Search Documents

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Carlos A. Nogueira

Spent Ni-Cd batteries contain in the electrode materials heavy metals like Ni, Cd and Co, which must be recycled due to environmental problems. Pyrometallurgy is normally used for recycling these end-of-life products, but alternative processes by hydrometallurgy, integrating also physical operations, can be used. Hydrometallurgy seems to be useful, because metals can be efficiently recuperated in chemical forms with commercial value. The economical viability of this recycling process can be improved increasing the treatment capacity, through the application to different types of residues with similar characteristics like Ni-MH and domestic batteries, or other residues containing Ni/Co, like sludges, dusts or spent catalysts. Spent Ni-Cd batteries were first physically processed using shredding and wet sieving operations. Best results were achieved using an output of 6 mm in the shredder and 1.4-2 mm in the physical separation by wet sieving, resulting a fine fraction containing 70% of the initial electrode material and only 6% of the initial scrap. The acid leaching of the obtained material in the previous operation was studied, being the parameters like: temperature, H2SO4 concentration and the liquid/solid ratio (L/S) optimized. The values attributed to the factors which concerned the best results obtained on the leaching process were mainly influenced by Ni recovery. In opposition, Co and Cd were easily leached in a wide range of conditions. To attain an overall recovery, with minimum costs, of the three metals, the values of T~100ºC, [H2SO4]=2.3-2.7 M and L/S=8-10 L/kg were considered the most appropriate.

Jan 1, 2006

By C. J. McKee

A gold-silver-lead-zinc deposit at Montana Tunnels, Jefferson County, Montana is located in a diatreme of middle Eocene age (45 to 50 m.y.). Sulfide minerals within the diatreme occur as disseminations, veinlets, and locally as breccia matrix. Principal sulfide minerals are pyrite, sphalerite, and galena. The diatreme is a matrix-rich quartz latitic breccia with a fine grained rather soft matrix and heterolithic clasts. The ore deposit contains approximately 50 million tons of ore at a grade of 0.025 oz/ton Au, 0.5 oz/ton Ag, 0.25 % Pb, and 0.65 % Zn. Mining is by open pit methods. The original process flowsheet included flotation and cyanide leaching. Problems with the leaching circuit led to a change to the straight flotation process which is presently in use. To maintain a reason-ably uniform feed material, blending of ore is required for grades of four metals as well as for ore hardness and oxidation.

Jan 1, 1988

By John Wallace, Chib Iheagwara

"Refinements in sensor design have produced low-cost rugged elements to act as loop coupled with stable detection hardware for eddy current measurement in difficult environments. This has allowed direct dimension gauging of nonferrous and ferrous products above the curie point for absolute dimensions and electrical conductivities independently. The software was developed for the analysis of electrical conductivity profiles in CZ silicon crystal growth, then refined for monitoring bar properties and tube properties. Since in most metal working operations, speeds at the minimum of a few hundred feet per minute are encountered the design of the gauge was optimized for a rapid measurement. Independently extracting electrical conductivity provides data in some metal systems for determining the temperature of the monitored product.IntroductionThe primary reason for the use of eddy currents in gauging is that in hostile environments of metal working techniques such as laser gauging and ultrasonics are not always robust enough for in process measurements. Our goal is to use the technique of eddy current measurement as a quantitative control element in various hot and cold processing operations. Inspection in the early stages of metal and semiconductor processing is usually too costly to introduce in a well developed process and these tools are usually only employed in process development. Until recently there has been no efficient general analysis to allow real time measurements in the cylindrical and the probe geometry that could separate dimensional changes from material property changes both which effect the eddy current response. The basis for these measurements is that forward electromagnetic problem for conductors can be solved exactly for the test geometry which allows an inverse analysis to be made by relaxing the dimensions and conductivity to values which reproduce the measured response[!]. This transformation is based on analysis developed in Robert Siegfried' s thesis and was explored both by modeling and by physical measurement. This analysis was extended over the last few years to allow a more compact data set to be used to exact physical properties. The main result was that the technique would work on high ·quality physical data on as little as three test frequencies with the penalty being that the analysis is computational intensive. The main result of this work was that a quantitative inverse analysis of eddy current response would allow a general instrument to be used for a variety of measurements rather than being tailored for a specific measurement on a specific material test geometry. The development of these instruments has progressed over the last ten years for monitoring real time solidification, crystal growth[2] and hot seamless tube forming where the use of standards in traditional eddy current is limiting. The specific instrument design was dictated by the requirements of the algorithm for both frequency selection and levels of systematic noise that could be tolerated. Because the data is need for real time information this dictated that the system be a parallel multifrequency eddy current instrument feeding the same sensor. The sensor have to be simple and robust and usually a single loop or several loop of heat resistant wire or tube. This presentation is about using inversion of multifrequency eddy current data in real time to produce dimensional and property data on cylindrical conductors and planar conductors in real time. The object of the measurements is to produce dimensional outputs on measurements of conducting material without having to establish a detailed standard for each material or size tested. The dimensional measurements using eddy currents is complicated by material variations in conductivity due to temperature and composition. Those variations that are not geometric are often not of critical interest and complicate the measurement. The dimensional changes are often of more importance"

