Search Documents

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By Arnold O. Tanner

The recession that took hold of the domes-tic mining industry in 1981-82 finally abated somewhat in 1987, resulting from increases in many commodity prices, especially in the metals sector, and from continuing success in lowering operating costs. By no means was the work finished; the mining industry was in a sense entering a new era. The struggle for survival was still very evident for many companies and various commodities, but increasing productivity and profits were accompanied by indications that these trends were more long term than short term. Raw nonfuel minerals produced in the United States during 1987 had an estimated value of $26.3 billion, an increase of $2.9 billion over the 1986 value. This is the fifth consecutive year that the value has increased. Except for a decrease in 1982, the value each year has increased since 1971, or 15 of 16 years. The value of raw metals production increased by an estimated 28%, an impressive improvement since the drastic fall in 1982. Industrial minerals growth was comparatively flat, with an estimated in-crease in value of 0.1 %, continuing a trend of the previous 2 years. Metal mine production dropped considerably in 1982 and maintained its resultant lower level until 1987, when production significantly recovered.

Jan 1, 1989

By E. A. Sondreal

The Bureau of Mines investigated the use of lignite char for producing carbon disulfide; CS2 production rates were as high as when wood charcoal was used as raw material. The maximum space velocity for CS2 produced in the bench-scale study was 9,280 hour-1, reacting sulfur and lignite char at 792° C. The reaction temperature and the temperature at which the char was carbonized were the two most important factors in determining CS2 production rates. Increasing the carbonization temperature in nitrogen from 400° to 900° C advanced the temperature at which carbon disulfide was first produced from 550° to 850° C. The average activation energy for reacting chars with sulfur was 44,000 cal/g mole. The reaction was first order with respect to the partial pressure of sulfur. Increasing the rate of sulfur admission caused a decrease in rate of production at otherwise similar conditions. Rates were not affected by either char size or sodium carbonate catalysis. High space velocities at moderate temperatures using inexpensive lignite chars could offer an economic advantage in the manufacture of carbon disulfide provided that yields were attractive.

Jan 1, 1967

By E. F. Foerster

The Bureau of Mines used a diphenyl ether calorimeter to determine the heat contents of natural and synthetic blast-furnace slags. For solid slags, enthalpy (HT-H298) at 1,448° to 1,680° K ranged from 282.1 to 348.5 cal/g (±3 percent); liquid slag values were 400.1 to 514 cal/g (±3 percent) in the temperature range between 1,626° and 1,890° K. Experimental results for liquid slags were 14.3 to 16.2 percent higher than the enthalpies calculated from thermodynamic tables; values for solid slags ranged from 5.3 percent lower to 3.9 percent higher than calculated values. Experimental results for liquid synthetic slags ranged from 14.9 to 24.3 percent higher than the calculated enthalpies; values for solid synthetic slags were from 1.0 to 3.4 percent higher.

Jan 1, 1967

By Kevin Malone

Chrysotile asbestos occurs in many counties in California, and a small production had been reported at times, but development of deposits had been disappointing. A reconnaissance survey by the Bureau of Mines indicated that several deposits in the serpentine belt in Shasta, Trinity, and Siskiyou Counties might contain enough asbestos of filler grade to supply the growing demand on the west coast. Accordingly from 1956 to 1958 parts of the Mount Eddy and Shasta View deposits were investigated by trenching and diamond drilling to determine their potential. The work comprised construction of roads, bulldozer trenching, excavation of areas for diamond drilling, sampling, and upping. The trenches were excavated to expose the surface extent of some of the asbestos-bearing areas, To determine the downward continuation of asbestos-bearing sections and to secure samples for test purposes, six diamond drill holes, totaling 1,738 linear feet, were drilled in two selected areas. The trenching and core-drilling indicated that the asbestos-bearing material occurs as ribs and lenses of varying thicknesses in a broad belt of serpentine, about 600 feet wide and several miles long,

Jan 1, 1962

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department?s Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By C. C. Popoff

The Dunkleberg district is in the Flint Creek Range of the northern Rocky Mountains, about 45 miles northwest of Butte, Mont. Silver - lead and zinc mineralization occurs over an area 4 miles long from north to south and 1 to 2 miles wide from west to east. Ore in appreciable quantity has been produced, mostly from the Forest Rose group of mines in the southern part of the district. The Forest Rose mine was the largest producer of lead and the Wasa mine, a mile farther south, the main producer of zinc. The total output of ore from these properties during World War II was 113,000 tons, or 98.2 percent of the total recorded production of the district. The Wasa mine was examined by a Bureau of Mines engineer2/ in 1944. Subsequent investigations during 1946, 1947, and 1948 included trenching and drilling Fn the Wasa area and examination of the Forest Rose and other mines.

Jan 1, 1953

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By Ted C. Briggs

A special high-pressure Burnett-type compressibility apparatus was constructed and used to determine compressibility factors for pure helium, pure nitrogen, and nine helium-nitrogen mixtures containing 89.47, 79.04, 69.69, 60.09, 49.24, 41.02, 30.99, 20.53, and 10.67 mole-percent helium. A total of 161 runs were made consisting of 2,355 observed pressures. Data were obtained at 0°, 25°, and 50° C and at pressures to 1,000 atmospheres. A power series in the reciprocal volume, commonly called a Leiden series, is used to represent the compressibility factors. Three parameters in the series are required to represent helium, five parameters to represent nitrogen, and from three to five parameters to represent the mixtures. Compressibility factors are believed to be accurate to better than 0.1 percent over the entire pressure, temperature, and composition range.

