Search Documents

By F. Calizaya, S. Bhattacharyya

"INTRODUCTION Mechanized underground mines often suffer from noise overexposure. Noise levels are usually above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach 121 dB(A), especially when fans are not equipped with silencers. Use of silencers seldom ensure PEL for various reasons. Overexposure of noise induces permanent hearing loss among mine workers. Recent field studies by a NIOSH-funded research project at six coal and non-coal mines revalidated the findings. The University of Utah has undertaken laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material has been designed and tested. The silencer and an associated extension which can be repacked with different dampening materials were used in various configurations. Attempts were made to simulate field conditions where installations are quick and not perfect. The test results are presented here. NOISE IN UNDERGROUND MINES Noise induced hearing loss (NIHL) is a chronic problem in the mining industry. In spite of regulations being in place and elaborate hearing protection programs under way, hearing loss is prevalent among the mine workers (Bise, 2001). All production and support machinery in mining generate loud noise often beyond the approved exposure level. Researchers in the U.S. have identified auxiliary fans as one of the major sources of noise that can create noise exposure levels up to 121 dB(A), which is one of the highest in the mining operation (Bauer, 2006). Studies have demonstrated substantial reduction of noise level by using silencers. Adequate fan selection and proper utilization of silencers in auxiliary fans have great potential of abating the problem. In hard rock mines, auxiliary fans are used in blower configuration to ventilate development headings and large production stopes, and also to ventilate underground shops, crushers, conveyor transfer points, etc. Typical duct diameters in hard rock mines vary from 0.91 m to 1.21 m. Silencers are often omitted for cost reduction. In coal mines auxiliary fans are used in exhaust configuration with rigid ducts 0.61- 0.76 m in diameter (Hagood, 1982 and Moreby, 2009) to ventilate working faces in gate-roads and main entry developments. Sometimes, stone dusters are added at the discharge end to dust the roof, ribs and floor. AUXILIARY FANS AND SILENCERS Auxiliary fans are relatively smaller in size than the main fans and often have high rotational speeds (1800 -3000 rpm). Fans are selected based on pressure-quantity requirements and space restrictions only. Noise emissions are rarely considered during the selection stage. Installation of fans, ducts and other accessories is mainly based on best practices, which often do not include noise control. As a result, the operation of an auxiliary or local ventilation system normally produces excessive noise."

Jan 1, 2018

By F. Romero, L. Yacher, M. Orchard

Specific software tools for Statistical Multivariate Analysis combined with real time process data were applied to Concentrator Plant at Compañía Minera Doña Inés de Collahuasi SCM in Chile, basically to two Mill Lines, each one with one SAG mill (32’x15’8MW)and one Ball mill (22’x36’9.7MW). The main objective was to empower the operator actions using process patterns references instead of process variable set-points. Pattern clustering and the analysis of pattern deviations regarding normal or desired pattern, allows for improvements in process control and the further implementation of soft sensors for those variables not included in the initial model.

Jan 1, 2003

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

By Hans G. Machel

In low-temperature diagenetic environments (0 c T c 60 - 80°C), elemental sulfur forms by six common processes: via (1) inorganic oxidation of H2S by molecular oxygen, (2) inorganic oxidation of H2S by ferric iron compounds, (3) polysulfide disproportion- ation; and via the microbial metabolic actions of (4) colorless sulfur bacteria, (5) colored sulfur bacteria, and (6) some types of thiobacilli. Economically viable deposits of native sulfur usually are formed by only one process: inorganic oxidation of H2S by molecular oxygen. The amount of elemental sulfur is also limited by three common processes that destroy it in low- temperature diagenetic environments: bacterial reduction, bacterial oxidation, and inorganic oxidation. In high-temperature diagenetic environments (80 - 10o°C c T c 150 - 200°C), particularly in sour gas reservoirs, there are seven common processes forming elemental sulfur: (1) SOdH2S reaction, (2) H2S- hydrocarbon reaction, (3) polysulfide disproportionation, (4) catalytic H2S decomposition, (5) C02-H2S reaction, (6) chlorinification, and (7) exsolution of physically dissolved elemental sulfur. Natural processes that destroy or remove elemental sulfur in such settings are hydrocarbon sulfurization, polysulfide formation, and advection. In most sour gas reservoirs, relatively small quantities of elemental sulfur occur as a free phase (solid or liquid). However, elemental sulfur often precipitates in copious amounts from the reservoir fluids via exsolution and polysulfide disproportionation during production of sour gas reservoirs. By extension, elemental sulfur may precipitate from reservoir fluids in relatively large quantities upon uplift and erosion of deep sour gas reservoirs, or from advection of sulfurous fluids into shallower settings via faults or other high-permeability pathways.

