Search Documents

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

2.1 INTRODUCTION When total extraction of an opening of sufficient size is reached in a horizontal coal seam, the roof strata in the overburden deform continuously to reach a new equilibrium condition. The severity of deformation decreases upward toward the surface. As the downward saggings of the strata propagate and reach the surface, there will be a depression zone on the surface directly above, but extending beyond the edges of the underground opening. This is the surface subsidence basin or surface subsidence trough. The surface subsidence basin is circular in plan view, if the coal seam is horizontal and the mined-out opening is square in shape. But it is rectangular with rounded corners or elliptical if the coal seam is horizontal and the mined-out opening is a long- and thin rectangle or a short-rectangular, respectively (Fig. 2.1). Most underground openings (e.g., longwall panel) assume rectangular shape when total extraction has been completed. Theoretically the edges of the subsidence basin are the points of zero subsidence. But it is difficult to exactly locate the points of zero subsidence. Therefore in practice the points with vertical subsidence of 0.4 in. (10 mm) are used. The final subsidence basin is that which exists long after the mining has been completed, because its magnitude and shape are quite different from the dynamic subsidence basin formed while the face is moving. 2.2 CHARACTERISTICS AND TYPES OF DEFORMATION IN THE FINAL SUBSIDENCE BASIN For a horizontal coal seam, every point in the subsidence basin moves toward the center of the basin. Subsidence is maximum at the center of the basin. Any cross-section that passes through the point of maximum subsidence and either parallel to AB or CD line (Fig. 2.1) is a major cross-section along which principal directions of surface movements occur. However among those infinite numbers of major cross-sections, two specific ones are of special significance, not only because the magnitudes of surface movements are the largest, but also because they are the most easily identifiable directions, i.e., one that is parallel to the faceline at the center of the basin (CD in Fig. 2.1) and' the other is that perpendicular to the faceline but parallel to the diction of face advance (AB in Fig. 2.1). Nearly all the subsidence data obtained in the US have been derived from these two cross-sections, although some cross- sections parallel to CD but near the edges of the panel have also been included. In addition to moving horizontally toward the center of the basin, every point in the basin also subsides vertically. The magnitude of subsidence increases toward the center of the basin. Therefore surface subsidence is a three-dimensional problem and should be treated so in all cases. On all the major cross-sections, only principal subsidence and principal displacement occur. Since subsidence and displacement vary continuously in every major cross-section, three additional deformation components are de- rived, i.e., slope, curvature, and strain. On all other non-major cross-sections on the other hand the five components are accompanied by two additional components, i.e., twisting and shear strain. The seven components of the surface movement are defined as follows (Fig. 2.2): 1. Subsidence, S. On any cross-section, the vertical component of the surface movement vector is called surface subsidence. It generally points downward. But sometimes it points upward in areas ahead of the faceline or beyond the edges of the opening. In such cases it is a surface heave which is usually less than 6 in. 2. Displacement, U. On any cross-section, the horizontal component of the surface movement vector is called surface horizontal displacement. It generally points toward the center of the subsidence basin. But in steep terrain, it moves along the downdip direction 3. Slope, i. On any cross-section, the difference in surface subsidence between the two end points of a line section divided by the horizontal distance between the two points is called the surface slope of the section. 4. Curvature, K. On any cross-section, the difference in surface slope between two adjacent line sections divided by the average length of the two line sections is called the surface curvature of those two line sections. There are two types of curvature: con- vex or positive curvature and concave or negative curvature. 5. Horizontal strain, e. On any cross-section, the difference in horizontal displacement between any two points divided by the distance between the two points is called horizontal strain. If the distance between the two points is lengthening, it is tensile strain with positive sign. Conversely, if it is shortening, it is compressive strain with negative sign 6. Twisting, T. On the surface of the subsidence basin, the difference in slope between two parallel line sections divided by the distance between the two line sections is called twisting. 7. Shear strain, y. Shear strain is the changes in internal angles of a square on the surface of the subsidence basin or on any major cross-section. It is the summation of the differences in incremental (or decremental) lengths between the two opposite sides divided by the original distance between the two opposite sides. More precisely, the surface deformation indices (i.e., slope, strain, curvature, twisting and shear) are defined by derivatives of surface movement components. For simplicity, the x- and y-axes of the cartesian coordinate system are set to be parallel and perpendicular to the cross-section of interest, respectively. In such a coordinate system, slope and curvature along x direction are the first and the second derivatives of the vertical components (S) of surface movement with respect to x, respectively, or i, = ds/dx and kx = d2s/dx2. Horizontal strain along x direction is the first derivative of the component along x direction of the horizontal displacement,

