Search Documents

By David B. Spencer

This paper describes a process for separating non-ferrous metals such as aluminum, copper and zinc, from other residential and industrial waste by means of permanent magnets. Although the separator may be used in the recovery of non-ferrous metals from auto scrap, most of the testing to date has been aimed at recovery of non-ferrous metals from municipal solid waste, especially recovery of aluminum from the heavy fraction of a resource recovery plant. In most resource recovery plants the incoming solid waste material is first shredded and then air classified into a light and a heavy fraction. The light fraction which contains mostly paper, cardboard, etc., can be used either as a fuel for power generation or in the production of new paper products. The heavy fraction which remains consists mostly of glass, ceramics, wood, ferrous metals and non-ferrous metals. The ferrous metals may be removed from the heavy fraction by conventional magnetic separators. After primary shredding, most of the glass and ceramic is fine in size and may be screened away leaving a residue of wood, cardboard, and non-ferrous metals. This residual heavy fraction is the input material for the separator described in the present paper.

Jan 1, 1975

By John Newby, Ulf Gwildis, Fred Marquis

From the Brightwater Conveyance System in Seattle to the Second Narrows Water Supply Tunnel in Vancouver, BC, the design and construction of deep-lying tunnels in the Pacific Northwest often require the incorporation of deep portal shafts. Alluvium overlying marine and glacial deposits combined with the high regional seismicity is the common geologic setting. The latest example illustrating the development of shaft design for this scenario is the 40-m-deep shafts of the Annacis Island Wastewater Treatment Plant New Outfall System. The main components of the shafts include the initial lining, providing the excavation support system to be used for launching and receiving a 5-m-diameter TBM; and the final lining, designed to withstand all static and seismic loads and to remain viable for the intended design life. This paper presents design and construction considerations for these shafts against the background of and lessons learned from past project experiences.

Jun 13, 2021

By Adam Saylor, Travis A. Shoemaker, Steve Miller

Lidar scanning has become an increasingly popular tool for documenting underground excavations; however, high costs of traditional mechanical electrical lidar hardware, software, and training have limited the frequency at which lidar scans can be performed. Additionally, traditional scanning can be time consuming because multiple scan positions are necessary. With Apple’s incorporation of low-cost mobile solidstate lidar on select smartphones and tablets, lidar is becoming more tractable for everyday construction documentation similar to construction photo collection with smartphones. Here, we describe benefits of mobile solid-state lidar and describe several practical applications for use in underground construction, such as documenting the working face, over-blast, and geologic features of tunnels.

Jun 13, 2023

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By Joan Carles Casado Ortega, Mitchell Gerdtau, Sandeep Pyakurel, Eric Crocker, Frank Perrone

The Parallel Thimble Shoal Tunnel (PTST) project is a part of the Chesapeake Bay Bridge- Tunnel (CBBT) complex. The project involves the construction of a two-lane bored tunnel under the Thimble Shoal Channel between Portal Island #1 (the southernmost island) and Portal Island #2. The new PTST will be the rst transportation tunnel constructed in the Mid-Atlantic region by a tunnel boring machine (TBM). This paper describes the design and construction of the tunnel approach structure in an open marine environment with the strategies employed to overcome the various construction challenges. The project is unique since the entire tunnel approach structure is built on a very limited area within an open marine environment without any reclamation of the existing island.

