Search Documents

By K. V. Raj

As open pit mines continues to grow deeper, managing air pollution can become challenging. During arctic air inversion, the temperature of the air over the mine increases with altitude, and the cold, heavy, surface air is trapped in the pit. This problem is complex, and any solution will require an extensive understanding of the interactions between the aerodynamic movement of air, air inversion, meteorology, pollutant sources, and transport phenomena in the open pit mines. The availability of computational fluid dynamics (CFD) has elucidated the pollutant flow mechanism in open pit mines. Very few CFD studies have been published, especially the Large Eddy Simulation (LES), on the contaminant transport in deep open pit mines under arctic air inversion. The contaminant transport in an open pit mine under arctic inversion is due to a stable or nocturnal boundary layer in micro-meteorological terms. Understanding the physics of the stable boundary layer (SBL) is relevant to air flow and pollutant transport in deep open pit mines. This paper focuses on a Large Eddy Simulation (WMLES as Sub-Grid Scale Model) modeling of the SBL and pollutant transport in a large open pit mine.

Feb 23, 2014

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By S. Yuan

A large-scale work scheduling algorithm has been developed in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. This study basically concerned the formulation of a reliable mathematical programming model to handle the problem, the achievement of an efficient solution of the model, and the implementation of the algorithm to the worker assignment problems of a large underground coal mine. The results showed that the work scheduling algorithm can make optimal assignments efficiently. It is believed it has potential significance in improving manpower utilization and can offer great help to coal mine managers in making efficient manpower allocations.

Jan 1, 1994

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

WHEN one leaves the busy street and enters a library, the closing of the door behind him marks his passage into another world. Outside is the world of phenomena and appearances-of thronging pedestrians bustling about their business, of gregarious sights and sounds, of insistent auto-mobiles. Inside, on dusty shelves, is the stored learning of civilized man-the recorded ideas of countless generations. It is somewhat of a magic world. Here are the theories and secrets for which thousands of men toiled and gave their heart's blood. To produce one book on one phase of an ob-scure-subject may have required the best efforts of a group of men unique in their period. To prove one theory, or es-tablish a single application of a theory, may have taken the devotion of a genius who sacrificed his life to his work. This theory is perhaps stated in one paragraph of unassum-ing type, and the library contains millions of such para-

Jan 11, 1927

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

The coal-based power generation industry faces increased pressure from all sectors to improve its environmental performance. This is due to increased awareness of and concerns regarding greenhouse-and acid-gas emissions, toxic metal releases (to both air and water) and water availability. A methodology to assess this industry?s environmental performance is needed. Such a methodology should assess all environmental impacts accurately, recognizing the irspatial and temporal dependence, and taking into account the social acceptability of technologies employed. Here, we develop a methodology to determine the environ-mental impact associated with solid wastes generated by this industry, and apply this to the specific case of ash management. More specifically, the case study compares the environmental footprint of an ash deposit for a number of operational water management scenarios. The methodology considers leachate generation processes from ash impoundments to obtain a time-dependent concentration profile of mobile constituents at the interface between the ash impoundment and the surrounding environment. This leachate prediction modelling is subsequently linked to plume dispersion modelling tools to determine the fate and transport of leached components, predominantly salts, into groundwater. Together, these provide a measure of the extent to which a land mass is affected by leachate migration from the deposit. To determine the exact boundary between regions of acceptable and unacceptable risk to the environment, we use Ecological Risk Assessment concepts. In this way it is possible to obtain a time dependent affected land footprint which could be used as an indicator of the environmental impact of solid waste management practices. This information can be included in a set of environmental criteria which form the basis of an overall environ-mental impact assessment, using tools such as Life Cycle Assessment (LCA). The value of LCA is that its structure is consistent with accepted models of environmental decision making, where different approaches to valuation in impact assessment assist in prioritizing impacts on the basis of their perceived significance. The proposed ?affected land footprint? metric represents a significant improvement over current LCA impact indicators for solid waste management practices. Keywords: Environmental Impact Assessment, Environmental Risk Assessment; Life Cycle Assessment; coal ash; leachability; salinity

Jan 1, 2002

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017

By C. E. Abbott

THE Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production are as follows: Fe2O3 Si02 A12O3 CAC03 MGCO Lump, per cent 0.51 0.22 98.63 0.14 Crushed and washed, percent 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 7 1/2 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1 ¼ to 0.063 in., is calcined at the, lime-burning plant and used for lime charges at the Ensley open hearths.