Jan 1, 1992

By Edmund W. Murphy

At the first workshop on Surface Subsidence Due to Underground Mining (1 981 ) , Yarbrough delivered a paper (1 ) describing the mine subsidence insurance program in Illinois operated as the Illinois Mine Subsidence Insurance Fund (IMSIF) . In this paper we will present claims data and describe changes that have occurred in the Illinois Insurance Code during the first six years the IMSIF has been in existence. The change in the original Illinois Public Act 80-1 41 3 that most affected the public was an amendment increasing the maximum amount of mine subsidence insurance avail- able on a structure from $50,000 to $100,000. Seventy-two counties in Illinois have been undermined for minerals, primarily bituminous coal. In Franklin County (.in the southern part of the state) 36 percent of the land area has been undermined for coal extraction. In St. Clair and Madison Counties , two counties that include the St. Louis Metropolitan area along the western border of the state, 10 percent and 7 percent of the land surface have been undermined. Most of the undermined area in the two counties is beneath urbanized land. In 34 counties, approximately 1 percent or more of the land surface has been undermined (2). The first shaft mine in Illinois was sunk in the city of Belleville (east of St. Louis) in 1842, and the mines of early vintage have initiated the majority of the mine subsidence claims. Data compiled from the first six years reveals that most Illinois mine subsidence events that affect structures occur over abandoned mines where early methods of high- extraction mining practices were used. Maps of these mines operated in the 1800s reveal irregular development of room and pillar areas and poorly defined production areas (panels). Rooms in the mines varied from 15 to 40 feet in width and the pillars varied in width from 5 to 40 feet. The pillars were often long and narrow. Recovery rates in mines that operated prior to 1900 generally averaged 50 per- cent, and extraction rates as high as 80 percent have been documented (2). Some pillar robbing occurred.

Jan 1, 1986

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By Eddie Woods, Jon Hurt, Roger May, Paul Watson

The Channel Tunnel Rail Link (CTRL) will be Britain’s first major new railway for over a century—a high-speed line running for 109km (68 miles) between St. Pancras station in London and the Channel Tunnel. The new line has been under construction since October 1998 and the first phase will open in October 2003. The project includes22km of twin 7.15m ID TBM bored tunnels under London and the River Thames, and the 3km North Downs Tunnel, the first major NATM tunnel to be constructed in the United Kingdom since the collapse of the Heathrow Express Tunnels in 1994. This paper will discuss the design of these tunnels and describe the construction progress to date. The discussion will include details of segmental lining design, TBM specification, and sprayed concrete lining design.

Jan 1, 2003

By Charles Kimbell, L. Nahai, E. Shekarchi

INTRODUCTION AND SUMMARY World mineral trade during 1960 to 1984 has shown substantial changes both in value and tonnage. Although fuel commodities dominated total mineral trade during this period, this paper will focus attention primarily on nonfuel minerals. Brazil and Australia, modest producers of iron ore in 1960, have become dominant producers and exporters, together accounting for about half of major iron ore exports in 1984, far surpassing traditional export suppliers such as Sweden. Australia has also become the largest producer and trader of bauxite and alumina, and worldwide alumina trade has increased at the expense of bauxite trade. Similarly, shipments of ferroalloys have increased more than shipments of ores such as those of chromium and manganese. Canada, retaining its first rank in world export of zinc, has become also the leading source of potash and sulfur in world trade, and South Africa has been the dominant factor in chromite, manganese and their respective ferroalloys. Developing countries' share of world copper trade has increased, with Chile maintaining first rank, but developed industrialized countries have continued to dominate production and trade of lead and zinc. Phosphate, sulfur, and potash have been the principal crude nonmetallic minerals traded worldwide. Looking to the near future, dramatic increases in export of iron ore, phosphate, potash and sulfur are not envisaged. Bauxite exports will continue to decline relative to alumina but at a slower rate than in the recent past. Zinc concentrate will continue to be exported but lead will be traded more as metal than as concentrate. For iron and steel, there will be some production shift from traditional producers to certain developing countries and recently industrializing developing countries such as Brazil, India, the Republic of Korea, and Taiwan. In the following sections dealing with specific commodities, it should be understood that information is presented only on the major forms of each commodity that move in trade, and only for a selected group of countries for each commodity or major form of each commodity. Thus, totals shown or mentioned generally represent only the totals of figures presented here and do not include estimates for minor forms of material or for countries that are not listed. However, the data provided is regarded as sufficiently complete to reflect major patterns and trends, and exclusions are there- fore not seen as affecting conclusions that may be drawn from the material provided. FUEL AND NONFUEL TRADE Values of Fuel and Nonfuel Trade The value of world export trade in major mineral commodities (ores, concentrates and scrap, crude minerals, iron and steel, nonferrous metals, nonmetallic minerals and mineral fuels) in 1983, the latest year for which comprehensive data are available, was reported by the United Nations in May 1985 to have totaled over 514 billion current U.S. dollars (Table 1). This was 79% of the historic record high of nearly $649 billion ,current dollars set in 1980, but almost 18 times the current dollar value reported for 1960. [1/] The value of these 1983 exports in constant 1960 dollars was $164 billion (Table 2), only 66% of the record 1980 high of almost $250 billion, and only about 5.7 times the 1960 dollar level.