Jun 23, 2024

By J-Y Chen

China was once deficient in nickel and almost totally reliant on imports for its domestic needs, supplies mainly coming from Canada since the ending of imports from the U.S.S.R. in early 1960's. However, the discovery of the huge nickel/copper sulphide deposit in Jin Chuan, Gansu Province of northwestern China in late 1950's and its development and construction through the 1960's and 19701s, have much improved China's domestic nickel position. In 1985. China's nickel production has exceeded 27.000 tons, compared with only 7,000 tons in 1977. Today, Jin Chuan Nonferrous Metals Company operates two underground mines and a small open- pit; owns China's largest reserves of nickel and platinum, and the second largest reserves of copper and cobalt; and has become the most important subsidiary of China National Nonferrous Metals Industry Corporation (CNNC) which was established in April 1983. The Jin Chuan nickel-copper mines are located in Jin Chang City, Gansu Province, 1,700 km west of Beijing in the People's Republic of China (Figure 1). It is believed that Jin Chuan mines have the second largest nickel reserves in the world, after Sudbury basin, Canada. The deposits are situated on the north slope of the Longshu Mountains, 50 km north of Jin Chang City, and border on the southmost edge of the Gobi Desert plateau. The deposits were discovered in 1958. The total strike length of mineralized zones was approximately 6.5 km long, which was divided into four mining areas by faults (Figure 2). The Longshu underground mine of No. 1 mining area began development in 1959, with full ore production capacity of 1,000 TPD. The open-pit, also in No. 1 mining area, which was brought into operation in 1966 with ore output of 5,500 TPD, was closed down in 1982. The East Extension of the open-pit was put into operation in 1983; present production capacity is about 2,200 TPD. Nickel production of Jin Chuan mines in recent years, and production capacity of each mining operation, are shown in Tables 1 and 2.

Jan 1, 1987

By M. B. Mooiman

It has recently been discovered that the pH at which gold can be extracted from cyanide solution with primary, secondary, and tertiary amines can be increased 2 to 5 pH units by the addition of modifiers. Under these circumstances gold can be extracted at pH values from 9 to 11, commensurate with the pH range found in cyanide leach liquors. The selectivity of the amines and amine/modifier combinations for AU (CN)[-2] over other metal -cyanide complexes is presented and discussed. In addition, potential applications for the solvent extraction of gold from cyanide solutions are discussed.

Jan 1, 1983

By A. K. Sinha

A great potential market for the high BTU midwestern thermal coal exists if the coal is desulfurized and prepared to meet the environmental restrictions and the utility customer specifications. Because the midwestern coal is very high in pyritic sulfur, it can be adequately desulfurized by removing the pyrite with the help of such coal cleaning techniques as the froth flotation. Froth flotation cells are now commonly employed in modern coal preparation plants for recovering the fines but they are not utilized for desulfurizing the coal probably due to a lack of system operating data for such applications. A research project recently conducted at Southern Illinois University shows that the total sulfur in the midwestern coals can be successfully reduced from as high as 5.3 percent to less than 1.4 percent by single stage froth flotation. The results obtained on ten different samples of high sulfur coal obtained from different areas in the Illinois Basin are presented and discussed.

Jan 1, 1985

By A. B. Fly

This paper presents the equipment and techniques developed to mine subsurface mineral deposits through 16 inch bore holes entirely by hydraulic methods. Use of this equipment for excavating large cavities in oil and water well producing zones is discussed. Results of surface experiments using high pressure jet streams of water to determine the cutting rates of materials are outlined. Various basic shapes of subsurface excavations that can be mined with the equipment are illustrated and discussed. An example of the cost of mining by this method is presented. Problems encountered in the field operations led to the development of a new explosion type slurry pumping system and related slurry handling equipment.

Jan 1, 1969

By Charles B. Escapule

The first successful heap leach of silver ores in the State of Arizona has been under continuous operation since early 1976 at the State of Maine Mine, two miles southwest of Tombstone, Arizona. The silver produced from leaching old mine dumps at this property vas the first in the Tombstone mining district to achieve a 999+ purity. While cyanide leaching of silver and gold ores is a time-proven accepted practice, a relatively new method of treatment called "heap" leaching was employed. Heap leaching is a comparatively inexpensive fast way to recover precious metals from low grade material.