Jan 1, 1992

By William G. Doepken

GENERAL DESCRIPTION The Henderson mine utilizes a highly mechanized, continuous panel-caving system to extract ore from a deep, massive, molybdenum deposit. The mine site, lo¬cated 80.5 km (50 miles) west of Denver, is situated at 3170 m (10,400 ft) above sea level in a steep valley on the eastern side of the Continental Divide. The mill site, located on the western side of the divide, is linked to the mine via a 15.5-km (9.6-mile) railroad tunnel. Mine production is scheduled to reach 27 215 t/ d (30,000 stpd) from the uppermost production level. This pro¬duction rate will have been reached within the four years following an intensive ten-year preproduction development program. A second production level, due to come on stream in later years, will expand production capabilities to 31 751 t/d (35,000 stpd). The mine, which employs approximately 2000, has blocked-out ore reserves of 220 Mt (242 million st) at an average grade of 0.42% MoS2. Geology The Henderson deposit is composed of two partially overlapping ore bodies that lie 1080 m (3600 ft) beneath the peak of Red Mountain. The ore bodies are entirely within a Tertiary rhyolite porphyry intrusive complex that has intruded Precambrian granite. The de¬posit is elliptical in plan with overall dimensions of 670 x 910 m (2200 x 3000 ft). In section it is arcuate with an average thickness of 185 m (600 ft). The top of the deposit is at an elevation of 2610 m (8700 ft) while the lower limits range from 2340 m (7800 ft) on the west to below 2100 m (7000 ft) on the east. The mineralization is relatively continuous in the ore bodies and consists of molybdenite and quartz in random to subrandom, intersecting, closely spaced veinlets. Cavability RQD (rock quality designation) * values measured from Henderson drill core and compared with the RQD values from the Climax and Urad block-cave mines in¬dicated that the Henderson ore would cave but with difficulty and that a high percentage of the cave ma¬terial would be blocky. Initial caving experience shows the Henderson ore caves easier and with greater frag¬mentation than was indicated by the RQD values. Pos¬sible reasons for this are: 1) The greater lithostatic load at the Henderson has a greater effect on caving and fragmentation than anticipated. 2) The relief of confining pressure due to caving action and brittleness of the rock is enhancing breakage. Mine Layout The Henderson mine layout was designed from its inception for a large-scale, rubber-tired, continuous panel-caving mining system. The ore body is vertically divided into three major mine levels (Fig. 1). The top¬most level (8100 level), which is 2469 m (8100 ft) above sea level, is the current mine production level. The intermediate or 7700 level, which is in the initial