Jan 1, 1986

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress' To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder's method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By S. Horton, F. L. Stanley, P. J. Bethell

Introduction The McClure River Processing Plant is located at McClure in Dickenson County, VA. The plant was originally constructed in 1979 as a 600 st per hour facility. The plant is fed by coals from numerous mines in the area as well as a major longwall mine onsite. Coal is processed predominantly for the metallurgical coal market. The original plant was comprised of three separate processing circuits incorporating a heavy medium vessel for the coarse material (+10 mm). Intermediate sized material (10 x 0.6 mm) was beneficiated in heavy medium cyclones, with the remaining fines (0.6 mm x 0) passing to froth flotation for upgrading. The products from all three circuits were combined prior to thermal drying and then stored in silos or ground storage prior to shipment to the metallurgical coal markets. A middlings heavy medium cyclone circuit was also present to rewash the vessel and primary heavy medium cyclone rejects. The original circuit is as shown as Fig. 1 (Editor's note: All figures are reproduced at the end of this paper.) In reasonably close proximity to the McClure Plant is the much older, less efficient Moss 1 Plant, (Chance cone, table, water only cyclone, froth flotation, Fig. 2), which prior to the McClure Plant expansion was processing considerable tonnages of coal. At that time, the McClure River Plant was processing coal at the maximum possible feed rate, and the Moss 1 Plant was finding increasing difficulty in maintaining the stringent quality specifications on its major metallurgical coal accounts. Given the fact that many of the feeder coals to Moss 1 could be moved with minimal difficulty and cost to McClure, an exercise was conducted to evaluate the potential of expanding the McClure Plant. This would result in transferring coals from Moss 1, thereby increasing yield, reducing operating costs, and enabling customer specifications to be met more easily. After evaluating many possible ways of expanding the McClure Plant, we eventually settled on an approach based on the idea of Gallagher at German Creek in Australia (Gallagher, 1986). Our objective was to increase plant capacity by removing the coarser size fractions (0.60 x 0.15 mm) from froth flotation and at the same time eliminating the finer fractions (1.25 x 0.6 mm) from the heavy medium cyclone circuit, thereby allowing these circuits and therefore the plant as a whole to increase its capacity. These size fractions (0.60 x 0.15 mm from froth flotation and 1.25 x 0.6 mm from the heavy medium cyclone circuit) would be treated in a new spiral circuit. After desired evaluation of the various circuit capacities, including desliming screen, clean coal filter and thermal dryer capacities, etc., it was concluded that we should be able to maintain high levels of processing efficiency in the existing circuitry while at the same time expanding plant feed rate from a nominal 600 st per hour to 1000 st per hour, thereby achieving the objectives The circuit that was finally settled on is shown in Fig. 2. Several unique features were incorporated in this circuit in an attempt to maximize processing efficiency and reduce maintenance costs. First, the idea of a single-stage spiral circuit was abandoned in favor of a two-stage circuit incorporating rewashing the primary spiral middlings in a secondary spiral (Bethell, 88). The spirals selected were Mineral Deposits Model LD4 units. It was felt, after much previous testing, that spiral middlings rather than being a true middling gravity fraction were in fact a combination of true middlings with a preponderance of misplaced light coal and high-density rock. Consequently the insertion of this material directly into either clean coal or refuse streams (per normal practice) would only lead to loss of efficiency. The operating philosophy behind the design of the circuit was to produce the purest coal and rejects possible by adjusting the spiral splitters. Misplacement of refuse into the clean coal and vice versa would be minimized by taking a fairly large middlings cut. By reprocessing this material (10%-15% of primary spiral feed) in a secondary bank of spirals the misplaced material in the primary middlings would be reprocessed and its probability of reporting to the correct stream greatly enhanced. To minimize fines loading on the spirals, fine aperture sieve bends were to be included. A further novel feature of the circuitry is the desliming/ dewatering system. A philosophy of accepting inefficiency but forcing it to work in our favor was developed. The dewatering screens (Linatex Combis) were chosen not for their ultimate screening efficiency but for their ability to remove slimes (tolerating a fair quantity of oversize in the effluent) and their enhanced maintenance characteristics. Any oversize passing into the effluent, together with the fine coal centrifuge effluent, would pass to classifying cyclones, the objective of which was to reject to overflow (and hence froth flotation) as many fines as possible (-150 µm) without running the risk of losing coarse (1.25 x 0.15 mm) material to oversize. Hence, by a process of producing a "slime free" screen product coupled with a "coarse free" cyclone overflow, sizing efficiency could be maximized. Obviously, recirculating load had to be factored into the Combi Screen design capacity. The spiral circuit as shown in Fig. 2 was installed at McClure River in January 1988. The spiral circuit efficiency was very high immediately, and, after the normal debugging, plant capacity has been increased to the point at which we are currently processing of the order of 1100 st per hour. Test program The performance of the spiral circuit has been evaluated by two major samplings of the entire new circuit, coupled with routine bi-monthly tests on all other major components of the plant circuitry.

