Search Documents

By Musa Karakus

In an attempt to explain the phenomena of lead entrainment during Cu drossing of lead bullion, two different synthetic lead bullions were heated to 1050°C, cooled slowly to various temperatures, and then quenched. The morphology and composition of dross particles that form when Mn is used to desulphurize bullion also were examined. Polished sections of these pyrometallurgical products were examined by process mineralogical techniques to identify the impurity phases, determine their chemical compositions, examine the morphology of the impurity phases and evaluate the potential for lead entrainment in such crystals, and characterize pre-quench and quench-generated phases. The phases crystallized were metallic lead, metallic copper, galena, chalcocite, albandite, Cu14.4Pb2S9. and 5.5Pb2S3.5. Metallic copper formed isometric skeletal crystals, chalcocite formed platy and skeletal crystals, and 1formed crystals and eutectic intergrowth with chalcocite and Cu14.4Pb2S9 or Cu5.5Ph2S3.5. The pre-quench crystals are larger and usually exhibit skeletal forms; the quench-generated phases are only a few micrometers across and disseminated throughout the lead matrix. Skeletal crystals of metallic copper and chalcocite form three dimensional networks that entrain large amounts of metallic lead.

Jan 1, 1989

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Farzaneh Sadri

After water leaching of an acid baked REE concentrate, impurities such as Fe, Al, Th, and Cu are removed by neutralization with different reagents such as NaOH, Mg(OH)2, MgCO3, CaO, and CaCO3. Among these chemicals, lime (CaO) and limestone (CaCO3) are the preferred reagents due to their low costs. However, because of calcium sulfate dihydrate (gypsum) precipitation, they are not so common in industry. One of the disadvantages of gypsum precipitation is the adsorption of REE to the precipitates, losing a fraction of REE to gypsum which is hard to recover. In this paper, batch and continuous conditions in the impurity removal process using limestone are investigated and the differences between these two processes are examined. Based on the experiments, REE uptake by gypsum significantly increases in continuous processes, and different gypsum morphologies are observed.

By J. Huisman

With the introduction of ever-stricter environmental operating guidelines, capital expenditure restrictions and operational budget cutbacks, the biological method of SO2 removal becomes more and more attractive. Biological treatment of dilute flue gases is a more cost effective technology in comparison to conventional sodium hydroxide scrubbing. Although the investment costs for sodium hydroxide scrubbing is lower, the operational costs are significantly higher. In addition, the end product of the biological installation is sulfur instead of sodium sulfate; and no further wastewater treatment of the bleed from the biological installation is required since heavy metals are removed simultaneously. Another option for the treatment of SO2 containing gas at a sulfuric acid plant is the production of extra sulfuric acid of the discharged SO2 by applying an additional converter. Comparing biological treatment with this option shows much lower investment costs for the biological installation. Sulfur is produced which can be converted to sulfuric acid, so the bio-route will be more cost-effective than an additional converter. In principle, the biotechnological gas cleaning system is an integration of an absorber with a wastewater treatment facility. In the absorber, the SO2 containing gas is brought into contact with the washing water. The effluent absorber liquid contains a mixture of sulfite and sulfate that is converted into elemental sulfur. This conversion takes place in an integrated system; first, the sulfite/sulfate mixture is converted anaerobically into sulfide; secondly, the sulfide is converted aerobically into elemental sulfur. Subsequently the sulfur is separated and the water is returned to the absorber. Due to the buffer capacity of the washing water, removal efficiencies over 98% are possible. In addition to SO2 removal, it is possible to convert for example other bleeds streams such as scrubber acid or weak acid to sulfur in the same SO2 installation. Recent evaluations concluded that biological desulphurization of flue gases is not only economically attractive in comparison to convention sodium hydroxide scrubbing but also in comparison to gypsum producing systems and even seawater scrubbers. This paper describes the technological and economical viability of biological flue gas desulphurization.