Jan 1, 1982

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By Roger Holmberg

INTRODUCTION The driving of drifts is a very important aspect of underground mining. It is not unusual for the percent¬age of rock broken during development in a mine using sublevel caving, for example, to be as much as 25% of the total. If one also considers the amount broken for transport, ventilation, and exploration drifts, one can easily understand that the planning and excavation of drifts play a major part in the total economics of the mine (Fig. 1). Increasing mechanization in mining demands larger tunnel areas for transport and mining equipment. With modern machines the hard work involved in using hand¬held pushers is gone, and a better environment is achieved. More rational methods could be used, but much of the experience the working man acquired by working close to the rock face (such as utilizing the natural weak planes in the rock when he placed the drill¬ing holes) has unfortunately been lost. By having sepa¬rate shifts for drilling, loading, and hauling, more atten¬tion has to be placed upon a well-designed drilling pattern. Some reduction in the number of holes required can be achieved with mechanized drilling because of the larger holes that can be produced. On the other hand, it is probably not possible to achieve the same precision as with pneumatic pushers, and it is difficult to utilize the larger holes because these cause more damage to the re¬maining rock. Recently, however, the precision has be¬come very good with the parallel booms and automatic devices for setting the lookout angle (Fig. 2). A larger arch of the drift roof requires a more carefully executed blasting procedure than before in order to prevent rock fall and to insure a sufficiently long stand-up time. In this chapter, empirical relationships that can be used to design an economic and optimal drift blasting design will be presented. The principles of the calcula¬tion method are based upon the earlier work of Langefors and Kihlström (1963) and Gustafsson (1973). COMPARISON OF EXPLOSIVES To provide for the use of various explosives it is necessary to have a basis of comparison. Several meth¬ods have been developed to characterize the strength of an explosive. Some examples are comparison of values given by (1) calculated explosion energies; (2) the ballistic mortar test; (3) the Trauzl lead block test; (4) the brisance test; (5) the weight strength concept; and (6) the underwater test. However, most of these meth¬ods should be used carefully when stating the breaking

Jan 1, 1982

By J. Kenneth Wittle

The DC Graphite Melter has been shown to be capable of processing radioactive waste materials. The process is characterized by its high temperature capability and operation in a closed system. From an environmental perspective, the control of emissions coupled with destruction for hazardous organic materials is mandatory. These same characteristics may be applicable to the minerals processing industry. Under normal operation, the system reaches temperatures for nominal operation of 1600°C, with an arc temperature in the order of 5000°C. The system temperature is determined by the melt temperature of the material being processed. In testing of a 750 lb/hour unit, temperatures of 2200°C were reached. Current focus is on finding waste treatment and metals recovery opportunities in the metals processing industry for his innovative technology.

Jan 1, 1999

By D. W. Hendrickson

Cliffs views the process as extending from mine planning to cargo loading including auxiliary systems such as material handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This paper discusses the development and results of a strategy to allow and promote implementation of process automation improvements at individual mines based on their economic priorities taking advantage of common systems and concepts for use at multiple mines where practical. Specific process control upgrade projects a Hibbing Taconite Company and the Empire Mine are reviewed in detail.

Jan 1, 1998

"The seventh annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held last February at the SME Annual Conference & Expo in Phoenix, AZ. A total of 21 students entered the poster competition. The students were required to submit one-page abstracts, which were reviewed by the judges, after which they prepared posters to display their work. A panel of judges went to each student and listened as the student explained his/her research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. Recognizing the effort required to participate, the MPD provided monetary rewards to all participants. First place received $1,000; second, $500; and third through seventh, $200. All remaining entrants received $100 each. The winners have their abstracts published in this issue of Mining & Metallurgical Processing. As in past years, there were separate levels of competition for undergraduates and graduates.Now for the winners:Graduate winnersJoseph Halt won first place for research on the use of additives to starch binders to create iron ore pellets. Vivek Agarwal received second for working on using solvent extraction to concentrate lanthanum. Jordan Rutledge placed third for utilizing tannins to depress calcite in fluorite flotation. Fourth through seventh places were Vu Truong, Jacob McDonald, Hunter Sceats and Doug Schriner.Undergraduate winnersLaura Nugent won first place for using high-frame-rate cameras to follow bubbles as they moved from the pulp to the froth in flotation cells. Taylor Graham earned a second-place finish by researching how to acid leach low-grade manganese carbonate.Although its cliché to say everyone’s a winner, everyone can benefit from attending the MPD Student Poster contest. All the students were able to display their work to potential future employers, and industry professionals could talk to the up-and-coming engineers. Next year, there will be another competition for more posters and networking, so get ready to attend.Thank you to all the students for participating; Lisa Schlink for chairing the session; the judges, Aaron Noble, Debra Switzer, Mohammad Rezaee, Nick Gow and Ren Bryce, for evaluating the abstracts and posters; and the MPD sponsors for supporting the competition. This has only been successful with the input of all three groups. Engineering iron ore pellets to reduce their dustinessJ.A. Halt and S.K. KawatraGraduate student and professor and chair, respectively, Department of Chemical Engineering,Michigan Technological University, Houghton, MI, USAIntroductionIron ore pellets are hard spheres made by agglomerating iron ore concentrate and binders. Pellets are the preferred ironbearing feed for blast furnace ironmaking. Starch has been proposed as a binder because it has good adhesive properties, does not contaminate pellets and is relatively cheap. However, starch binders typically lead to weak pellets with rough surfaces, and these can cause high levels of dust within process equipment and when pellets are handled and shipped (Halt and Kawatra, 2014). Our research shows that by adding a small quantity of other additives, pellets made with starch binders become smooth and strong. The newly designed binder leads to significantly lower levels of fines when pellets are handled."