Jan 1, 1997

By S. J. Hogan, T. William

"By the year 2000, the steel industry, not only in the United States but in the rest of the world, will undergo significant changes. On the other hand, there will be a number of areas in which change will be minimal.The current capacity of the industry worldwide is approximately 800-810 million metric tons. This may grow to some extent, as Third World countries install capacity. However, much of it will be neutralized as the industrialized countries shrink their current capacities.There will be several breakthroughs in terms of technology, some of which deal with the production of iron outside of the blast furnace. However, these processes will not be far enough advanced by that time to replace the blast furnace, rather they will supplement it.In terms of steelmaking and the subsequent rolling process, there should be a number of basic improvements. The strip mills will roll sheets with a very slight variance in gauge, which will give the customers a better product for automatic stamping machines. Ordinary carbon steel, in a number of instances, will be replaced by high-strength, low-alloy steel, which will reduce the tonnage necessary for present-day applications, such as construction.The corporate organization will be significantly changed as joint ventures and mergers will reduce the number of companies, as well as facilities in operation. This will enable the industry to reduce its capital investment and improve operating costs, so that it will be able more effectively to compete with other materials, such as plastics, cement, aluminum, etc."

Jan 1, 1988

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By P. Balachandran

The paper outlines the existing facilities and working practices at the Khetri electro-refinery of Hindustan Copper Limited. Plans have been drawn up to mechanize some key operations to improve the quality of cathodes and the working environment as well as economize the refinery operations. The economic analysis for determining various optimum operational parameters under conditions existing in India have also been outlined. The impact of capacity utilization and mechanization under different sets of conditions on operational costs have been highlighted.

Jan 1, 1987

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By Makoto Ohlsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SME). The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force. The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films. The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a Ni50Mn25Ga25 or Ni52Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace. The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains. After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature. The martensitic transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated. After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found. The constraint-aged films also showed the two-way 3ME by thermal cycling.

Jan 1, 2003

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By Zuhair A. Munir

"The use of self-propagating combustion reactions to synthesize metallic, ceramic, and composite materials is described. The limitation of this process because of the porous nature of its products is discussed. The formation of dense bodies through the simultaneous application of pressure is shown for a metal-matrix composite. The effect of an external electric field on the synthesis of ceramic and composites is described. The nature of the effect of the field on the mechanism of synthesis is analyzed theoretically and experimentally. The use of the self-propagating combustion to synthesize intermetallic thin films is presented for the Ni-Al and Ti-Al cases. The formation of functionally gradient materials (FGM) by centrifugally-assisted self-propagating high-temperature synthesis is described.IntroductionThe use of self-propagating combustion reactions for the synthesis of a large number of simple and complex materials has been described in numerous publications. These have been amply discussed in several review articles [1-4]. The many benefits of this method of materials synthesis are commonly examined in light of its most significant limitation: the porous nature of its products. The porosity in the products of self-propagating high-temperature synthesis (SHS) is an intrinsic characteristic of the process and its elimination has been the focus of numerous attempts. Various experimental methods have been used to accomplish this goal."

