Search Documents

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Secondary blasting requirements have varied from one shot per 27 tonnes (30 tons) to one shot per 900 tonnes (1,000 tons) of ore. Geology, structure, cave abutment loads, and location of the ore in the column all affect the amount of oversize boulders (greater than three-fourths cubic meter or one cubic yard) that require secondary breakage. The primary method of breakage utilizes cone charges (plastic funnels filled with an emulsion) placed on accessible oversize rocks. Hangups in the brow area of the drawpoint are drilled with a self contained diesel hydraulic drill and loaded with gelatin dynamite. High hang-ups located beyond the reach of the secondary drill are "bombed" in with strategically placed emulsion bundles or ANFO bags loaded in place though a sectioned aluminum pipe.

Jan 1, 1994

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014

By Paul H. Johnson

A new system for leaching many types of ores has recently been developed on a commercial basis by J and J Research and Development, Inc. of Hanover, New Mexico. This revolutionary new leaching system consists principally of three new leaching reactors; viz, (1) a large, air-agitates, column-like reactor for leaching crushed ores that is constructed in an underground environment and has the inherent ability to do a very efficient job of leaching, (2) a vat-like, air-agitated vessel for leaching an rinsing finely ground ores and , (3) an air-agitated copper precipitation column that is built underground and utilizes an inexpensive dense or heavy scrap iron as a copper precipitant. Each of these new reactors have been used in a large leaching plant near Hanover, New Mexico.

Jan 1, 1973

By Robert S. Lehto

Zinc concentrates received in La Oroya zinc refinery are marmatitic in nature, contain about 11% iron and traces of other metal values, Figure 1 shows the zinc circuit. The calcine from the roasted concentrates is leached in spent zinc electrolyte. Major part of the impurities is iron which has been oxidized to its trivalent form, This is the origin of the zinc leach residue for which the ZILERET process was developed and so named. The impure liquor from the leach is sent for purification and thence to electrolysis- zinc deposits on aluminum cathodes from which: it is stripped, melted and cast into slabs Typical assays of zinc calcine and leach residue are given in Table 1. Metal values contained in the leach residue, without counting any value of iron, amount to roughly $130 per short ton.

Jan 1, 1969

By B. L. Bessinger

Because of a, work stoppage at the Carlsbad plant, IMC faced the challenge of operating a 24-hour-a-day mine and plant with inexperienced maintenance and production crews. This is an underground mining operation, using the room-and-pillar mining- method. The mine was entirely, mechanized with conventional equipment, was hoisting an average of 13,539 tons off ore per 24 hours, and employed a, mine maintenance group of 100 men. The 100-man, mine maintenance group was equally divided between mechanics and electricians. In re-forming this maintenance group, two main objectives were to be achieved (1) a general upgrading off the intelligence level; and (2) the elimination of craft lines for greater flexibility.

Jan 1, 1966

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By G. A. Kordosky

Solution mining followed by solvent extraction-electrowinning (SX-EW) is one possible way to economically extract copper from ore bodies which cannot otherwise be profitably exploited. Published costs for the unit processes of SX and EW are out of date especially in view of the newer reagents now available and the newer circuit configurations, This paper updates the costs for SX-EW in 1985 dollars and also discusses some of the trade-offs which must be made when designing an SX-W plant.

Jan 1, 1986

By Thomas P. Meloy

The understanding, quantification and use of locked particles. Specifically discussed is the use of Textural Transforms (Meloy, 1991) for the implementation of the Interfacial Area Conservation hypothesis (Meloy, 1984); the quantification of the locked particles as a function of fragment to inclusion size ratio; and the selection of set points.

Jan 1, 1991

By Robert G. Beverly

The presence of radioactivity in uranium mill wastes has resulted in somewhat unique waste disposal methods. In addition to the common problems of disposing of large quantities of solid wastes, neutralizing acids, minimizing dissolved heavy metals, and clarifying all liquid effluents, the uranium mill operator must sample and analyze liquid effluents for micro-micro quantities of radionuclides such as, radium-226, thorium-230 and lead-210. Special disposal methods or decontamination procedures are required to meet the stringent limitations established by the U. S. Atomic Energy Commission on the concentration of radionuclides in liquid effluents. Routine monitoring of the receiving stream is also normally required. In recent years there has been a growing concern about the radioactivity remaining in the uranium mill tailings, particularly at the sites of shut-down or dismantled mills. The State of Colorado, in cooperation with the industry, has adopted regulations for stabilization of inactive uranium mill tailings. The Mining and Metals Division of Union Carbide operates mills for the recovery of uranium and vanadium at Uravan and Rifle in Colorado and a mill in the Gas Hills of Wyoming for uranium production. The company also owns former mill sites on which mill tailings are located at Maybell, Rifle, and Slick Rock in Colorado and at Green River, Utah. The purpose of this paper is to describe the methods used by a few uranium mills, largely those operated by Union Carbide Corporation, to dispose of radioactive wastes, to discuss briefly the regulations under which the mills operate, and to present reference information on the subject.

Jan 1, 1968

By R. Cohen-Alloro

Classical apparatus for granulometric separation generally have limited applications which are found either in the level of the size of separation or in that of the accuracy and the efficiency of the separation or in that of the rate of feed. In industrial practice, the classification of the products of coarse dimensions generally poses no problems. On the contrary, the separation of fine particles presents some difficulties, however the apparatus is used (mechanical classifiers, curved screens and sieves, hydrocyclones, etc...). These difficulties are due to hprfections of separation, rather high cost prices, and sometimes large amounts of recycled materials.

Jan 1, 1970

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By A. Noble

For the past 30 years, process flowsheet design has been accomplished largely through modeling and simulation. This approach provides circuit designers the freedom to test various separation approaches while minimizing physical and human resource requirements. The Limn® software provides a unique approach to process simulation, through a Microsoft Excel interface. While the software comes with standard process models for numerous unit operations, the Excel calculation environment and the accompanying VBA platform provide a convenient interface for custom model integration, even for non-experienced programmers. This feature is especially useful for university students in introductory process modeling and simulation-assisted flowsheet design courses as well as experienced practitioners with proprietary process models. This paper shows how the Limn® software may be used to solve basic process engineering problems as well as more comprehensive circuit design challenges. Industrial examples as well as opportunities for training and education are presented.

Feb 23, 2014

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO's Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019