Jan 1, 1981

By John A. Rajala

The water chemistry of the froth flotation pulp is one of many parameters which can affect the flotation process. The fluid may contain certain inorganic salts which, along with increased ionic strength, can produce undesirable flotation depression or activation. A source of a salt could be the use of calcium chloride to prevent freezing in ore cars, chutes, and bins (Anon., 1980). Alternately, the salt or salts could be initially contained in the water as in the case of sea water and some brackish waters. These salts may become more concentrated because of the need for recycling of plant water due to environmental regulations and/or economic considerations (Davis, F.T., et. al., 1976). The presence of inorganic salts in flotation pulps and their effects upon the recoveries and surface chemistries of different oxide minerals have been the object of various studies. Some researchers (Fuerstenau, D. W. and Raghavan, 1976; Fuerstenau, D. W. and Modi, H. J. 1960; Kulkarni, R. D. and Somasundaran, P., 1977) have reported that addition of a salt can increase or decrease flotation recovery depending upon the particular system.

Jan 1, 1982

By William C. Grady

The environmental and economic problem created by pyrite in coal are well documented. The removal of pyritic sulfur prior to, or during, utilization has been the object of considerable research, however, much of this research has proceeded without a proper knowledge of the microscopic occurrences of pyrite in coal. This paper investigates the forms, occurrences, and variations in the distribution of pyrite in major West Virginia coal scan. Twenty-nine samples from twenty-two major west Virginia coal scans were selected for this study (see Table I). The samples were selected so as to be representative of the major coal producing areas of the state. All samples, except five, were collected at active surface mines, as indicated in Table I, and all except one were channel samples. The time interval between sampling and preparation of polished microblocks varied from two months to two years, though most were prepared within three months of collection. Grinding, screen¬ing, and riffling of samples to obtain 250 grams of -20 mesh coal for microscopic analysis strictly followed ASTM procedure D2013-72.

Jan 1, 1976

By Howard E. Kremers

Although more than 100 thorium-rare earth minerals are known, only a few have any commercial significance. Monazite, thorite, bastnasite, and some exotic thorium rare earth ores are reviewed Commercial interest is presently centered on monazite from the Union of South Africa, and thorite from this country. Thorium became commercially important with the development of the incandescent gas mantle about 75 years ago, Gas mantles consist of thorium oxide with small amounts of cerium oxide. The thorium nitrate used to make gas mantles was first obtained from rare thorium minerals, As a matter of fact, this use of thorium is still important and is one of the largest commercial uses for thorium materials. The discovery of monazite sand placer deposits along the coasts of Travancore, India, and in some Brazilian beach s .s, and the development of the old North and South Carolina monazite stream placers gave the mantle industry of 30 to 40 years ago a comfortable inventory of thorium ore. Even today, the thorium industry depends largely upon monazite ores for its source of thorium. This paper will briefly describe some of the major thorium ores and their principal deposits insofar as they relate to the thorium industry in this country. Because of similar chemical and physical properties, thorium always occurs with the rare earth elements and with varying amounts of yttrium. Thorium may predominate over rare earths, as in thorite-type minerals, or may represent only a fraction of the rare earth content. Typical ratios of thorium to rare earths in various minerals are given in Table 1, The average thorium content of the earth's crust is about 12 grams per ton, and in this respect thorium approximates lead, molybdenum, and some of the rare earths in abundance. The ore minerals of greatest importance to the-thorium-rare earth industry are monazite, thorite-type minerals, bastnasite-type- ores, and the family of minerals which is characterized by a preponderance of the heavy rare earths and yttrium. The latter classification includes xenotime, gadolinite, samarskite, euxenite, etc, The first two, monazite and thorite, are of greatest significance.

Jan 1, 1958

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

By Ralph B. Hall

Examination of cored material from the Southern Extension of the Florida Phosphate District has indicated a decidedly complex and diverse sequence of phosphatic sedimentary units. The perfunctory logging techniques formerly used in the Central District are inadequate to properly describe the intricate geology of these sediments. Adequate geologic training and familiarity with the potential ramifications of his judgement are a necessity for the logging geologist. A combination descriptive-graphic logging model is proposed that utilizes a standardized sediment nomenclature system and descriptive symbols for type materials commonly found in these sediments. Justification for adoption of this or a similar logging model is discussed.

Jan 1, 1983