scheidegger. 1 The application of each new tool to the study of porous media has helped to test some of the existing theories and to form new ideas based on the new parameters being measured. In the application of nuclear magnetic resonance (NMR) techniques to the study of the properties of fluids in porous media, the theoretical studies of Korringa et al.2 resulted in a model for the relaxation of spin polarization of protons in a hydrogenous fluid in a pore of a solid. Seevers3,4 verified this model, established a method for measuring the surface-to-volume-ratio distribution in a porous medium, and proposed a technique for determining specific permeability in sandstones. In the present investigation, the uses of NMR methods are extended and a simple model of porous media is developed from an analysis of pulsed NMR measurements. In this model, the pore spaces of a porous medium are divided into three groups on the basis of their surface-to-volume ratios. To evaluate predictions of the NMR model, laboratory measurements of spin-lattice relaxation time, porosity, permeability, and residual (irreducible) water saturation were conducted on more than 150 sandstone samples obtained from four oil fields in North America. Applications are discussed for estimating the volume of movable fluid, ?p, and the specific permeability, k, of sandstone samples. The former parameter, which can be considered as producible porosity, is expressed by ?p = [1 -- (Swr/100)]? , .... (1) where + is porosity in percent of bulk volume and Swr is the residual (irreducible) water saturation in percent of pore volume at a capillary pressure of 50 Psi. Fast, nondestructive laboratory methods are described for determining porosity, movable fluid, and permeability of sandstone samples from measurements with a pulsed NMR (spin-echo) apparatus. Procedures are given for adapting these methods to samples of irregular shape and small size. Theory General In the Korringa, Seevers, and Torrey2 (KST) model the observed decrease in the spin-lattice relaxation time, T1, of protons of a hydrogenous liquid contained in the pore spaces of a porous solid is attributed to an increase in the correlation time for the random motion of the water molecules and to the presence of paramagnetic centers at the liquid-solid interface. This KST model predicts the observed relaxation time of a hydrogenous liquid in a pore of a solid through

Jan 1, 1970

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By Staff

The goal of the U.S. Bureau of Mines diesel engine research program is to reduce exhaust emissions from diesel-powered equipment used in underground mines. This research has led to significant advances in aerosol measurement and to the development of more effective emission controls. This Information Circular contains reports of some of the presentations made at the Bureau's Information and Technology Transfer Seminar on Diesels in Underground Mines given in Minneapolis, MN, on September 29-30, 1992. The seminar emphasized the measurement and control of diesel particulate matter emissions. Topics covered include a discussion of the health issues associated with the use of diesel equipment underground, an overview of regulations, measurement techniques for diesel exhaust aerosol, levels of diesel exhaust pollutants found in mines, and modern emission controls. An appendix is included that contains a report describing the capabilities of the Bureau's diesel emissions research laboratory, two papers describing the effects of engine maintenance or: emissions, a paper describing the monitoring of carbon dioxide in mine air as an indicator of air quality, a glossary, and a list of abbreviations and acronyms.

Jan 1, 1992

A preliminary program dated April 25, 1974 was prepared for Development Engineering, Inc. (D.E.I.) on research and development, laboratory; field and other engineering studies for the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included a discussion on the peculiarity of retorted shale materials to be investigated and a discussion of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I - Program Development II - Exploratory Laboratory tests on old U.S.B.M., retored shale III - Laboratory tests on Pilot Plant retorted shale IV - Laboratory tests on retorted shale from Semi-Works Plant, and field and test plots and ponds. V - Field compaction tests

Jan 1, 1975

By A. D. Davis

Limestone-based material is effective for reducing arsenic concentrations below the current limit of 10 parts per billion for drinking water, typically resulting in final concentrations of about 4 to 6 ppb. However, in laboratory and field testing, further reductions to the 1 ppb range are difficult to achieve with limestone unless other material such as iron is added. The removal mechanism with untreated limestone appears to be the formation of a low-solubility precipitate of hydrated calcium arsenate, in the form of arsenate-apatite. Likely reactions and thermodynamic data indicate a theoretical removal limit of about 2 to 4 ppb for arsenic using raw limestone. Limestone also can reduce concentrations of cadmium and lead below 1 ppb in water, resulting in >99% removal efficiency. Thermodynamic constraints appear to be favorable for reactions involving the formation of otavite during cadmium removal and the formation of hydrocerussite during lead removal.

Feb 27, 2013

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981