Search Documents

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

By Larry G. Stolarczyk

Jan 1, 1980

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By E. P. Youngman

From a scientific point of view , the zircon is by far the most remarkable of the gem stones , and a satisfactory solution of the problems offered by its characters and constitution has not yet been made . 3 Three distinct forms have been recognized , differing in specific gravity , hardness , optical properties , behavior when heated , and color.4 ( See section of this paper entitled "Description and Properties . " ) Zircon as a gem stone has not been as well known as its properties warrant . It is one of the most brilliant of the precious stones (having a high refractive index) . The colorless zircon rivals the diamond in brilliance and fire play to such an extent that a judgment based entirely upon optical inspection might be erroneous . In the opinion of gem authorities , the colored stones likewise have much merit . The blue zircon ( " Starlite" ) was so named by Kunz because of its resemblance to a " star twinkling in the night . " Another gem authority describes the leaf- green stone as one possessing a restful beauty , the red stone as having a certain ( though somber) grandeur , and the golden-yellow stone as being unsurpassed in magnificence . The slowness with which the zircon , a stone frequently mentioned in ancient literature , has come into use in modern jewelery may be owing to the fact that authorities differ as to whether the colorless and the blue zircons are found as such in nature or are treated stones . Any treated stone , although the material of which it is composed may be essentially genuine , has been considered a deception . However , according to Kunz , " Starlite is now sold over the entire world ; never has anything been so well introduced. "7 Dr. Foshag, mineral curator of the United States National Museum, states that the first allotment of zircons to enter the United States was obtained in 1921 from Siam ( through France ) for scientific or museum purposes and that four or five years later the stones were adopted by the jewelers of this country . Retail jewelers are displaying the colorless type and the blue stones , especially , in finger rings , necklaces , and like ornaments . Fine crystals have been used somewhat extensively in jewelling watches and as supports for the edges of fine balances . At one time zircons were though to be appropriate in mourning jewelery .

Jul 1, 1931

The mineralisation consists principally of layered pyrite, phalerite and galena, situated conformably within a sequence of tuffaceous, bituminous shales and dolomitic sediments that include slump breccias. The sediments show little evidence of post sedimentary reconstitution. A volcanic-exhalative-sedimentary origin is postulated for the mineralisation. Attention is drawn to the similarity between the McArthur deposit and the lead-zinc-silver orebodies at Mount Isa. The primitive nature of the sulphides is reflected by their adverse metallurgical behaviour, and it seems that the best prospect for milling and flotation benefication may lie in the production of separate zinc and bulk concentrates

Jan 1, 1968

By M. Somerville, S. Sun

The liquidus temperature and viscosity of a range of melter slags produced in South Africa were determined. Drop-quench experiments were carried out on the supplied plant samples to determine the liquidus temperature and phase relations at sub-liquidus temperatures. The temperature measurement range covered 1300°C to 1630°C. Results from these experiments show liquidus temperatures for the melter slags to be in excess of 1500ºC with the chromium containing spinel as the primary crystalline phase. At lower temperatures, an olivine or pyroxene phase co-existed with the spinel phase. The viscosity of the slags was determined over a temperature range of 1350 to 1550°C, under a controlled atmosphere. Results show two orders of magnitude variation in the viscosity (0.2 to 20Pa s) with strong effects of slag chemistry and temperature. Slags with lower SiO2and Cr2O3concentrations were more fluid. Slags with the lowest FeOx and highest SiO2concentrations were the most viscous. These observations are in accord with general behaviour of silicate slags. While the presence of a spinel phase may have an effect on the viscosity of the melter slags, results obtained to date indicate a much stronger effect due to the presence of an olivine or pyroxene phase at lower temperatures. Keywords: phase equilibria, liquidus, viscosity, slags, olivine, spinel, pyroxene

Jan 1, 2004

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

The applicability of borehole assaying techniques, both conventional and advanced, to orebody evaluation in the mining industry is reviewed and assessed, and the research, development, and demonstration programs necessary to apply the various logging techniques to mining are outlined. At present, the principal method of orebody evaluation in the mining industry is coring. However, coring is costly and time-consuming, and potentially great savings can be realized if all or part of d coring program is replaced by a borehole logging suite specialized to the needs of the particular mining industry. Using a set of 12 minerals, most of which are essential to the U. S. economy, an algorithm is presented for calculating the priority of developing suitable borehole assaying technology to replace all or part of the coring in each mineral industry, The priority is expressed in terms of dollars currently spent for that portion of present orebody evaluation techniques which may eventually be replaceable by in-situ assay techniques. The orebody assay requirements (grades, accuracies, etc.) of the 12 selected mineral industries, as determined from mining industry interviews and published literature, are compiled and represent performance criteria for borehole assaying instruments for the particular industry. Current logging techniques, applied chiefly in the petroleum industry, and advanced assay techniques which are or may be packageable for borehole use are evaluated to determine their performance characteristics. The performance characteristics of the various conventional and advanced techniques are then compared with the performance criteria in each of the 12 mineral industries in order to determine the potential benefit derivable from each technique. Finally, the benefit available from each technique, averaged over the 12 mineral industries, is compared with the cost of development of the technique, to determine the overall priority for investment in research to develop the technique for use in mining. The technology assessment and cost-benefit analysis shows neutron activation analysis in its various forms to have the highest priority for research and development as a borehole logging technique. Other techniques found to be promising include x-ray fluorescence, x-ray diffraction, photoluminescence (optical fluorescence), and infrared spectroscopy. Of the 12 industries considered in the study, those where the need for advanced borehole logging technology is greatest are uranium, copper, gold, and iron.

