Search Documents

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By D. R. Nagaraj

Based on our finding that commercial copper chelating solvent extractants such as LIX65N® and LIX63® are excellent collectors for copper minerals, a detailed study was made using several water-soluble chelating agents belonging to the class of aromatic hydroxyoximes and having a gradual structural variation. A basic study of the system salicylaldoxime-tenorite was also carried out. Microflotation tests as a function of concentration of oxime, pH, addition of copper etc., using oxidic copper minerals such as chrysocolla and tenorite, and batch laboratory flotation tests using synthetic mixtures of quartz and oxidic copper minerals were carried out. The studies were aimed at an understanding of the collector function of the hydroxyoximes and of the general flotation behavior in these systems, in addition to studying the structural aspects of oximes vis-a-vis flotation. The results have demonstrated that all of the hydroxyoximes studied here have comparable collector property, and in all cases the oxime was found to be partitioned between the mineral surface and the copper in the bulk aqueous phase in the form of a bulk copper chelate. The occurrence of the latter could be accounted for by the formation in the bulk phase of a chelate between oxime and copper released from the mineral and/or by the detachment of the surface chelate. The role of surface and bulk chelates in flotation is discussed based on the results of partitioning of chelating agent into bulk and surface chelates in the system salicylaldoximetenorite. The effect of substitution of CH2 groups or benzene ring in the chelating agent molecule on its collector property is also discussed, in addition to the finding that only the anti-isomer has the ability to collect.

Jan 1, 1979

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

Conventional wisdom in the mineral processing industry leads one to believe that pressure oxidation of refractory carbonaceous (preg-robbing) ores is not a practical approach to process development. Initial acid pressure oxidation testing on carbonaceous sulfide ores at the Twin Creeks Mine supported this conventional wisdom. After testing other refractory process options, including air and oxygen enriched roasting, Santa Fe Pacific Gold decided to take a second look at pressure oxidation, using conditions outside the normal range of conventional practice. A combination of very fine grinding and high operating temperature and pressure resulted in significant increases in gold extraction. This paper details the effect of operating parameters developed for Twin Creeks on gold recovery, sulfur oxidation, carbon oxidation/passivation and preg-robb through the laboratory and pilot plant investigations.

Jan 1, 1995

By Felicia F. Peng

Using granular media for removal of soluble manganese from mine water and industry waste stream has the advantage of forming a compact surface layer of manganese oxide coating on the media. This process can avoid the step involving the separation of voluminous sludge of manganese hydroxide by the high-pH method for soluble manganese removal. The removal of soluble manganese is accomplished by adsorption and oxidation. The adsorption of Mn(II) on the manganese oxide-coated media was rapid through the specific adsorption and may be due to the ion exchange of hydroxyl ions on the manganese oxide by Mn(II). In the subsequent step, the adsorbed Mn(II) form the intermediate manganese complex on the manganese oxide product is oxidized with dissolved oxygen or other available oxidant source in the aqueous solution. This paper presents the efficiency of removal of soluble manganese from mine water by using a laboratory fluidized bed and the recovery of manganese oxide coating on the anthracite coal particles. In order to accelerate the formation of the manganese oxide layer on the surface of anthracite media, dilute potassium permanganate solution is used as an active oxidant. The effects of operation parameters on the manganese removal including pH, flow rate, concentration of feed and oxidant dosage are evaluated.

Jan 1, 1996

By N. L. Dorset, K. L. Heasley

Unfortunately, mining and mining accidents have gone hand-in-hand since man first started to extract ore from the ground. In the first published treatise on mining, De Re Metallica, Georgius Agricola (1556) stated that cold, water, dust, stagnant and foul air, roof falls, falls from ladders and demons all caused injury and death in the mines of his day. Although demons are no longer considered a cause of accidents in modern mining, the other factors remain with us still. The United States government started keeping track of fatalities with the establishment of the federal Bureau of Mines in 1910. Successor agencies, such as the U.S. Mine Safety and Health Administration (MSHA) continue to track fatalities today. Looking at the records, it can be seen that coal mine fatalities dropped from 2821 in 1910 to only 27 in 2004. The reduction in fatalities and injuries didn’t “just happen.” It took concentrated effort from the entire mining industry: miners, supervisors, safety officials, mining inspectors and mining researchers. But first, specific hazards must be identified before they can be corrected. In past, coal mining accidents have been analyzed by: type (roof fall, electrical, etc), mine attribute (location, seam height, etc.), and aspects of the mineworker (work experience, job classification, etc). Much of this research helped to direct the industry’s attention to where additional vigilance and safety training was needed. No doubt this directed effort has led, at least in part, to the decrease in coal mining fatalities. This paper takes a novel look at coal mining fatalities: it examines the risk of fatalities based on how long the mine has been open.

Jan 1, 2006

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By F. Turatti

Rio Tinto is one of the world's largest mining companies, involved in every stage of metal and mineral production, producing aluminium, copper, diamonds, coal, iron ore, uranium, gold and industrial minerals. Operations are in more than 50 countries in multiple continents and vary in location between large urban centres, regional industrial complexes and remote regions. A risk-based strategy was developed by Rio Tinto to manage its air quality impacts on a global scale. The strategy consists of three objectives ? improving air quality performance, developing industry leading practices and engaging and influencing in air issues. This paper discusses three major successes achieved this approach. Firstly, how air shed resources are managed in constrained air sheds. Secondly, how financial modelling is used to value air quality constraints, and thirdly, how a rigorous and comprehensive e-learning course is used to improve the overall level of air management knowledge of Rio Tinto?s environment managers.

Feb 27, 2013

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By CASSANDRA L. HOEBBEL, PATRICK L. YORIO, Emily J. Haas

This study revealed significantly less favorable perceptions of the existing organizational safety climate among workers in the underground coal-mining sector compared with those in the industrial-minerals and sand, stone and gravel (SSG) sectors. Consequently, it is important to consider pragmatic ways in which health and safety management systems (HSMS) in coal mines can alter processes to improve these perceptions. Given the interdependencies of safety climate factors and HSMS elements, researchers explored mineworker perceptions of the supportiveness of organizational safety climate factors among mineworkers and identified significant differences in perceptions across sectors. In this paper, we suggest that health and safety professionals in underground coal mining and organizations with fewer resources or less mature HSMSs focus on these factors to bolster support for proactive safety performance. Potential barriers to implementing or improving relevant HSMS elements and ideas to help foster more favorable perceptions of organizational safety climate are also discussed.

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972