Search Documents

By S. E. Khalafalla

A method for preparing ferrochromium alloys containing less than 2 pct carbon has been devised in a single vacuum furnace reactor. This method can conserve chromium and should reduce the capital and energy requirements relative to chromite electrothermal reduction. Reduced products containing less than 2 and as low as 0.01 wt pct carbon were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 ton and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be superior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates Fe3C or Cr3C2. Lime accelerates the. rate of solid state reduction of chromite and can shorten the furnacin1r time at 1,3000 C under vacuum from 13 hours to less than three hours. Additional lime and silica are added to the hot reduced chromite after releasing the vacuum and raising the furnace. temperature to 1, 700° C. Soaking the charge for about 20 minutes gave a button of low carbon ferrochromium alloy beneath a well-defined slag layer.

Jan 1, 1985

By Broggi Andrea

Condensates produced by SiO(g) and CO(g) have a crucial importance in silicon production. Condensation will follow the reactions 3 SiOðgÞ+COðgÞ→ 2 SiO2 + SiC and 2 SiO ðgÞ→Si+SiO2. Solid compounds generated during silicon production contain Si, SiO2 and SiC in different microstructures and amounts. In industrial systems, condensates limit the SiO(g) escape to the off-gas system. On the other hand, they can block the gas flowing from the high temperature zone, hence the necessity of studying an optimized condensation process. This review discusses SiO(g) condensation and its interaction with CO(g). The report gives an overview of the condensates found both at laboratory and at industrial scale. The two main compounds are the Si–SiO2 and the SiOx–SiC mixtures. The hypothesis on the mechanism of formation of SiC–SiOx condensates is presented through a wide selection of performed works. The advantages and disadvantages of the former experimental procedures are discussed.

By John J. Mazza

Treatability studies were performed to determine the effectiveness of two commercially available treatment methods (solvent extraction and thermal desorption) for the removal of PCBs and PAHs from contaminated dredged riverbed sediments. The solvent extraction method evaluated was the B.E.S.T. process which extracts the contaminants with triethylamine. The thermal desorption method utilized was the ATP process which desorbs the contaminants at elevated temperature in an anaerobic atmosphere. A description of both methods and. an evaluation of the treatability study results is provided. Each treatment method was used to treat two separate samples (high and low concentration) from the site. Overall, both methods proved to be very effective with solvent extraction achieving 98% removal of both PCBs and PAHs and thermal desorption achieving better than 99% removal of both the PCBs and PAHs from the high concentration sample. Both solvent extraction and thermal desorption achieved greater than 99% removals of PCBs and PAHs from the low concentration sample. Vendor cost estimates for full scale treatment were roughly equivalent. The primary differences between the two methods lies in the realm of permitting, operational requirements, and emission concerns.

Jan 1, 1994

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By Z. M. Zheng

Cyclic voltammetry, potential step, and ac impedance techniques were applied to study the electrochemical reaction of arsenopyrite in chloride solutions. The relationship between anodic current density and time in potential step measurements indicates that the oxidation of arsenopyrite is irreversible. The results of the constant potential coulometry show that the stoichiometric factor of the total electron involved in the overall reaction is 14. It is proposed that the dissolution of arsenopyrite is retarded by coverage of sulfur produced in the reaction as an intermediate product. The measured results of ac impedance strongly support the proposition. The proposed reaction mechanism also explains satisfactorily the charging current density and Tafel slopes measured in potential step measurements.

Jan 1, 1995

By P. A. Metz

The Fairbanks mining district has produced in excess of 7.5 million troy ounces of placer gold and 250,000 troy ounces of lode gold since gold was discovered in the area in 1902. The Fairbanks mining district is in the northwestern part of the Yukon-Tanana Upland Schist Terrane, an area of approximately 240,000 square km that has produced in excess of 21 million troy ounces of placer gold. All lode gold production from the terrane has been from the Fairbanks mining district, and all of this production has come from high-grade gold-quartz polymetallic sulfide veins. Gold grains in the vein systems range in size from several microns to several millimeters. The veins are localized in a complex metamorphic rock assemblage which includes greenstones and felsic metavolcanic and volcaniclastic rocks, meta-exhalatives and metasediments. Gold occurs in the metamorphic host rocks in association with arsenopyrite and arsenic-antimony sulfides which occur in lenses and disseminations within the host rock. Gold grains occurring in the metamorphic host rocks range. in size from sub-micron to a few microns in diameter.