Jan 1, 2016

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By Henry N. McCarl

[ ]

Jan 1, 1966

By J. Villeneuve, M. A. Reute, E. Verhoe

The objective of EU waste policy is to reintroduce used materials into the economic cycle, especially by recycling, or to return them to the environment in a useful state or at least a harmless state. To support decision-making in complex systems, the standardised ISO 14040 life cycle assessment (LCA) method can be used to quantify and to interpret the environmental repercussions of (changes in) a product system from cradle to crave related to a functional service unit. The use of the standardised LCA method at European level can be characterised as a damage-oriented or top-down method, which is often used in product design. Winning, extraction and processing of metals are part of the interconnected worldwide metals production system linked to product design, manufacture and recycling. This complexity cannot be dealt with using LCA. This paper will discuss a dynamic model that deals with this complexity, at the same time providing detailed bottom-up insight into the complex web of materials referred to as Metal Ecology. An example on the replacement on lead in solders will be discussed to illustrate this.

Jan 1, 2005

By J. H. Jennekens

INTRODUCTION "Most people would probably agree that some degree of government control and regulation is essential in modern society, and it will likely continue as an important part of our social organization for the foreseeable future. But most of us tend to be ambivalent about it. In one situation or another we are likely to see government commitment to social benefit programs or regulatory devices either as an expanding encroachment on the freedom of the individual or as an undue interference with private enterprise or with the rules of the market place. But even where there is agreement as to the desirability of government initiatives, either in general or in a particular context, it by no means follows that there will be approval of the mechanisms or procedures used or the means of carrying them out." The above statement is taken from a 1980 Working Paper of the Law Reform Commission of Canada prepared in connection with its study of the exercise of administrative law in Canada and the practices and procedures of administrative tribunals. The Atomic Energy Control Board (AECB) is one such administrative tribunal, and as the federal nuclear regulatory authority, it is responsible for licensing the production, possession and use of nuclear materials, equipment and facilities and enforcing compliance with licence conditions governing the health, safety, security and environmental aspects of the activities involved. Although the AECB was established 35 years ago with the passage in August 1946 of the Atomic Energy Control Act, like many administrative tribunals its role and functions and the regulatory process which it applies have evolved significantly during this period. The changes which have taken place over the years reflect not only the vast scientific and technological developments which have occurred but also the marked differences between contemporary society and the social milieu of the mid-1940s. However, the basic philosophy of nuclear regulation in Canada and the underlying principles of the regulatory process have changed very little. Certainly, the process is far more open in terms of the general public, it has become appreciably more comprehensive and systematic in terms of the depth and extent of both the pre- and post-licensing technical evaluations which are conducted and the ensuing compliance program. Furthermore, it now applies to the whole of the nuclear fuel cycle as well as the industrial, agricultural and medical applications of radionuclides. Nevertheless the following fundamental principles remain unchanged: a. primary responsibility for achieving high standards of nuclear safety and environmental protection in the design, construction, commissioning and operation of nuclear facilities resides with the licensee; b. the credibility of the nuclear regulatory process depends not only upon its technical correctness and practicability, but also upon acceptance by the public-at-large of its perceived effectiveness and efficiency; c. regulatory criteria and principles should be concise, clearly stated and understandable; d. regulatory decision-making should be based upon stated criteria and principles taking into account pertinent scientific and technical facts only; e. fairness and impartiality must characterize all regulatory decision-making; f. the regulatory process should be subject to a comprehensive periodic review and evaluation to ensure that it continues to produce the desired results at justified costs. EXPLANATORY NOTES The mere statement of a set of principles is a relatively simple task. Far more difficult is the explanation of what these principles mean in practical terms. To stipulate that a licensee bears the primary responsibility for achieving and maintaining high standards of nuclear safety and environmental protection may be regarded by some as an attempt by the regulatory agency to evade the responsibilities assigned to it. However, this is not the case. It is unrealistic for anyone to claim that a licensee only complies with accepted norms of public and occupational health and safety and of environmental protection because of the fear of prosecution. The vast majority of citizens conduct their affairs in a proper manner not because there