Jan 1, 2005

By J. M. Demarthe

MINEMET RECHERCHE (IMETAL Group, formerly Le Nickel-Penarroya-Mokta) has studied on a laboratory scale and patented a new process to recover metal values -copper- from sulphide ores and concentrates. It combines a cupric leaching, solvent extraction and copper sulphate electrowinning according to the main following steps - A direct and selective leaching of copper sulphide ores or concentrates at atmospheric pressure with cupric chloride to form cuprous and ferrous chlorides and elemental sulphur. Pyrite remains in the sulphur residue. - The leach solution is separated into two parts -In the first one, air is injected to precipitate iron as goethite. The oxidation step can be easily realized at atmospheric pressure by maintaining an excess of cuprous and-ferrous chlorides in the liquor. Copper is extracted from the second part as cupric ion by an LIX reagent. Direct injection or air in the mixing chamber maintains good extraction conditions, so that only one mixer settler is required. - Iron, in the form of ferrous ion, is not coextracted. - Copper is stripped from the organic phase, transferred into a sulfuric phase and sent to sulphate electrowinning cells, which are now conventional in copper metallurgy. - Only electricity and air are required. After a feasibility study, the next step will be to develop it on a pilot and commercial scale.

Jan 1, 1976

By Richard A. Shulkosky

The American Iron and Steel Institute (AlSO, in conjunction with the U.S. Department of Energy (DOE) jointly funded the development of a mechanical properties model for Hot Strip Mills. INTEG process group, inc. validated an enhanced version of the model under a project funded by the AlSI/DOE Technology Roadmap Program (fRP). The Hot Strip Mill Model (HSMM) version 6.0 allows users to easily set-up their mill configuration, simulate a rolling mill schedule and calibrate the model for a variety of grades of steel. Starting from reheat furnace drop out, the model simulates roughing mill stands (reversing and continuous), heat retention equipment (coil box and covers), finishing mill stands (tandem and Steckel mills), the run out table and the mill exit area. The HSMM uses a series of physical models to calculate both the thermo-mechanical and the microstructure evolution of steel being processed in a hot mill to predict its final mechanical properties. The enhanced HSMM was validated using a multitude of samples from several steel companies. Excellent agreement was obtained for tensile strength. The supporting steel companies have utilized the model for a variety of practical applications. Keywords: Process Modeling, Microstructure Evolution, Mechanical Properties

Jan 1, 2003

By James E. McNulty

Today's energy era is the beginning of a transition from the Petroleum Age to a future age of renewable fuel resources. Fuels for the transition era will come from unconventional sources and conversion technology. Affecting the practicability of transition technologies are attitudes of the public, capital requirements and availability, patterns of fuels utilization, producibility of fuels and the actions of governments. Primary energy sources to replace deficiencies of oil and gas and provide growth in the period of transition will be coal, oil shale, nuclear energy and peat.

Jan 1, 1981

By D. Lambert

Process modeling for large deformation metal forming processes has been developed into a very successful tool in commercial applications during the last two decades. DEFOR.MTM is a well-known metal forming process simulation program used by many industrial and research institutions. Recent developments include the ability to model multiple deforming body behavior during multi-pass pack rolling and microstructure prediction during multi-pass shape rolling. This paper summarizes how DEFOR.MTM can be applied to a number of rolling processes and briefly describes preliminary work carried out using the ALE technique. Keywords: Simulation, Rolling, Pack, Shape, Microstructure, FEM, ALE, Tantalum

Jan 1, 2003

By P. Louis

Although cobalt is known and used for its hardness and wear resistance, ductile cobalt can be obtained by electrolysis in chloride solutions, under the following conditions : pH : 1.5 - 2, Co++ : 30 - 60 g/l, current density : 100 - 500 A/m2, temperature 40 - 70°C. No explanation was found for the ductility of the deposit under these conditions. Indeed the ductile P (FCC) cobalt and the hydrogen contents in the cobalt deposits are nearly the same as those obtained in a sulfate media, which gives brittle depo¬sits under equivalent electrolysis conditions. Malleable cobalt sheets can be easily obtained under the proposed conditions which could lead to new applications for cobalt.

Jan 1, 1988

By R. W. Bartlett

The extensive central Idaho black sand placer deposits are a potential source of rare earth elements, particularly the heavy rare earth elements that are not prevalent in commercial bastnasite deposits. These placers derive from the Idaho batholith. The geology, occurrence, and extent of these deposits are reviewed and the diverse mineral assemblages and complex mineral chemical compositions of these sands are described. Niobium, yttrium and thorium are also present in significant concentrations. The results of prior mining practice, including concentration and separation of the heavy minerals are reviewed. Technical approaches to extraction of rare earths from Idaho black sand concentrates are discussed.