Jan 1, 1987

By Houyuan Liu

A new process was developed to recover nickel and cobalt by leaching laterite ore at atmospheric pressure and.95"-105" C. The nickel-containing goethite in limonite was first leached with sulphuric acid to liberate over 90% of nickel, cobalt and iron. The dissolved iron was then precipitated as Ni-free goethite by the additioil of saprolite. The acid released during iron precipitation as goethite was simultaneously used as lixiviant to leach saprolite to recover more nickel. With this process the limonite and saprolite were essentially converted into goethite-, gypsum- and silica- containing tailings. Twenty bench scale tests and two campaigns of pilot plant operation were carried out at BHP Billiton's Newcastle Technology Centre (NTC) from January to August 2002. The overall nickel and cobalt extractions were 81 to 90% and 91 to 100% respectively. The average plant availability was 99%. The advantages of this process over existing processes include high plant availability, high consistency, robustness and simplicity of the operation.

Jan 1, 2004

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999

By Liming Wang

One of the steps in the extractive metallurgy of lead is a refining process called drossing. Hot dross is mixture of impurity compounds that form on the surface during the cooling of lead blast furnace bullion, and in Missouri, the main impurities are copper and sulfur. The slow cooling of bullion throws out of solution all other minor impurity elements (or their compounds) which are much less soluble at lower temperatures (mainly nickel, arsenic, iron, and zinc). The transfer of bullion from the blast furnace to the refinery and the subsequent hot drossing step cause fugitive emission of lead-containing fume and dust, which creates a plant hygiene problem. One cause of the emissions is the high vapor pressure of lead and its compounds during transmission of = 1000 °C bullion to the drossing kettle. Another cause is the lifting of dross dust during manual skimming of dross. The environmental problems associated with the traditional hot drossing process provided an incentive to investigate a new drossing process that avoids contact between plant air and hot bullion or dross. A key aspect of the process development was a detailed mineralogical examination of dross from two different bullions. The bullion samples were cooled at different rates, and the dross filtered out and examined. The morphology, phase identification, and composition of the dross was examined by optical and SEM microscopy. The principal dross phases were copper and cuprous sulfide, galena, a complex sulfide containing copper, nickel and lead, and speiss (containing nickel, cobalt, iron, copper, lead, and arsenic compounds). The copper was acicular, with nickel and arsenic in solid solution. The cuprous sulfide was largely digenite in a granular or dendritic form. A substantial part of the dross was solidified matte with a eutectic microstructure, consisting mainly of CU2S and PbS. Small particles (some of which had a eutectic microstructure) never floated to the surface of the lead during the slowest cooling rate, thus indicating that flotation of tiny matte droplets and dross crystals is exceedingly slow. The success in separating dross and lead by centrifugal filtration suggests its application in industry as a replacement for traditional hot drossing.

Jan 1, 1995

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Edgar Peek

Lixiviant regeneration is by definition a precondition for any hydrometallurgical process. In chloride hydrometallurgy either HCl or Cl2 has to be regenerated in order to establish an economically viable metallurgical process. One such regeneration process is widely used with steel pickling where HC1 is regenerated through the thermal decomposition of ferrous chloride in either spray roasters or fluid bed pyrohydrolyzers. This standard HC1 regeneration process deserves to be considered as a potential separation process, since thermodynamic calculations show that a fluid bed pyrohydrolyzer can function as a ferrous-nonferrous separator. Several nonferrous,metals such as zinc, lead and cadmium can be volatilized as a chloride under ferrous chloride pyrohydrolysis conditions. If such a nonferrous metal volatilization could be achieved in the case of slurry feeding of "contaminated" iron oxides, then this would increase the Fe/H2O ratio of the (process) feed and thus save on fuel per ton of iron, while yielding a marketable iron oxide product. Previous test work on synthetic materials revealed that the near-complete separation of zinc, lead and cadmium from iron oxide was possible in a pyrohydrolytic atmosphere, even if zinc was present as zinc ferrite (more than 99.5%). This investigation, which was carried out in a tube furnace at 1100 K has now been extended to treat synthetic zinc minerals and also franklinite ore. For the latter, it was found that 85% zinc volatilization could be achieved in 4 hours at 1300 K. It is postulated that complete zinc volatilization could not be attained due to the formation and/or presence of gahnite and hardystonite, which might be stable in HCl/H2O atmospheres at 1100 K. The effect of adding small amounts of calcium chloride to react with gahnite and hardystonite to give zinc chloride and both calcium aluminates and silicates is being discussed. Test work on slurry feeding of this complex ore in a recently constructed 4-inch diameter fluid bed pilot unit has been planned for the near future.