Jan 1, 1976

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

The phenomenon of surfactant adsorption at mineral surfaces is of significant importance in many particulate processes ranging from mineral flotation and enhanced oil recovery to pharmaceutics, paint technology and the casting of high quality ceramics. Stability of the dispersions is related not only to the amount of adsorbed surfactant but also to the structure of the adsorbed surfactant molecules at the interface. This structure greatly depends on the type of surfactant and the hydrophobicity or hydrophilicity of the surface. On hydrophobic surfaces surfactants adsorb regardless of surface charge by van der Waals/hydrophobic inter-actions with hydrocarbon chains accommodated at the surface. On the other hand, on hydrophilic surfaces the surfactants adsorb through electrostatic interactions with their polar moiety fixed at the surface. In the latter case, the electric charge of the surface and surfactant plays a crucial role in the surfactant adsorption process. The recently developed soft-contact Atomic Force Microscopy technique has revealed images of adsorbed surfactant structures at various interfaces. The adsorbed structures of a cationic surfactant (CTAB) and an anionic surfactant (SDS) are presented in this work for different concentrations at hydrophobic graphite and hydrophilic mica surfaces. Different types of micellar arrangements have been observed at these surfaces for surfactant concentrations around the critical micelle concentration. The structures are more ordered and well defined at the graphite surface than at the mica surface. These results have been correlated with the hydrophobicity of the surfaces as revealed by contact angle measurements.

Jan 1, 2001

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

In spite of the many contributions that have been made to our knowledge of the creep properties of polycrystalline lead, the precise influence of various factors on these properties is not yet fully understood. Indeed, the position is such that several important points in connection with the creep of lead are a matter of controversy. This has been brought about largely by the fact that, in the case of lead, the changes that are produced in the creep behaviour by slight variations of such factors as the purity, grain sizeand previous treatment are out of all proportion to the magnitude of these variations.In order to study the fundamental properties of lead as related to creep, and so gain a more enlightened perspective with which to consider the creep of lead in general, the work that is described in a series of papers, of which the present paper is the third part, has been carried out. It deals with lead in the form of single crystals.It has been shown (1) - (3) that the grain boundaries as well as the actual grains play a part in the creep of polycrystalline lead. The present work, by eliminating grain boundaries, enables the. contribution of the grains themselves to the process of creep, in other words, crystalline creep, to be studied effectively.This object was, possibly, the major one in this work.

Jan 1, 1940

New Zealand depends on foreign investment for economic development. This also applies to the development of New Zealand's mineral resources. For this foreign investment to happen there must be some incentives to attract the investment. While prospectivity is the dominant parameter considered by investors it is not a variable that can be changed, only the perception of New Zealand's prospectivity. Other parameters likely to be considered are sovereign risk, red tape, green tape, land access, civil unrest, land claims, social risk, labour relations, infrastructure and natural disasters. Regulators and political will can vary some of these parameters. Where New Zealand fits internationally can be measured by investors' perceptions of these parameters. Following on from these perceptions New Zealand can be seen to have advantages in some areas and be disadvantaged in others. How to deal with the disadvantages to give investors confidence is not easy in the New Zealand environment where the development of mineral resources plays a small part in an economy dominated by agriculture. Added to this is the current global state of the minerals industry which offers even more of a challenge to attract foreign investment to develop New Zealand's mineral resources.

Jan 1, 2000

By O. C. Blade

Studies on more efficient utilization of petroleum have been made for 50 years by the Bureau of Mines. As part of this work, the Bureau has analyzed thousands of samples of crude oil by its standardized routine method, and many of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published from 1921 to 1959, and brings up to date the information in Information Circular 7470 3 and in the appendix of Bulletin 490.4 The routine method of analysis and the equipment originally were described in a report by Dean and associates. 5 This report has long been out of print, but Bulletin 490, bringing the procedure and its modifications to date, was published in 1951. 6 Briefly, the procedure consists of testing, by standard methods, small samples of a crude oil for gravity, sulfur, color, viscosity, pour point, and (more recently) nitrogen; and, by a standardized procedure, distilling a portion of the crude oil and determining certain properties on the separated fractions and residuum. Careful records are made during the procedure, and the distillation data obtained are used to compute the approximate amounts of products present in the sample--such as percentages of gasoline, kerosine, gas oil, and lubricants. The principal data and results are recorded on a standard analytical report form. An analysis of a sample of crude oil from a recently developed field is shown in table 1. Compilations of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses often are included in connection with other studies, such as engineering field reports.

Jan 1, 1959

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997