Jan 1, 1992

By Klaus Bauckhage

Phase-Doppler-anemometry (PDA)-measurements have to be taken from representative measuring positions from inside the spray cone, helping - with the support of simulated data of improved process models - to describe the multiphase flow situations within the spray cone - and accordingly to that - the heat transfer conditions for the rapid cooling and (partly) solidifying melt droplets before their impact onto the substratddeposit. Simulations and PDA-measurements thus give the base to confirm the hypothesis of the existence of a semisolid mixed-layer and it's influence on the resulting material structure during compaction. The dispersed particles in the spray cone exhibit a cooling and solidification process within a split of a second, which leads - as far as the particles solidify - to a dendritic structure with very short dendritic arm spacings. This causes within the particles extremely short distances for the following equalizing diffision processes taking place on a high temperature level (between liquidus and solidus) in the semisolid mixed-layer of the deposit and explaining the short residence times within this zone of only seconds up to a few minutes. This and the fact that the globular structure of the mushy zone (in the semisolid mixed-layer) leads to an unidirectional crystallization process over very short distances also explains the chemical and morphological ,homogeneity of the sprayed material. The dynamics of these process steps, the very special buffer function of the mixing layer during parameter variations as well as the controlled cooling process of the preform in order to avoid hot cracks influence the quality of the material. Due to the necessity of measuring and controlling the particle bound mass-, momentum- and enthalpy- fluxes to the deposit the PDA-technique has been adapted and modified in order to receive in-line and (in the future) also on-line data from the dynamics of the multiphase flow conditions within the spray chamber.

Jan 1, 1999

By Kenneth C. Mills

Interfacial phenomena can have a dramatic effect on the separation of phases. Furthermore, since they involve surface-active materials, concentrations at ppm levels are enough to cause dramatic effects on separation processes. The effects of (i) emulsification, (ii) contact angle and wettability and (iii) Marangoni flows on phase separation are reviewed.

Jan 1, 1999

By K. J. Richards

The converting of copper mattes to blister copper has seen few technical advances since the introduction of batch furnaces using submerged tuyeres over a hundred years ago. The first side-blown converting vessel, operated by P. Manhes in 1882, was an offshoot of the 'Bessemer steelmaking process, and subsequent improvements in the conversion of molten mattes resulted In the Peirce-Smith converter, still the Industry standard today. While Peirce-Smith' converting has served the industry well since the early 1900!s, increasingly stringent environmental regulations, burgeoning energy costs, and a trend toward continuous processing have set the stage for a major improvement in this area of copper production. In contrast to a growing number of approaches for continuous converting using molten copper mattes, Kennecott is developing a process for treatment of solidified matte which allows improved' control, higher oxygen enrichment and a separation or decoupling of smelting and converting operations not possible with the other converting technologies. The new process known as Solid Matte Oxygen Converting, or SMOC, eliminates the need for molten matte transfers, minimizes fugitive emissions, and produces high strength SO2 off gases which substantially reduce offgas handling requirements. The SMOC process, despite additional matte solidification and size reduction steps, offers both capital and operating cost advantages for new smelters and the upgrading of existing plants, when compared with conventional converting technologies. Capital cost reductions of up to 35% in converting, gas handling, and sulfur fixation are indicated. Kennecott has successfully tested the new process concept and continued' development work is now under way to commercialize the technology. This paper reviews the limitations of batch copper converting with emphasis on the need for a continuous process, previous industry approaches to continuous converting of molten mattes, and the new Kennecott development.

Jan 1, 1983

By Yoshihiko Maeda

It is said that the 21 st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980th due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologies and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By Youn-Bae Kang, Jong-Jin Pak, Min-Kyu Paek

The critical evaluation and thermodynamic optimization of Mn-Si-C and its sub-binary systems have been carried out over the whole composition range from room temperature to above the liquidus temperature. The solution properties of the liquid systems have not been clearly described because the liquid solution exhibits a high degree of short-range-ordering. In order to predict the thermodynamics of the liquid solution, the liquid phases were optimized by the modified quasichemical model. The model parameters of the solid phases were also optimized by the compound energy formalism to best reproduce the phase diagram and important thermodynamic properties in Mn-Si-C system. Using the model parameters, various thermodynamic calculations were carried out. The present database will be a part of larger thermodynamic database for the ferromanganese alloy database.

