Search Documents

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By C. D. Secrest

Visiting Spring Canyon, a historic coal mining district near Helper, Utah, I was impressed by the great accomplishments that had taken place there. A tour book of the region tells of a period that began in the early 1900's, when the land was still very much the Old West, when settlers lived out their lives in coal company towns and produced a resource that was to build a nation (Cunningham, F., 1990). Between 1912 and the early 1970's, 11 mines had come and gone in that narrow canyon less than 15 kilometers long. Spring Canyon is a historic district now, but I could not dwell too long on the richness of its history. I was there to look for evidence of PCBs.

Jan 1, 1993

By Anna Sieminska-Lewandowska, Monika Mitew-Czajewska

"The construction of 6.3 km long central part of 2nd metro line in Warsaw was completed in September 2014 (7 stations - out of which three 25m deep stations - built using cut and cover method; two single-track tunnels constructed using four EPB TBMs as well as a short NATM section with soil freezing below the existing road tunnel). Central section of the 2nd metro line was opened to public after verification and testing in March 2015. Design and build tender for the extension of this line in East (three stations) and West direction (three stations) was announced with total length of running tunnels – approx. 5 km. Detailed description of a very complex geotechnical context, different construction methods, challenges encountered and solved during construction and finally lessons learnt on this interesting project are presented in the paper. DESCRITPTION OF THE PROJECT Introduction The very first concept plan of the metro system in Warsaw was designed several years after regaining independence by Poland in 1918. In 1929, following the geotechnical survey, design works begun, but the economic crisis of the 1930s stopped it. After a few years of break, in 1938 a coherent concept of the metro network was proposed to be implemented in phases over the next 35 years. In total, construction of 46 kilometers of metro, including 31 km of tunnels and 15 km on surface, was planned. Unfortunately, World War 2 made the implementation of those plans impossible. In the post-war period several metro designs were elaborated, but none except one was scheduled for implementation. Construction of the 1st, 23.1 km long, North-South line commenced in 1983 and finished in 2008 (Sieminska-Lewandowska et all. 2009). Nowadays, Warsaw covers the area of 517 km2 and, according to year 2014 statistical data, the city has much more than 1.7 million inhabitants. Only one operating metro line is not sufficient for such a populated city. Up-to-date metro plan, shown on Figure 1, includes also 30.5 km long 2nd metro line. It’s route is divided into four sections: Western Section with the length of approx. 9.2 km and 9 stations, Central Section with the length of 6.3 km and 7 stations, North-East Section with the length of 7.7 km and 6 stations, South-East Section with the length of 7.1 km and 6 stations. The construction of the central part of the 2nd metro line in Warsaw was completed in September 2014 and its operation started in March 2015. The paper focuses on challenges encountered and solved and lessons learnt during construction of the central part of the 2nd metro line in Warsaw."

Jan 1, 2016

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

By E. Forssberg

Studies have been carried out with the High Pressure Roller Mill, HPRM, to produce calcium carbonate minus 10 micron. This paper presents the optimization of the specific grinding force of the HPRM system for a maximum energy utilization when limestone is ground. In addition, experimental tests of producing carbonate minerals using the HPRM as a pre-crusher are described in this paper.

Jan 1, 1996

By H. H. Murray

Industrial usage of clays for current and new applications will continue to grow into the next century. The rate of growth will be highest in the less developed areas of the world. Transportation costs are a significant part of the delivered price, so the location of reserves and processing facilities for kaolin, bentonite, and palygorskite (attapulgite) are reviewed relative to serving these emerging markets. New value added applications will increase in the more developed areas which will require high quality raw materials, more sophisticated processing, and rigorous quality control.

Jan 1, 1998

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By Edgar F. Cruft

It is sometimes said that "mines are made, and not found". I rather doubt that the exploration geologist would be overly sympathetic to that statement, and, of course, like most one-liners it is only partly true. As an explorationist who has been involved in building his own company over the last ten years, and by necessity has become a financier, I can appreciate what real grains of truth are in that statement, however. Because technical people are seldom taught financing in their basic training, and because they are usually not involved in it until at quite a senior level in their careers, the whole field often acquires a certain mystique. The engineering professions have too often believed financing is the province of the accountant or financial executive and just as we in the technical world are often too quick to bristle if the latter try to tread on our domain, the opposite can just as easily be true. Unfortunately, this is another example of a compartmentalized individual, and that is one thing the successful financier cannot be.

Jan 1, 1979

By Stephen R. Hunt

This paper summarizes some preliminary results of the Illinois State Geological Surveys current investigation into surface subsidence resulting from coal mining in Illinois. The purpose of the study is to characterize-the vertical movements that may result from various types of underground coal mining. In general there is relatively little published information about subsidence from room-and-pillar mining as compared with longwall mining. The findings of this study, based on mining operations in a variety of geologic settings, delineate the magnitude, shape, and position of the subsidence profile. Comparisons of case histories of subsidence are based primarily on the extraction ratio and the general geometry of the mine (depth, panel width, and mining height).