Jan 1, 1995

By D. Lui, B. G. Thomas, B. Ho

"Results from mathematical models and plant experiments are combined to quantify the effect of transverse depressions and oscillation marks on heat transfer in the continuous casting mold. A heat transfer model has been developed to calculate transient heat conduction within the solidifying steel, coupled with the steady-state heat conduction with the continuous casting mold wall. The model features a detailed treatment of the interfacial gap between the shell and mold, including mass and momentum balances on the solid and liquid powder layers. The model predicts the solidified shell thickness down the mold, temperature in the mold and shell, thickness of the resolidified and liquid powder layers, heat flux distribution down the mold, mold water temperature rise, ideal taper of the mold walls, and other related phenomena. The important effect of non-uniform distribution of superheat is incorporated using the results from previous 3-D turbulent fluid flow calculations within the liquid cavity. Results from plant experiments confirm that transverse surface depressions and oscillation marks form at the meniscus and move down the mold. Measurements of mold thermocouple temperatures and breakout shell thickness were used to calibrate the models. The results indicate that the surface depressions and oscillation marks are filled with mold flux, but still have a significant effect on decreasing heat transfer. The predicted mold temperature fluctuations are consistent with measurements. If the depressions become filled with air, their effect is greatly increased. These results should be useful in the difficult task of interpreting transient mold thermocouple signals for on-line quality monitoring.IntroductionMany different types of intermittent surface defects on steel slabs arise during initial solidification in the mold of the. continuous casting machine. These defects include deep oscillation marks, surface depressions, and cracks. They may lead to quality problems, such as slivers, in the final rolled product. In severe cases, breakouts may occur, where liquid steel bursts through a thin section of the shell and drains over the casting machine below the mold."

Jan 1, 1997

By Gaifeng Xue, Xiaohong Xu, Meng Liu, Yijie Song, Guotao Xu, Jixiong Liu

BN (Boron Nitride) based composites were prepared with hot-pressing by using h-BN as main material in ceramic preparation process. The relative density, bending strength, vickers’ hardness, thermal shock resistance, thermal expansion coefficient, thermal conductivity, phase composition and microstructure were tested and analyzed by using modern testing technology. The results indicate that the best formula is B, the relative density is 97%, the bending strength is 260 MPa, the hardness is HV5 343kg/mm2, the thermal expansion coefficient is 2.8×10-6℃-1, the thermal conductivity is 22 W/(m.K) and have no crack after thermal shock for 20 times by water cool. XRD analysis indicates that the main phase compositions are h-BN, β-Si3N4 and sialon. SEM studies show that the grains wrapped up by solid solution.

Jan 1, 2015

By Mahesh C. Meyer Jha

AMAX has developed a chloride refining process to produce pure nickel and cobalt metals from mixed sulfide .precipitates, Metal chloride solutions, generated in a hydrochloric acid leaching step and purified in a solvent extraction circuit, are converted to metal oxides .and HCI gas by pyrohydrolysis. A pilot plant consisting of a 30-inch diameter fluidized bed reactor and other ancillary units was designed, constructed, and operated for over one year. Process design was aimed at minimizing energy consumption, maximizing conversion efficiency, and achieving simplicity of operation and control. The operation provided valuable information on process scale up parameters, process control strategies, and materials of construction., Several process variables such as bed temperature, solution composition, solution feeding system, bed particle size distribution, and fines recycle system were investigated to determine their effects on process efficiency and the physical and chemical characteristics of the product.

Jan 1, 1985

By O. Barbosa F.

