Search Documents

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By James M. Riddle

A discussion of frequently asked questions may help individuals trying to interpret subsidence regulations or prepare permit applications. The subsidence permitting process involves just one part of the mass of Surface Mining Control and Reclamation Act regulations. But of the 18 main SMCRA sections, subsidence is critical to the permitting process for coal operators. It's an area in which applicants have had problems interpreting regulations and preparing permit applications. Of 22 western states, only Wyoming, Montana, Colorado, and Utah heave thus far received approval for their mining and reclamation plans. The other states are now involved in the permit application process and will be dealing with SMCRA regulations for the next year or so. Some state programs, when approved, may differ substantially from the federal SMCRA program. But, to be approved, the state programs must be deemed equal to or more stringent than the federal regulations. SMCRA regulations apply to any coal operation "that exhibits surface effects." Thus they apply to surface strip mines as well as underground coal operations. The regulations do not apply to hardrock mining operations. Since August 3, 1977, the government, industry, and the public have wrestled with SMCRA. They have struggled through an initial program with the US Geological Survey; a new agency, the Office of Surface Mining Reclamation and Enforcement (OSM); an interim program; and a "final" permanent regulatory program. Even now, OSM is reluctant to publish formal program guidelines because: •The regulations are still in the process of judicial review. • Some approvable state programs will supersede the federal regula¬tions. • The flexible regulations are open to interpretation, which is desir¬able to maintain. •Guidelines could be misleading until regulations and interpretations are revised and finalized.

Jan 12, 1980

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

By Carl Johnson, D. R. Todd

The Blue Ridge Low Level Outlet (LLO) was a design/build contract to provide a secondary means of discharging water from the Blue Ridge Reservoir. The project involved driving a 3.25 m (11 ft) modified horseshoe tunnel by 293.5 m (963 ft) long utilizing conventional drill and blast methodology. The intake shaft and structure were constructed inside of a sheet pile cofferdam surrounded by a maximum of 20.1 m (66 ft) of water. The shaft was excavated 4.87 m(16 ft) diameter to a depth of 12.8 m (42 ft) below the tremie slab elevation. Steel lining, including a transition from 3.66 m to 2.74 m (12 to 9 ft) diameter and a90 degree elbow were installed in the inlet shaft and then backfilled with concrete. This paper will describe the RFP phase, the design phase, challenges of the underground construction and contractual challenges.

Jan 1, 2005

By M. A. Stoakes, H. D. S. Miller

Surface subsidence is becoming an increasingly important factor in the economics of mining Louisiana salt domes due to, amongst others, excessive shaft deformations and land loss to encroaching sea water. The vast majority of subsidence studies have been undertaken on bedded, tabular deposits. It is important to understand the causes of subsidence due to mining domal salt and how it can be minimized. The paper will review the major differences between subsidence caused by domal and tabular evaporite mines, the problems encountered in predicting subsidence, the factors that influence subsidence and, finally, possible alternative mining methods.

Jan 1, 1986

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By L. Ou

This paper reports on research on leaching pyrite in a germ-free system. The effects of mineral particle size, pulp potential and various oxidation agents on pyrite leaching were studied. The results indicated that a smaller mineral particle size leads to a higher leaching rate of pyrite. The optimum results were obtained with a mineral particle size of -0.037 mm. The pulp potential reflected the leaching process and an increasing pulp potential improved pyrite leaching. The leaching rate rapidly increased with the addition of oxidation agents such as Fe3+ and H2O2. However, the precipitate generated by ferric ion coated the surface of the pyrite and prevented further leaching.

Jan 1, 2007

By Carlos Henrique Turolla Maia, Ulrich Maidl, Marc Comulada, Julio Claudio Di Dio Pierri

"Pure sands are typically the domain of slurry shields due to their high permeability and their granular characteristics. However, the Earth Pressure Balanced (EPB) shield machine technology has advanced in recent years with improved conditioning agents and shield machines that are equipped with slurry injection facilities and alternative mucking methods. These new so-called hybrid EPB machines have steadily increased the range of application of the EPB technology. The contribution discusses the capacities and operational features of hybrid EPB vs. slurry shield technology in pure sands. At the example of the Metro Line 4 in Rio de Janeiro (Brazil), the contribution shows that hybrid EPB tunneling in pure sands is possible and it is compared with a state-of-the-art slurry shield project as the KASIG project in Karlsruhe (Germany). Furthermore, the control of the support pressure by means of foam conditioning and slurry injection in conjunction with a close, real-time monitoring of machine parameters is discussed. INTRODUCTION Slurry shield and EPB technologies have both undergone significant developments in recent years, leading to the use of parts of one technology in the other and even to completely hybrid systems. Also the ranges of application (see recommendations by DAUB (DAUB 2010)) of both technologies have been shifted far beyond their original limits and are largely overlapping by now. Nevertheless, the basic principles of face support remain unchanged. Exploiting the possibilities of process data analysis (Maidl 2014), the interactions between the ground and the shield machine are a matter of research and have been intensely investigated. PRINCIPLES AND CALCULATION OF FACE SUPPORT PRESSURE Figure 1 shows the principles of two approaches for the determination of required support pressures: kinematic methods and numerical methods. Kinematic methods that are employed for the assessment of face stability only consider the situation in front of the TBM. The required face support force is determined by means of an assumed failure wedge that would form in ultimate limit state. Based on the ground properties, the vertical surcharge and the self-weight is transformed into a horizontal force along a virtual sliding surface. This horizontal force is to be balanced by the face support. The calculation results are amended by respective partial safety factors for water and earth pressure and the method-specific support pressure fluctuations are added."

Jan 1, 2016

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

By H. Sarvamangala

Biomineralization of manganese on titanium condenser material exposed to seawater has been illustrated. Biom-ineralization occurs when the fouling components, namely, the microbes, are able to oxidize minerals present in water and deposit them as insoluble oxides on biofilm surfaces. Extensive biofilm characterization studies showed that an alarmingly large number of bacteria in these biofilms are capable of oxidizing manganese and are, thereby, capable of causing biomineralization on the condenser material exposed to seawater. This paper addresses studies on understanding the exact role of the microbes in bringing about oxidation of manganese. The kinetics of manganese oxidation by marine Gram-positive manganese oxidizing bacterium Bacillus spp. that was isolated from the titanium surface was studied in detail. Manganese oxidation in the presence of Bacil-lus cells, by cell free extract (CFE) and heat-treated cell free extract was also studied. The study confirmed that bacteria mediate manganese oxidation and lead to the formation of biogenic oxides of MnO2, eventually leading to biomineralization on titanium surface exposed to seawater.

Jan 1, 2008

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By J. A. Ober

China, Mexico, Spain and Turkey are the leading producers of celestite (strontium sulfate), the most common strontium mineral. Of an estimated 510 kt (562,000 st) of celestite produced worldwide during 2004, 98 percent was produced in those countries. Deposits of strontianite (strontium carbonate), another strontium mineral, have been identified in China and Malawi. Relatively small quantities are reported from the deposit in China. Although celestite deposits occur in the United States, no domestic celestite has been mined since 1959.

Jan 1, 2005

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991