Jan 1, 1981

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By G. W. Johnston

INTRODUCTION For many years mining at the Stobie mine of the Inco Metals Co. consisted mainly of fill-type mining for higher grade ores and block caving or blasthole open stope mining for lower grade ores. Open stope mining, although quite favorable in the initial stoping phase, has always presented problems in the pillar recovery phase, especially at depth. In 1966, sublevel caving was introduced. This method is ideally suited for low-grade ore and can be applied very successfully to intermediate or higher grade ores providing proper controls are enforced. Sublevel caving has three distinct advantages: it is highly adaptable to mechanization; it recovers the ore in one operation; and it provides adequate ground sup¬port and safety regardless of mining depth. This method does, however, make extra demands, particularly for new types of supporting services. The constant presence of rock makes quality control of the grade of the ore being extracted essential. Increased de¬velopment, different types of ventilation, roadways, and maintenance are only a few of the many changes re¬quired. The care and maintenance of the fleets of diesel equipment and the modification of equipment is a con¬stant challenge. CHOICE OF SUBLEVEL CAVING The question arises, why mine by sublevel caving? Fig. 1 shows a typical problem encountered by the open stope or blasthole mining method. Near the surface there is little or no ground support problem. As mining progresses to an intermediate depth, however, ground failure starts to occur in the supporting pillars. If open mining is carried beyond this point, the critical depth is soon reached, accompanied by hanging wall caving, ex¬tensive pillar failure, and the danger of losing control of the mining cycle. The rock caved from the hanging wall mixes with and dilutes the ore being extracted from the blasthole stopes. Ore losses occur when pillar failure pre¬vents drilling and development of part of the ore. The interruption to the mining cycle causes serious curtail¬ment in production until ground failure is controlled and the mining method changed to adapt to the new conditions. Having recognized the limitations of open stope min¬ing, alternatives were sought. The first alternative (Fig. 2) was to fill the open stopes with sand fill be¬fore extensive pillar deterioration occurred, recover the pillar ore by fill mining, and then convert to total fill mining below. If the ore grade is high enough it can support the costly fill method. Recovery will be at a much slower rate and will therefore extend over a longer period of time. On the other hand, sublevel caving gives complete primary mining recovery in a short time and is very adaptable to mechanization, which is now a necessity to combat spiralling labor costs and give greater produc¬tivity per man. Sublevel caving is ideally suited as a mining method for low-grade ore bodies which eventually reach a criti¬cal depth for open stope mining. DEVELOPMENT The development phase comes first and of course its main purpose is to gain access to the ore and provide a route for ore removal from the mine. Initially a 20% inclined service ramp is driven in the footwall rock (Figs. 3, 4, and 5). It is preferable to start at the top of a mining block and drive the ramp down¬ grade so gravity can assist in mucking the blasted de¬velopment round, and also access can be gained more quickly to the initial production area. The ramp nor¬mally turns at 3.1 rad (180°) about every 152.4 m (500 ft) to keep it reasonably close to the rock disposal