The thermochemistry of the systems SCN-H2O, Au-SCN-H2O and Ag-SCN-H2O is discussed. Potential-pH diagrams at 25°C are drawn for each system considering several sets of concentrations of the species involved. The information provided by the potential-pH diagrams is.complemented by distribution curves for each series of gold and silver complexes with thiocyanate. The analysis includes comparisons between the thiocyanate systems and the analogous cyanide systems, pointing out analogies and differences between the leaching of gold and silver with thiocyanate and with cyanide. The possibility of using soluble oxidizing agents such as ferric ions, hydrogen peroxide and Caro's acid is evaluated. The thermodynamic data used in the calculations and the chemical reactions represented in the Pourbaix diagrams are all reported in three Appendices. The overall results indicate the thermodynamic conditions for gold and silver leaching by thiocyanate.

Jan 1, 1989

By T. T. Chen

Hydrometallurgical products are difficult to characterize because of their fine grain sizes, heterogeneity, often amorphous structures and water soluble or hydrated constituents. Such products are advantageously studied using complementary mineralogical techniques including >50, ore microscopy, SEM-EDX, electron microprobe analysis, selective leaching and wet chemical analysis to determine the phases and their morphologies, to identify specific element carriers, and to elucidate the chemical reactions occurring during the metallurgical process. Sample preparation is an important consideration for these materials. For extremely fine-grained particles, or soft and brittle products such as elemental sulphur, the study of loose powder mounts provides information not available from the examination of polished sections. To demonstrate the application of the various mineralogical techniques, commercial zinc roaster calcines and leach residues, copper refinery anodes and anode slimes, and laboratory bornite leach residues were examined in detail. The various sample preparation and mineralogical methods are presented, and the use of these complementary and practical mineralogical techniques to improve the understanding of a particular hydrometallurgical system is discussed.

Jan 1, 1989

By Fatma Arslan

Alada (Kayseri-Turkey) lead-zinc sulfide-oxide ores contain 10.17% Pb, 10.98 %Zn, 164 g/t Cd and 57 g/t Ag. During the laboratory scale flotation tests of these ores, it was found that almost all zinc was remained in the tailings that contain 12.31% Zn, 1.35%Pb, 198.3 g/t Cd, and 22.3%Fe. Three different methods were studied such as basic (NaOH) leaching, roasting+acidic (H2SO4) leaching and direct acidic (H2SO4) leaching for recovering metals that these tailings contain. In the direct acidic leaching, which gave the best results, dissolution efficiencies of 91.5% zinc, 78.2% cadmium, and 14.3% iron were reached at the optimum leaching conditions while Pb remained in the leach residues and the acid consumption was 422.3 kg/ton of tailings.

Jan 1, 2006

By R. W. Lawrence

A method by which it is possible at an oxidation potential below 680 mV SHE to achieve quantitative conversion of sulphide sulphur to elemental sulphur instead of sulphate in a biological leach of chalcopyrite and bornite has been investigated. The process chemistry, biological phenomena and process flowsheet options are discussed. Several copper concentrates have been evaluated and have been found to be amenable to th process. Results to study the progression of chalcopyrite decomposition during the leach are presented and mineralogical factors affecting the requirement for silver addition are discussed. A chloride addition method for improving silver recovery is described. The results of a small scale continuous leach test have demonstrated that continuous operation can be carried out with high copper extraction and stoichiometric conversion of sulphide sulphur to elemental sulphur.

Jan 1, 1985

By Richard D. Hagni

The techniques of reflected light microscopy and cathodoluminescence microscopy are uniquely suited to the study of the products from many important industrial problems. Ref1 ected 1 ight microscopy provides the means to rapidly identify the mineralogy of an industrial sample, determine the abundance of each phase, and examine the mineral intergrowths or textures. Cathodoluminescence microscopy is a relatively new instrument that provides the means to cause many minerals to cathodoluminescence under the microscopy. The cathodoluminescence of a mineral allows it to be readily distinguished from other phases that differ in cathodoluminescence but are similar in optical properties. Cathodoluminescence microscopy is especially useful to detect cathodoluminescence minerals that are present in only small quantities. Reflected 1ight microscopy and cathodoluminescence microscopy have been successfully applied in studies of beneficiation products, prediction of beneficiation and leaching problems, phosphatic iron ores and mill products, pyrometallurgical products, roasted refractory gold-bearing sulfides, ceramic build-ups, electric arc furnace and smelter dusts, and other industrial products.

Jan 1, 1993