Jan 1, 1992

By Robert C. Freas

Lime, the versatile chemical is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is made from high calcium or high magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high calcium lime has less than 5% MgO. When the lime is produced from a high magnesium limestone, the product is referred to as dolomitic lime. Calcination/Hydration Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 AD. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from scientific perspective. The pro- duction of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 25 to 30 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Particular emphasis has been focused upon energy consumption and fuel efficiency. Calcination refers to a broad class of reactions, of which the limeflimestone reaction is just one, wherein a substance is heated to less than its melting point, resulting is a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [ ] While there is nearly universal agreement bout the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in [Fig. 1]. From this model it can be seen that calcination is a function of both temperature and CO, pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the interface must make its way through the lime to the exterior surface. Since calcination is limited by gas diffusion to the surface of the partially calcined limestone, the natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in calcination rate. Therefore, the suitability of a given limestone as a source material for lime production can be determined only after completion of adequate burn tests designed to evaluate the various limiting factors. When a coal-fired kiln system is considered, the entire process of calcination is made even more complex by the introduction of additional chemical constituents into the calcination environment. The reader is referred to the references for a more detailed description of the complete calcination reaction and the differences inherent between differing kiln systems. In the foregoing discussion it was noted that CO2 is released during the reaction. This release results in a 44% weight loss during the complete calcination of a high calcium limestone, or a 48% weight loss for a highly dolomitic limestone. The trade term for this weight percent loss is loss on ignition, or LOI. This weight loss is frequently used as a measure of the completeness of calcination. Because the calcination reaction is chemically reversible, quicklime or burned lime is frequently referred to a being highly reactive, or unstable. The more stable form of lime, hydrated lime, is commonly preferred and generally specified by the user. Hydrated lime is obtained by adding water to quicklime to produce a dry, fine powder. Quicklime's affinity for moisture is then satisfied, although it still retains a strong affinity for CO2.

Jan 1, 1994

By B. Jones, W. Zhang, Q. Li

Rare earth elements (REEs) are critical materials to the United States due to the imbalance between their supply and demand. Considerable research and development efforts have been devoted on REE recovery from coal refuse using inorganic acids as lixiviants, however, the cost of inorganic acids is normally high, and the environmental friendliness is low. As alternatives to inorganic acids, organic acids of small molecules such as lactic acid and succinic acid have been used as efficient and green lixiviants for metal extraction. In addition to the supply risk of REEs, food waste generation and disposal is another emerging and critical issue since nearly one-third of the edible food is lost or wasted each year. In this research, organic acids were microbially converted from food waste and used as lixiviants to leach REEs from density fractions of an Illinois Basin coal. Experimental results indicate that REE recovery increases of up to 15 absolute percentage points were obtained using organic acids relative to inorganic acids. The conversion of food waste into value-added, renewable, and environment-friendly chemicals promotes the economic viability of REE recovery from coal refuse.

