Search Documents

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By James E. Kolesar

An essential prerequisite to expanding the application of longwall mining techniques in the United States is the development of a better understanding of the mechanics of rock mass deformation near the mined seam, in the inter- burden and at the surface. The results of studies of this type will provide a basis for the development of empirical and/or numerical modeling techniques to predict the rock mass response to mining both near and far from the mined seam. This will lead to improved gate and panel design, resulting in maximum recovery, increased productivity, as well as provide a mechanism for assessing likely surface effects induced by long- wall mining. Presented here is the instrument plan to be used at Kitt Mine No. 1 in the study of rock mass response to two adjacent longwall panels.

Jan 1, 1982

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010

By Mark E. Gershon

Conventional methods of drillhole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drillholes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drillholes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1983

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company&apos;s tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980

By Gary Brierley, Lok Home

"The majority of tunnels for civil engineering applications are now being constructed using some form of mechanical excavation. Beginning in the 1960s with rock tunnel boring machines (TBM), the tunneling industry has introduced both earth pressure balance (EPB) and slurry pressure balance (SPB) soil machines; mixed soil and rock machines and a variety of different mechanical devices for the construction of small diameter tunnels. Over time, these machines have become more powerful and more adaptable to a wider variety of ground conditions; so much so that tunnels are now being constructed in ground conditions and in the vicinity of third-party impacts that would have been considered beyond the state of the art just 10 years ago. Figure 1 is an example of a mixed ground crossover TBM used successfully at Mexico City’s Túnel Emisor Poniente II.All of the above is highly advantageous for the tunneling industry, but it has also placed a much higher level of risk on the performance characteristics of the tunneling machines, on the contractors operating those TBMs and on the manufacturers of those machines. Most of the risks for a tunneling project are associated with creating the space inside of which the finished facility will be constructed. In order to create that space, the tunnel contractor must make many decisions about the best way to excavate the ground, the best way to control the ground at the face of excavation and the preferred method for supporting the ground around the tunnel in a manner that is safe for the workers and stable with respect to all of the overlying and adjacent existing structures. If it is proposed to use some form of TBM in order to build the tunnel, then the TBM becomes central to all three of these activities and becomes an integral part of managing the risks associated with these activities."

Jan 9, 2018

By Herbert F. Nyberg

The Black River Falls Mine is owned and operated by Jackson County Iron Company, a wholly owned subsidiary of Inland Steel Company. It is located in vest central Wisconsin, seven miles east of the city of Black River Falls. This is the first taconite plant in the state of Wisconsin. Iron mining started in this area in 1856 but soon failed due to the low grade ore and crude methods of mining and transportation. Inland Steel Company acquired the property in 1939. Some drilling and test work was done in 1940, but the economics of developing the property at that time were not favolable. Improved methods of concentrating and pelletizing in the 1960&apos;s made it possible to build the present plant. Due to the limited ore reserve of 45,000,000 tons with expected recovery of 33% it was necessary to limit the capacity of the operation to 750,000 TPY with a life of 20 years. There was some concern about an operation of such limited capacity. A million ton operation was considered the minimum size plant for a profitable operation.

Jan 1, 1976

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By T. Rockley, J. Brune

"The mining of tabular deposits accounts for a significant portion of modern production in both underground hard rock and especially, soft rock mining. There is a large discrepancy between the availability of tabular reserves and the amount of development of these deposits, particularly when the deposit has a dip of around 25-50 degrees. This project studied the technical and practical barriers to the mining of these deposits through modern and historical case studies. The primary technical barriers to the development of these deposits are material movement and roof support. The study of historical attempts overcome these barriers and why they failed allowed us to research the possibility of implementing modern technology on previously unsuccessful methods. By modifying some common mining methods, some of these deposits can be mined at only a marginal increase in cost and using readily available equipment. These modified mining methods could make previously underdeveloped deposits to become viable. INTRODUCTION Tabular deposits are defined as orebodies that extend at least hundreds of meters along two dimensions, and a substantially smaller amount along another [1]. Moderately bedded tabular deposits are mined less often than their more horizontal counterparts due to the technical issues they present. These issues often cause lower productivity, higher cost, and more frequent accidents. Moderate dip is a less well defined term; but in this case, it will refer to any deposit which has a dip of at least 20°. This paper will focus on deposits that dip around 25°-50° and are deep enough to require underground excavation methods. These deposits are too steep for most conventional methods yet not steep enough for gravity fed methods to work efficiently. In some cases, this dip range is also referred to as intermediate or steeply dipping. The types of deposits most likely to fall into this category are sedimentary bedded deposits such as coal, trona, evaporates, placers, and other alluvial deposits. Some other types of deposits can fall into this category as well. These include some of the metal reefs such as the Bushveld Complex in South Africa, which was deposited by lava flows, but is tabular. Some areas have dips that fall into the moderately inclined category. There are also some metamorphic deposits such as slate or marble that can have dips of more than 20°. The dip angle of these deposits can cause several challenges. Ore movement becomes more difficult as the exceeds the limits of conventional conveyors, rubber-tired, or tracked vehicles. At the same time the dip is below the angle of repose of the material. This prevents gravity assisted haulage, as the ore and waste will not run downhill by itself. Another common problem in moderately inclined underground mines is roof support. The dip angle can increase the risk of pillar and support failure. This is due to slippage between rock layers, non-perpendicular support of the vertical stresses, and slippage of standing supports. The inclination leads to stresses that are not usually found in typical horizontally bedded deposits. These stresses may require larger pillars that may reduce ore recovery below profitable levels."

