Search Documents

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By Carl Pinches

Underground or surface mining is only the first stage in the ore mining process. Once the ore is mined, it is transported to the surface for further processing. Generally, this is done to extract the particular metal or other component of the ore that has commercial value in its purified form. In its raw state, there are typically between 4 and 7 g/t (0.12 and 0.2 oz/st) of valuable material from rock mined. Once on the surface, the ore is crushed and milled in order to obtain smaller rock particles and to expose the minerals that contain the desired metal or component. Mixing the milled ore with water, a process known as ?froth flotation,? can be employed. This technique consists of a series of tanks, or ?cells? through which the process liquid flows. To obtain the maximum recovery, the milling and flotation process will often be repeated a second time. An increase between 100 and 1,000 g/t (2.9 and 29 oz/st) of rock following this stage of the process is typical. Efficient recovery is key to maintaining a profitable mining operation. The measurement and control of the froth flotation process is vital.

Jan 1, 2010

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

By J. Harrison Daniel

Were the legislators and politicians responsible for the closing of the U.S. Department of the Interior?s Bureau of Mines (Bureau) in March 1996 fully aware of what they were doing? Throughout the United States? history, the domestic mining and minerals industry has been largely responsible for the nation?s growth and prosperity that had made it a world leader. The mining and minerals industry made it possible for the young nation to catch up with Europe during the Industrial Revolution, played an essential role leading to victories in World Wars I and II and was a core ingredient for continued economic growth. For a number of decades, America?s import dependency on non-fuel mineral materials has continued to increase. (USGS Mineral Commodity Summaries). Developing domestic resources to meet current and future demands ? particularly those resources considered to be of strategic and critical value to national security ? is necessary. Federal involvement is required since many of these resources are located on public lands. Another reason for federal involvement is that the success of the industry depends on long-range research programs and advances that may take up to 25 years to become commercially available. This situation requires federal partnership to coordinate the programs necessary to collectively involve the industry, individual mining companies and colleges and universities. So, how was it possible to close a federal agency that had contributed so much to the nation?s welfare in a mandated 90-day period, with more than 1,200 employees losing their jobs?

Jan 4, 2010

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By D. Washington

The US economy and the demand for nonfuel minerals grew at lower rates in 1995 than in 1994. Demand for major metals, such as aluminum, copper and steel, was mixed but relatively stable. The building industry, including highway construction, helped to support modest overall growth in demand for industrial minerals. The value of processed materials of nonfuel mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10%compared with 1994 (Fig. 1). The estimated value of US raw nonfuel minerals production during 1995 was $38billion, about 7% more than in 1994. The value of US minerals production has increased in 30 of the last 35years.

Jan 1, 1996

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By Kiseong Hyeong, Young-Tak Ko, Gee Soo Kong

"The benthic environmental impact experiment addresses environmental impacts at a specific site related to deep-sea mineral resource development. For such a purpose, since 2010 we have carried out essential environmental research at both the BIS and a preservation site. We have acquired several tens multi- or box core samples at 32 sites within the BIS especially between 2011 and 2013, aiming to examine the basic properties of surficial deep-sea sediment as the potential source for deep-water plumes.In this study, we present physical the properties such as water content, shear strength and also geochemical properties such as major elements, rare earth elements (REEs), heavy metal contents at the BIS. Such proxies vary distinctly according to the Facies association. The lithology of all core sediments in the BIS corresponds to both Association Ib (Unit I/Unit II) and Association IIIb (Unit I/Unit III) on the basis of the KORDI classification (KORDI, 2004); Unit I is watery mud and dark grayish brown (10YR4/2) to dark brown (10YR4/3). Unit II is highly bioturbated mud and brownish yellow (10YR6/6). Unit III is very dark brown (10YR3/2) to black (10YR2/1) mud. Physical properties of these sediment types show that Association Ib is distinct from Association IIIb. The vertical profile of water content changed more sharply in Association IIIb probably due to compaction; water contents varied from 230 to 300% in Association Ib and changed from 200 to 250% in Association IIIb. The vertical profiles of shear strength are also quite different between Associations; the profile curve in Association IIb is much more gentle due to bioturbation."