Jan 1, 1936

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By Paul L. Tyrna

The Fola Coal Co., LLC No 2 surface mine, located in Nicholas and Clay Counties, WV, exploits up to nine coal seams by contour, highwall, and mountain top removal mining methods. After encountering faults, areas of highly fractured coal, and subsidence failures. the mine requested a lineament analysis from the Mine Safety & Health Administration's (Pittsburgh Safety and Health Technology Center) Roof Control Division. The 31 km2 study area was viewed on a LANDSAT-5 band 4 (near infrared, 0.76-0.90 µm wavelength) satellite image with ERDAS Imagine 8.4 software. The software allows image examination under artificial sun azimuths and elevations, resulting in variable tonal characteristics. The study area image was viewed in 45° azimuthal increments from 000° to 315° at artificial sun angles of 10°, 30°, 50°, and 70°, yielding 32 separate images. The interpretation process developed by MSHA Roof Control personnel identified 16 northeast-striking and one northwest-striking lineament that intersected mine property. Faults and areas of roof instability corresponded well with lineaments identified in the study. Successful lineament identification prompted mine management to incorporate lineament analysis as a mine-planning tool for adjacent property, thereby identifying in advance areas that could adversely affect safety and production.

Jan 1, 2001

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By Wayne Burmeister, Danie Benade, Louis Meyer, Hugo Joubert

What is not measured cannot be managed. This is true of most things, including a furnace lining. This paper describes a Lining Management System used for this purpose. It provides the operations staff with a management tool to predict long term lining life and acts as a process optimisation tool. It alarms and records upset furnace conditions. Outputs from the system are described as presented through a specially developed software package and interface. It includes vertical and horizontal furnace sections showing estimated isotherms through the lining as well as the furnace bath. It also shows calculated heat flux values, estimated lining wear and the freeze layer profile. A novel three-dimensional display is described which provides the operator with a big picture view of the furnace crucible profile under real time operating conditions. The powerful trending facility for analysing both measured and calculated values is discussed. The required instrumentation hardware as well as the installation thereof is described, with special reference to an electrically insulating thermocouple socket design. Finally feedback is provided on the first year?s performance of the system installed on an open ferrochrome furnace at Assmang Chrome, Machadodorp, South Africa.

Jan 1, 2007

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By F. Hassani

This Paper describes a sudden spill of rock waste used for backfilling from a waste pass at one of the underground mine in Canada thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in future. The investigators from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied and appropriate measurements were taken and samples of the waste material was collected for further test and analysis. The field visit and the interview of the witnesses allowed a detail documentation of the events. The sequences of events related to the incident together with the experimental results obtained in the course of the investigation is detailed. The waste material was characterised in the laboratory with regard to its behaviour in the presence of water. This information is then discussed and the failure mechanism involved in this accident is identified. The full recommendation as well as the immediate operational measures implemented by the mine to prevent future occurrence of such events are discussed and presented.

May 1, 2003

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By J. E. Nesset, J. A. Finch

A model of the fully-loaded condition of particle accumulation on the matrix of a high gradient magnetic separator is developed. The model accurately predicts the build-up profiles reported recently by Friedlaender et al. A powerful development from the model is that loading (volume of accumulated material per unit volume of matrix) is uniquely defined by a dimensionless group, called the loading number, NL. From direct measurements, NL proved superior to the dimensionless group proposed by Watson as a measure of loading. The fine size limit of hematite recovery is examined using NL.

Jan 1, 1980