Jan 1, 2017

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By D. W. Mitchell

Never increase, reduce, or remove ventilation without unquestionable, compelling reasons. This rule applies every day as well as when fighting fire, attempting to find survivors, or recovering the mine. Right now in some mine a miner is adjusting a regulator in one place to get more air into another. The chances are the desired result will be achieved. Has the miner done a good thing? NO! Solving the immediate problem reinforces the belief he or she can do it again. That "again" might be, to give but one of many examples, the explosion in Greenwich No. 1 Mine. Robbing the proverbial Peter can be the prelude to disaster in a mine. Reducing the airflow is a common practice when fighting a mine fire. In fact, some people have been taught to do that at MSHA&apos;s academy. People who believe that to be proper must be people who never experienced a fire. To fight most fires you have to scramble to get enough air. An explosion demands totally different "thinking". If people are soon to go into the mine, DON&apos;T adjust the ventilation. If teams are in the mine, each affected area must be explored or sealed before making any ventilation change.

Jan 1, 1993

By Paul A. Rittenhouse

First of all, I want to thank John Dunlap for asking me to this AIME meeting in Denver. I was first introduced to Denver and The Rocky Mountains more than ten years ago and immediately decided it was one of the most attractive spots in the world. I&apos;ve come back many times since and still welcome any opportunity to return, even if it means I have to prepare and give a paper on potash. When John Dunlap gave me this assignment, he told me that the program would include papers on the geology of potash, papers on new discovered potash deposits and new mines and asked me to discuss potash from the commercial point of view. He also asked me to include a supply/demand outlook for potash. However, one thing he did not mention was "how far into the future he wanted me to look" and it seems to me the time element is a crucial factor to you who are both geologists and miners as well as to me. In your case, you have to look far enough into the future to give you time to explore, find, evaluate, develop, and bring into production a commercial deposit. My mining associates and friends don&apos;t agree on how long that takes but it&apos;s probably somewhere in the range of eight to fifteen years. But, they all agree on one thing and that is that the time required is continually getting longer. Now my time problem is just the opposite. It is "relatively" easy, and I stress relatively, to identify and evaluate the importance of the various factors that impact on both the supply of and demand for a commodity such as potash if the time period is today. It gets a little tough if one has to project into tomorrow or next week or next month. And when we start talking in terms of a year, five years or ten or fifteen years, things really get sticky and the old crystal ball becomes mighty cloudy. But we economists and forecasters are not known for our temerity so let me get on with the job at hand and take a look at the world potash supply/demand outlook.

Jan 1, 1978

By S. Mohanan, C. R. Kumar, S. K. Bhoja, T. Venugopalan

"A pressing issue that has often been the topic of discussion in iron-making operations in India is the high content of alumina in the country’s iron ore deposits. The presence of alumina has hampered production by affecting slag fluidity, and thereby the hot metal quality. Iron ores from Indian mines are generally rich in hematite, with traces or small amounts of goethite/limonite, kaolinite, gibbsite and quartz reported from time to time. In day-to-day production, emphasis is placed on checking the chemical analysis of product samples, but the true solution to the alumina problem lies in estimating the mineralogy of the ore samples. We developed a mathematical model, based on singular value decomposition, to predict mineralogy from classical chemical analysis. We then used X-ray diffraction patterns, scanning electron microscope analysis, and grain counting with an optical microscope to determine actual mineral compositions and to test the values predicted by the model. The results indicate that with regular calibration, the model can be used as a simple, fast and effective tool to predict on a regular basis the mineralogy of multiple samples.IntroductionIndian blast furnaces use high-grade iron ores (as lumps or as sinter) and coke (obtained from the destructive distillation of coal) as raw materials for the production of high-quality hot metal to be converted into different steel products through the Linz- Donawitz process. The iron ores are mainly sourced from the Singhbhum region of Odisha and Jharkhand states, the Bailadialla region of Chattisgarh state and the Bellary region of Karnataka and Goa states, and are mainly classified based on size as (1) lump ore (fed directly into blast furnaces), (2) fines (converted into sinter/pellets and fed to blast furnaces) and (3) slimes (< 0.15 mm; currently dumped in huge slime ponds). Any variation in the quality of the ores supplied results in variations in the production trends of hot metal."

Jan 1, 2015

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003