Search Documents

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By N. V. . Panishev

The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.

Jan 1, 2010

By S. S. Klima, A. L. Mazzella, J. S. Driscoll, T. W. Beck

Previous testing was performed by researchers at the National Institute for Occupational Safety and Health (NIOSH) to improve longwall dust control using underside shield sprays with a longwall directional spray system. This testing provided encouraging results toward respirable dust exposure reductions for longwall personnel, achieving as high as 99% dust reduction at some sampling locations along the longwall personnel walkway. Additional laboratory testing was conducted to test these underside shield sprays in conjunction with a shearer-clearer spray system located on the longwall shearer body. The purpose of this testing was to determine if the underside shield sprays interacted positively or negatively with the shearerclearer sprays. Results from this testing indicate that while the shearerclearer system influences where the respirable dust particles are directed, underside shield sprays can still lower respirable dust exposure for longwall personnel.

Mar 2, 2022

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By Wayne F. Luinstra, Frédérique Vincent, André R. Laplante

"A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; possible uses are discussed. A case study of how the technology was used at Hemlo Gold Mines is presented.IntroductionUsing gravity to supplement either flotation or cyanidation is a well established practice in the gold industry. It differs from most recovery circuits in that most of the gold recovered by gravity would be recovered in any case by the circuit downstream, be it flotation or cyanidation. The economic justification of gravity is therefore based on small margins (for example. a net smelter return of gravity gold of 99%, as opposed to 94% by flotation). It was easily demonstrated when either flotation or cyanidation were relatively inefficient processes, and labour costs low (as gravity can be labour intensive). Over the past thirty years, the advent of better flotation machines (flash, column, high capacity), more effective collectors, and better control systems has increased flotation's metallurgical performance, thereby decreasing the incentive for gravity recovery. Cyanidation technology has undergone similar changes, with the advent of activated carbon, oxygen and lead nitrate addition, and improved impeller design.Today, gravity could remain an attractive option only inasmuch as it can be implemented with very low capital and operating costs. This has resulted in a relative shift away from gold gravity recovery (except for alluvial deposits), in the seventies and eighties. For example, as of the early nineties, gold gravity recovery has disappeared from the typical South African flow sheet. The advent of the Knelson Concentrator, at the beginning of the eighties, foreshadowed a resurgence of gravity recovery, as gold's grinding and classification behaviour (Banisi, Laplante and Marois, 1991) makes it possible to achieve adequate gold recoveries with very simple, Knelson based, gravity circuits (Laplante et al., 1994).Consider for example the Hemlo recovery circuit, made of a single 61 cm x 122 cm (2' x 4') screen, an automated 76 cm (30"") Knelson feeding a Gemeni table, to produce a 70-80% Au concentrate which accounts for approximately one fourth of the gold production (about 3 million grams per year). The low capital and operating costs make it possible to justify the gravity circuit on the basis of savings in other operating costs (e.g. fewer carbon stripping and reactivation cycles). Any improvements in recovery, which would at Hemlo be difficult to measure, would be additional benefits. Such a circuit is rapidly becoming a standard in Canadian and Australian operations.The justification for installing a gravity circuit must be first based on an estimate of how much gold it will recover (irrespective of what the potential benefits are). This is a function of the nature of the gravity circuit to be installed; however, Knelson circuits, by their very simplicity and efficiency, limit the options. This leaves the amenability of the ore to gravity recovery as the single most important parameter. Various approaches can be used to characterize this response (Woodcock, 1993). The present work sought a route which would fulfil the following criteria:"

Jan 1, 1996

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemicals are added to flotation circuits directly and indirectly to control issues such as scaling and dust in other areas of the operations. Since dosage levels are generally not high, a standard laboratory float test may not be able to determine the effect of a specific chemical on the productivity of the flotation circuit. This paper presents a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5–100 g/t). Results indicate that this protocol helps to predict potential interference by a particular chemistry on the flotation circuit.RÉSUMÉ Certains produits chimiques ne servant pas à la flottation sont ajoutés directement et indirectement aux circuits de flottation afin de contrôler des problèmes tels que l’entartage et la poussière dans d’autres secteurs des opérations. Étant donné que les niveaux de dosage sont généralement faibles, un essai standard de flottation en laboratoire pourrait ne pas être en mesure de déterminer l’effet d’un produit chimique spécifique sur la productivité du circuit de flottation. Le présent article définit une procédure d’essai en laboratoire qui utilise des études cinétiques de flottation pour vérifier l’effet de doses normales à extrêmes de produits chimiques antitartre et anti-poussière (5 à 100 g/t). Les résultats indiquent que ce protocole aide à prédire l’interférence potentielle d’un produit chimique particulier sur le circuit de flottation."

Jan 1, 2016

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By P D. Katsabanis

Explosives malfunction due to shock waves is a serious concern for successful blasting results. Malfunction includes sympathetic detonation and desensitization of explosive charges as well as the modification of firing times of conventional pyrotechnic detonators.

Jan 1, 1995

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

Sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. The pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors and it was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of the shape factor values with the amount of water used for granulation is discussed in relation to the strength of granules of the sinter mixes.

Jan 1, 1984

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934