Jan 1, 1979

By A. Bruynesteyn

Many papers 'have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By Raymond A. Bradbury

Martin County Coal Corporation operates three underground mines and two surface mines on Wolf Creek in Martin County near Inez, Ky. The original underground development was begun in March of 1970. The property being developed is leased from Pocahontas Land Corporation. The A. T. Massey Coal Company, whose offices are located in Richmond, Virginia, is the parent company and sales agent for Martin County Coal. Duke Power Company is the customer who will take all the production from the mines which ultimately are scheduled to produce 2,500,000 tons annually. The Norfolk and Western Railway Company built a 24-mile railroad into this huge reserve of low-sulfur steam coal. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton seams are being deep-mined now and it is in three mines that the diesel haulage equipment is used. Those of you who attended the AIME meeting in Birmingham last October or the Diesel Symposium in Pittsburgh in January of this year are familiar with the introduction of trackless diesel-powered haulage equipment into our Martin County mines. I made a presentation at each of those meetings which dealt with our first experience with Wagner Mining Equipment haulage units. These machines are sold exclusively by Lake Shore, Inc. whose offices are in Iron Mountain, Michigan.

Jan 1, 1973

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By Jesse H. Auvil

In January of 1966, during the annual session of Georgia's General Assembly, Representative Paul E. Nessmith of Statesboro, Georgia, walked into my office and asked me what I thought of the advisability and feasibility of a law which would require the mining operators to reclaim their mined out lands. My answer to him was, as a one time mine superintendent and operator, that I probably would not think very highly of the added cost which reclamation would impose on the operation; but that since assuming the job of Chief Geologist and Assistant Director of the Georgia Department of Mines, Mining and Geology, and in retrospect, I could recommend it very highly, particularly in view of the increased pressure being applied by the Federal government along these lines. I stated then and still emphatically state that this sort of administration should be done on the State level rather than the Federal level. He asked me if I would conduct him on a tour through some of the mining country in which I had worked and to this I readily agreed. The result of this trip was that he was adversely impressed by the devastation which the mining operations had wreaked on that area of middle Georgia along the fall line known as the kaolin belt. Very little except talk was done for the remainder of 1966.

Jan 1, 1970

By Alissa Lockett, Chris D. Breeds

Central Water Integration Project (CWIP) Segment 5-1 is the most critical segment of a regional water supply project that transfers groundwater from Burleson County to northern San Antonio, replacing over 20% of that City’s water supply with a new source. CWIP Segment 5-1 included three tunnel reaches totaling 10,350-ft and 5 shafts that were constructed inside the City in an area known to contain large karst features. This paper describes site work used to investigate the alignment for karst features, manage potential environmental impacts, develop the contract package required for mitigation and the means and methods used to mitigate the large karst features that were encountered.

Dec 1, 2022

By D. A. Bird

Water chemistry data were used to identify the sources of ground-water and surface-water inflow to the IOZ block cave mine. Water samples were collected to obtain vertical and lateral hydrochemical profiles within different levels of the underground workings. Water chemistry data were evaluated in conjunction with geologic and structural information to define controls on locations of ground-water inflows, and to select targets for drilling and interception of water. Drilling has intercepted water-producing zones that were previously unidentified through mapping and drilling. The program has resulted in a reduction in water inflows to the block cave area.

Jan 1, 1998

By E. Watkins, R. Kimutis, H. Dougherty

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry and can assist with a well breach scenario. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Mar 2, 2022

By Lawrence M. Brennan

Early in 1971 the Peabody Design and Preparation group began engineering on a preparation plant which was to process eight mil- lion tons per year of raw coal. For the first five or six years this product was to be furnished 50% from surface mining operations and roughly 50% from underground operations. By early 1980, 1008 of the production was to come from underground mines. Because of the large annual commitment from Randolph Preparation Plant, it was essential that the plant operate with minimum down-time. As usual, capital costs were to be kept at a minimum. Before we discuss the details of design, it would be best to discuss the overall picture. Underground production to be pro- cessed through Randolph Preparation Plant was to be delivered by means of one mile overland conveyor from Baldwin #1 Underground Mine to the plant. Surface Mine production was to be delivered by means of 100-ton haulage units dumping in a 1,000-ton capacity hopper. Because of the changing production rates in both the underground and surface mines as well as the great difference in size consist, it was decided that it would be necessary to divorce the plant as much as possible from production. For this reason, twin 6,500-ton raw coal silos were constructed to separate the two coals as well as allow blending. The preparation plant itself, was to be designed to Operate two shifts per day, five days per week, at an average rate Of 2,200 tons per hour with a maximum rate of 2600 to 2800 tons per hour. Coal was to be delivered to our customers by means of rail haulage at both unit train rates and plant process rates. The surface mined coal, after discharging into the 1,000-ton R.O.M. hopper, is fed by means of two 72" wide reciprocating feeders onto a 72" wide steel cable belt. The steel cabled conveyor discharges the R.O.M. coal onto a fixed grizzly, scalping out a percent of the 6 x 0 coal. The balance is fed to a 12' x 27' Rotary Breaker. The material passing through 6" round hole screens is added to the 6" x 0" from the scalping screen. The 6" x 0" is conveyed to the top of one of the 6500 ton silos designated for surface coal. Material that is not broken to pass the 6" breaker screen is discharged to a bin and disposed of with plant refuse.

Jan 1, 1976

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964