Jan 1, 1982

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

I am deeply honored and grateful to receive the prestigious Gaudin Award. Frankly, I find myself amazed to be included in the company of those outstanding individuals who have previously received this recognition. I am humbly honored to receive this award from an industrial research group. Gaudin was an internationally respected leader of mineral processing. His research contributions widely covered the whole spectrum of mineral processing science and technology, including comminution, size distribution, electrostatics, magnetics, thickening and, especially, the development of flotation theory and application. In his later career, he increased his emphasis on hydrometallurgical technology. In fact, one of his most notable practical contributions was in the development of leaching and ion exchange purification of uranium from low-grade ores. Gaudin catalyzed the trend in mineral processing toward engineering science for a better understanding of process mechanisms and kinetics. He said that those working in academic fields should have an underlying responsibility to the industry they represent. This imposed on him the objective of seeking out research areas that had some relevance to industry's problems. He said, "research without an audience cannot survive." Gaudin performed a most vital service, both in the areas of research in which he was actively involved and through his less-direct influence on current research by his many former students and their students in turn. Interestingly, Gaudin's strength has influenced Newmont Mining Corp. His favorite student was Plato Malozemoff. He had a long and distinguished career with Newmont, beginning as staff engineer in 1945, serving as Newmont's president for more than 30 years and as chairman of the company for 20 years. Newmont's greatest growth occurred during his leadership. Another one of Gaudin's graduate students from Montana School of Mines, Oscar F. Tangel, joined Newmont in 1967. He was a vice president of research and development until 1986. In their efforts, Newmont built a research group, developing the technologies of exploration, geophysics and metallurgy. The Newmont technical facility is named in honor of Malozamoff as "a leader in the development and implementation of new technologies." The mining industry is facing very difficult times, especially in the metals industry. Most metal prices have declined and are still not stable. Most domestic mining companies have largely done away with in-house research and development. Many are reluctant to invest in technology development for which there is not an immediate need. The metal mining industries are focusing on reducing operating costs to survive. Newmont is in the same situation. I appreciate that Newmont's management believes in the importance of research and technology and the impact technology has on the company's value. At Newmont, technology development involves working in the area of applied research. The connections from academic fundamental research to applied research and finally to process development and implementation are very important to develop a new technology. Fundamental research is our foundation, our guidance, giving us direction, providing the principal and mechanism and understanding why it works. Understanding the why will lead to further innovative development. Applied research needs to find the approach to reality, how it works, how to make it better and how to commercialize it. Process development and implementation needs a strong leadership, requires long-term commitment, makes improvements in practical engineering and finally develops an economically favorable process. Implementation is the most important stage in making research a reality. Each stage needs to give feedback to the other stages. Problems need to be understood and solved. Otherwise, the new technology will go nowhere. Simplicity of operation is a key of success in any plant. Necessity is the

Jan 1, 2002

By J. S. Gardner, R. Woolacott, P. D. Robinson

In 1917, U.S. Coal and Coke Company, a subsidiary of U.S. Steel, opened Mine 31 and built the community of Lynch, Kentucky. For the time this was truly a major engineering accomplishment. It was documented in Howard N. Eavenson’s 1939 AIME paper, “Coal Through the Ages.” In 1996, Arch Coal donated the Portal 31 property to Harlan County for public use. In 2003 the Southeast Education Foundation, Inc. and the Kentucky Coal Museum plan to open the Portal 31 Exhibition Mine to the public to tell the story of Kentucky coalmining through the decades. This presentation will summarize the history of the project, efforts to bring it to reality, the engineering problems, and the challenges of providing a safe environment for visitors.

Jan 1, 2003