Sep 1, 2014

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

By Gregory D. Savage, Bruce M. Everett

Introduction The growing role of Colombia as a major supplier of internationally traded steam coal has been widely discussed in the industry. Although Colombian coal has been produced and exported in small quantities for a number of years, the country's position as a major coal exporter began in earnest in 1985 with the first commercial exports from the Cerrejon North Block Project. The mine is located on the Guajira peninsula in northeast Colombia, about 145 km (90 miles) from the coast (Fig. 1). In addition to the mine itself, the project involves construction of a dedicated railroad and port. This forms a modern, efficient, and integrated system. The project is embodied in a 50-50 association contract between International Colombia Resources (Intercor), a wholly-owned subsidiary of Exxon, and Carbocol, the Colombian state coal company. Intercor and Carbocol share investment and operating expenses equally. Intercor has the additional responsibility of managing operations on behalf of the partners. Each partner is entitled to 50% of the coal produced, and each markets its share separately. The project is a multi-seam, truck and shovel operation, based on large reserves (2 to 3 Gt or 2.2 to 3.3 billion st) of high quality bituminous coal. Exports began in the first quarter of 1985, at modest levels through what is called Early Coal Facilities. The permanent coal handling system began operation in February 1986. Production will increase rapidly in each of the next few years, reaching the design capacity of 15 Mt/a (16.5 million stpy) in 1989. Based on available resources, however, the resource will support expansion, and continued growth in production into the 1990s is feasible. Importance of transportation The success of a new coal export venture, such as Cerrejon, depends heavily on efficient transportation. In the international coal industry, overland and ocean transport can in some cases account for 40% to 50% of the final value of the product. Many coals, such as western US subbituminous coals, cannot reach export markets at all because of their low heat content and great distance from export markets. By the same token, low-grade resources are often commercially attractive for local markets even in the face of competition with much higher quality coals from distant sources. Figure 2 shows the growth in steam coal imports into Europe, the largest trading market. Through

Jan 6, 1986

Mineral liberation data are routinely obtained for a wide variety of applications, including ore characterization and characterization of various metallurgical test products obtained in bench-scale laboratory testwork. Newmont Mining Corporation owns several properties in the Carlin Trend containing refractory gold ores. These ores are generally difficult to treat and have to undergo several processing stages for gold recovery. At Carlin?s Mill 5 operation, flotation is used to pre-concentrate some of these difficult ores to produce a sulfide concentrate to feed the roaster. It is of interest from a flotation perspective to be able to study the floatability of pyrite, arsenopyrite and arsenian pyrite, since these minerals all have different quantities of gold associated with them, and have to be recovered to ensure a successful separation has been achieved. In this paper, a detailed MLA study on several Carlin ores was undertaken on samples from flotation tests, using air or nitrogen as flotation gas, specifically to study the differences in floatability characteristics, which ultimately impacts overall gold recovery. I

Jan 1, 2009

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By G. Luttrell

Coal preparation plants play an important role in modern society by providing high quality feeds for coal-fired utilities, industrial boilers and metallurgical coke facilities. Unfortunately, field data indicate that preparation plants are often not operated under optimum conditions, resulting in lower productivity and lost profits. In many cases, this shortcoming can be attributed to a failure by plant operators (i) to recognize the importance of correctly adjusting plant operating conditions to accommodate requirements dictated by coal sales agreements within different coal markets and (ii) to properly account for variations in product moisture with particle size across different plant circuits. This paper discusses the important influence of moisture constraints on preparation plant optimization and provides a case study to illustrate the potential gains that can be realized via proper understanding of plant moisture control.

Jan 1, 2009

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007