Mar 2, 2022

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By David A. Greenhut

The Kubota surface melting system has been under development since 1975. It has found commercial application on the melting of municipal sludge, and ash from solid waste. The melted product has physical properties allowing its use as a substitute for aggregate in cement and asphaltic construction. This paper describes the surface melting system, its current use and anticipated future use.

Jan 1, 1991

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By D. W. H. Su

"This paper presents the results of a comprehensive study conducted by CONSOL Energy, Marcellus Shale Coalition, and Pennsylvania Coal Association to evaluate the effects of longwall-induced subsurface deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall abutment pillar can maintain mechanical integrity during and after mining operations. A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar were mined by. To evaluate the resulting coal protection casing profile and lateral displacement, three separate 60-arm caliper surveys were conducted. Prior to the longwall panels being mined by, a number of 3D finite element simulations were conducted to estimate subsidence at the surface, coal pillar pressure increases, the resulting coal protection casing profile and displacement, and the vertical and horizontal displacements in the four monitoring wells. Comparisons of the pre-mining 3D finite element simulation results and the surface/subsurface/underground instrumentation results show that the measured test well and IPI casing deformations and profiles are in reasonable agreement with those predicted by the 3D finite element models, and that the measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models, which serves to validate the 3D finite element models. Parametric studies employing the validated 3D finite element models demonstrate that larger coal protection casing thickness is expected to have little effect on the lateral deformation, although it may reduce the magnitude of casing plastic deformation, and under deeper cover (~1,100 feet), lateral casing deformation is expected to be smaller, although larger plastic casing deformation may be present near the seam level. Also, evaluation of various casing and cementing designs using the validated 3D models clearly indicates that, when all casings are grouted to the surface except the intermediate and production casings, the intermediate and production casings show little deformation and no plastic strain. This research represents a very important step and initiative to utilize the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the oil and gas industries"

Jan 1, 2017

By John G. Groppo, Bonnie Webb-Groppo

INTRODUCTION The first portion of this chapter is concerned primarily with the contamination aspects of fine coal cleaning that include both the solids and water discharged as waste products after coal preparation. Topics include characteristics of the water and solids, changes that occur to both of these phases during use and after impoundment, as well as the impact that these changes have on unit operations and the environment. Attention is also given to the formation of acid mine drainage and treatment options that may facilitate reuse of the water. The second part of the chapter analyzes the problem of air contaminants from coal preparation plants including analysis of air pollutants and control methods. An overview of air quality regulations is also presented; most provisions have little or no applicability to coal preparation plant operation but are presented to provide an understanding of end-user constraints. The final part of the chapter emphasizes the long-range problem of refuse disposal and control. An overview of characterization, maintenance, and control of the refuse area is presented, as well as design guidelines. A brief review of stability analysis procedures is also included. PREPARATION PLANT WATER Characteristics of Makeup Water for Coal Preparation There are few specific rules governing the quality of makeup water used in coal preparation processes.'" It is generally accepted, however, that the solid matter content should be less than 5%. The solids concentration in plant makeup water typically varies between 0.25 to 0.9 lb per gal (30 to 110 g/L) and may reach concentrations as high as 1.7 lb per gal (200 g/L). The water used in coal preparation is usually obtained from one or more of the following sources: public supplies, rivers and streams, canals, mine water, and wells. In most cases, water is obtained at the lowest cost including any necessary treatment. A major portion of the recirculated water is clarified by thickeners and settling ponds to remove fine coal and clay particles. Sufficient water is generally available to meet the needs of coal preparation in most areas. It has been estimated that approximately 65 to 70% of the makeup water used in a coal preparation plant comes from surface sources. It is important to note that a variety of substances are commonly found in natural water supplies, whatever the available source may be (Table 11-1). Excessive concentrations of some of those substances can have an affect on plant performance; the effect of specific contaminants on unit operations will be discussed

Jan 1, 1991

In spite of the tremendous amount of research conducted in the last few decades. no single blasting theory has been developed and accepted that adequately explains the mechanisms of rock breakage in all blasting conditions and material types. Given specific test environments, conditions and assumptions, individual researchers have contributed valuable information and insight as inputs into blasting theories, although a simple "plug-in" type formula for predicting optimum fragmentation, muck pile geometry and casting distance, is still largely unresolved. There is as yet, no consistent and widely applicable theory of blasting, but only a number of limited and disconnected theories; many of which are empirical in nature and based on ideal blasting conditions. Blasting theories have been formulated and based on pure speculation, years of blasting experience on a trial-and-error approach, laboratory testing, field investigation, and mathematical and physical models adapted from other disciplines of science.

Jan 1, 1988