Jan 1, 1994

By Gabriel Riveros

The stags from the Teniente Converter (TC) have high copper and magnetite contents. The reduction and copper impoverishment of these slags in an electric furnace was simulated in the laboratory, as part of a conceptual study for the Ventanas smelter of ENAMI. The effect of power input, electrode immersion, temperature of the slag, coke and solid revert additions on the rate of magnetite reduction and copper recovery was investigated. It was found that the addition of solid reverts, containing copper matte, enhanced the recovery of copper. Magnetite stratification and a corresponding gradient of the copper content occurred in the slag. Microscopic examination of slag samples showed the presence of copper in the form of matte and metallic copper inclusions. The results of the experimental work combined with an analysis of the phenomena that take place in an electric furnace led to a better understanding of the slag cleaning mechanism. The successful start-up of the slag cleaning electric furnace at the Ventanas smelter resulted in good copper recovery and confirmed the beneficial effect of solid reverts addition. Electrode consumption is lower than anticipated. No bottom build-up problems have been experienced. Keywords: copper, slag, magnetite.

Jan 1, 2001

By Tao Xuea

Gold frequently occurs in nature in the form of a gold-silver alloy. Thus, investigation of the electrochemical behavior of gold-silver alloys in cyanide solution has practical significance. In this paper, the potentiodynamic method is used to determine the anodic polarization curves of gold-silver alloys (Au-10% Ag and Au-50% Ag) in cyanide solutions. To facilitate the interpretation of the results, complementary experiments conducted in NaOH solution in the absence of cyanide are also reported. The results for the Au-Ag alloys are compared with the polarization behavior of pure gold and pure silver. With the aid of potential-pH diagrams for the Au- and Ag-CN-H20 systems and electrochemical kinetics concepts, the dissolution mechanism of gold-silver alloys, the effect of the presence of silver on the cyanidation of gold, as well as the factors which control the anodic reaction rate are clarified.

Jan 1, 1998

By J. K. Brimacombe

Plant trials have been conducted at the Tacoma Smelter of ASARCO to assess the effect on tuyere blockage and refractory erosion at the tuyere line, of increasing the injection pressure of air into a Peirce-Smith con¬verter. Four tuyeres each having an ID of 19.1 mm (3/4 in) were installed toward one end of the tuyere line of the No. 4 Converter. Air and oxygen-enriched air were injected at 414 kPag (60 psig) through these tuyeres and at the usual 83 kPag (12 psig) through the remainder of the tuyeres in an otherwise normal converter campaign. The test campaign consisted of 88 charges and lasted for 89 days. During this period, punching of the high-pressure tuyeres was found to-be unnecessary; and when, as a precaution, the tuyeres were cleaned by hand at the end of a charge, they were always open. Also it was observed that the flow of high-pressure air remained constant. Accretion formation around the tip of the high-pressure tuyeres varied from charge to charge and was influenced by the matte grade and the level of oxygen enrichment.

Jan 1, 1983

By Makoto Ohtsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SMB), The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force, The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films, The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a NisoMn2sGa25 or Nis2Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace, The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains, After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature, The martcnsitie transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated, After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found, The constraint-aged films also showed the two-way 5MB by thermal cycling,

Jan 1, 2003

By T. J. White

Each year, thousands of tons of toxic concentrates are produced as the unwanted byproducts of industrial operations and smelting activities. The fate of these materials remains open, as in general their consumption is limited and potential markets contracting. Xtaltite (pronounced crystal-tight) is a Synthetic Mineral Immobilization Technology (SMITE) optimized for the concentration, detoxification and consolidation of toxic metal wastes. In this approach, we seek to mimic nature to produce durable synthetic minerals that survive for aeons in well characterized geological settings. This approach has high public acceptability because the concept is easily understood by the layperson and the long term stability of the waste form may be predicted with confidence. In addition, where Xtaltite is used for mine backfill, a system of ecologically sustainable mining development is established. This paper details the design and fabrication of Xtaltite under oxidizing and reducing conditions. To illustrate and contrast these stabilization regimes, specific reference will be made to the treatment of thallium, chrom~um and arsenic wastes. Waste form performance under TCLP, dynamic boiling water tests and in other leaching media will be compared and discussed with respect to their relevance to different disposal options.

Jan 1, 1995

By Joseph C. Milbourne

Tetra Technologies CCIX? (continuous countercurrent ion exchange) system has been involved in a wide range of uranium concentration, separation and purification applications over the past 40 years. Uranium ion exchange applications have ranged from the treatment of copper heap leach solution containing 5 parts per million of uranium to the treatment of high strength sulfuric acid solutions containing several thousand parts per million of uranium. The flexibility and the countercurrent mode of operation and other unique features of the CCIX? have resulted in successful uranium recovery from these solutions and many others.

Jan 1, 1995