Jan 1, 2014

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450 °C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By S. Sugiyama, M. Kiuchi

"New metal working processes, such as the mashy-state mixing, mashy-state forging, mashy-state rolling and mashy-state extrusion are developed and applied to manufacture the so-called particle reinforced metals, fiber reinforced metals, particle reinforced cladding metals and so forth. These metal-ceramics composites are made of metal sheets, metal powders, ceramics particles and ceramics fibers. The mashy-state processes are also used to work those composites into bars, wires, tubes, plates, sheets, machine parts and other products. The working conditions necessary to manufacture sound composite products are clarified and the mechanical properties of the products are investigated. Through the investigation, it becomes clear that the mashy-state processes are useful and effective to manufacture metal-ceramics composites. It is al so known that these processes may be applied in various ways to development of new metal matrix compounds. IntroductionThe so-called metal-ceramics composites and processes to manufacture them are now being widely investigated in order to comply with increasing demands for new materials with novel and excellent mechanical properties and functions. The metal-ceramics composites are expected to have superior characteristics with respect to the elastic modulus, hardness, anti-wear resistance, high temperature strength and other mechanical properties to those of conventional metallic materials.The present authors ha v e been investigating into new metal working processes which are based upon the characteristics of metals and their alloys in the mashy-state. In the mashy-state, the metal (or alloy) includes both of the solid and liquid components. According to the fact that the partial melting takes place and the liquid component usually exists at grain boundaries, the metal in the mashy-state has quite different mechanical properties from those of the metal in the solid-state. Because of that the bonding force among grains is very weak due to the partial melting occurred at grain boundaries, the mashy metal has distinctively low flow-stress and high deformability. The mashy metal splits into grains or particles and sticks to others very easily. It is so soft as to be stirred up just like a lump of sherbet, but it is sufficiently viscous to be mixed up with other materials, such as ceramics particles and ceramics short-cut fibers."

Jan 1, 1988

By David J. Krichten

A method of retrofitting air-fuel burners with oxy-fuel capability overcomes the potential problems associated with oxygen combustion in aluminum melting furnaces. The retrofit burner uses the existing combustion air connection, burner housing, and burner tile and replaces the gas tube with an oxy-gas burner. Maintaining a portion of the air flow to the burner reduces the potential for localized overheating. Proper design of the burner reduces NOx emissions by moderating the flame temperature with furnace gas recirculation. Economic analysis of using oxygen shows the benefits are increased productivity and reduced overall unit cost of melting. In practice, the melt rate in rotary furnaces increases by up to 50% and by up to 35% in reverberatory furnaces. Oxygen utilization reduces total melting cost by 112-314 cents per pound of aluminum melted.

Jan 1, 1997

By Ruben Alvarado

The need to increase business competitiveness while complying with environmental requirements represent the great challenge that the Caletones smelter has decided to face in a new development project with a compromising and willing alliance with its workers. To date, the project is at the feasibility stage, with start up scheduled for the middle of the year 2002. The processing capacity of the Teniente Converters will be increased to levels up to 2400 tpd of chalcopyrite-based concentrates containing 30% Cu, by means of more intensive use of oxygen and improved stabilization of the overall operation. Productivity increses in the converting of white metal and the pyrometallurgical treatment of slag are also planned. As a result of related strategies, the productivity of the supporting facilities, included the capacitiy of the sulfuric acid plants, will be increased. An intensive and well-designed labor-upgrading scheme will allow the transformation of every worker into an expert in his working areas, thus becoming an active driving force in technology development. Mechanization, appropiate infrastructure, and complete process control and instrumentation will give to the skilled and motivated personnel the necessary tools in order to attain the highest potential ever reached with the Teniente technology. The necessary investment for this project based on the adding facilities to the existing plant is only a third of that required to reach the same objective for a greenfield plant, thus yielding a very high return on investment.

Jan 1, 1999