Jan 1, 1972

By E. J. Kloos

One phase of the work of the Bureau of Mines in health and safety is promoting the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum-performance requirements for the approval of self-contained breathing apparatus (1),4/ gas masks (2), supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks) (3), dispersoid (dust, fume, and mist) respirators (4), and nonemergency gas respirators (chemical-cartridge respirators) (5). Approval tests of self-contained breathing apparatus are conducted by Health and Safety District B; approval tests of other types of respiratory-protective devices are conducted by the Branch of Health Research. Manufacturers of respiratory-protective devices may submit their equipment to the Bureau of Mines for approval under the requirements of these schedules. If the device, when tested by the Bureau, meets the schedule requirements, a certificate of approval will be granted, which not only states that the equipment has passed the schedule requirements but also gives information about the limitations of the device. If it is found at any time that approved devices do not meet the requirements of the pertinent schedule, the Bureau may rescind approval.

Jan 1, 1959

By Michael V. Markel

This report summarizes work performed under USBM Contract No. J0100047 revealing the performance characteristics of a composite-type resilient screen deck. The ability of the composite to perform or compete with steel in noise attenuation and longevity was of interest. Tests were conducted at the River King Preparation Plant of Peabody Coal Company. This facility was chosen because it provided parallel process flow and met standard coal cleaning requirements. Comparisons could be made between the adjacent resilient and steel screen decks under similar operating conditions. Noise reductions of 1-6 dBA were realized in the near field. Although the test period did not determine resilient screen life, indications are favorable for their longevity.

Jan 1, 1981

By M. M. Tilman

As part of ongoing research to improve mine safety, the Bureau of Mines conducted research on the corrosion of friction rock stabilizer steels in five Missouri lead and iron mine waters. Electrochemical corrosion tests, including evaluation of pitting tendency, were performed on two types of high-strength, low-alloy (HSLA) steels and galvanized steel in four Missouri lead mine waters and one Missouri iron mine water. The tests were conducted at in-mine water temperatures in both air-saturated and deaerated waters. Static, weight-loss corrosion tests were also conducted on HSLA steel specimens in the five Missouri mine waters for 2,900-h duration at average in-mine water temperatures and air-dissolved oxygen contents of 6 to 7 ppm. Corrosion rates determined by the weight-loss tests were roughly comparable with rates determined electrochemically in deaerated waters containing 0.3 to 0.5 ppm dissolved oxygen content. Passivation of specimen (nongalvanized) surfaces in air-saturated waters resulted in very low electrochemically deter- mined corrosion rates. Pitting-tendency was generally higher for both HSLA steels in air-saturated waters than in deaerated waters. Galvanized steel generally exhibited higher tendency to pitting in the deaerated waters than in the aerated mine waters.

Jan 1, 1985

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By Eugene O. Binyon

"Belt and shaker conveyors, used singly or as combined units, have for many years been an integral part of many coal-mine haulage systems. The belt conveyor has also been used extensively as a main haulage unit in open-pit iron-ore mines of the Lake Superior district, particularly on the Mesabi Range. Few underground metal mines, however, either in the ferrous or non-ferrous branches of the mining industry, use the conveyors exclusively or even extensively for underground haulage. At present, only five iron-ore mines in the entire Lake Superior district have belt- or shaker-conveyor installations of any significant size. Of these mines, three are in the Crystal Falls-Iron River district of Michigan on the Menominee Range, one is on the Marquette Range near Ishpeming, Mich., and one is on the Mesabi Range near Keewatin, Minn.Results of the studies of tackless haulage in the Lake Superior district will not permit the establishment of any formula to prove or disprove the advantages of belt or shaker systems at all underground mines. The studies do show that trackless haulage can be used to advantage where the proper conditions exist. Advantages are particularly apparent when development can be planned sufficiently in advance of exploitation to permit installation of belts or shakers as part of the development program and where the systems are extended to include haulage in stopes as well as main entries.During the winter of 1947-48, the Bureau undertook a study of all of the underground ore conveying systems known to be in operation in the Lake Superior district for the purpose of making available to the entire mining industry the technologic data developed in the area. Because conditions that led to the installation of the belt and shaker conveying systems were often a function of the character of the deposit or the method of mining, a brief description of those conditions is included in this report.After a preliminary investigation into the extent to which trackless conveyors were employed in the district, it was found that a detailed study at five bites would result in fair appraisal of that method of haulage in the underground iron-ore mines.Each of the five significant installations is described separately in this report. In one instance, however, company policy does not permit identification of the mine wherein the conveying is done. In that instance the operation is designated as mine ""A"".Unless otherwise specified, all tonnage figures quoted herein are gross.The cooperation of officials of all of the companies operating underground mines in the Lake Superior district permitted successful completion of preliminary studies of mining practices and conveying systems.Special acknowledgment is made to R. D. Satterley, general superintendent, and to operating staffs of the Sherwood and Morris mines of the Inland Steel Co. The assistance given by W. D. Whitman, assistant superintendent, and Douglas Tippett, mine captain at the Morris mine, and P. D. Pearson, superintendent, R. O. Marsten, engineer, and W. Johnson, mine captain, at the Sherwood mine, is acknowledged."

Oct 1, 1949

By Alfred L. Ransome

GOLD output in Alaska in 1950, following a 2-year decline, increased to the highest point since 1942. Tills unexpected gain in production of the Territory's greatest value commodity was largely responsible for the increase in the over-all value of mineral output in the Territory to $17,852,000 from $15,549,000 in 1949. Although coal continued to rank second to gold in value of output, production was slightly less than the record production of 1949. The mining of platinum continued to be an important factor in the mineral industry, with production of crude platinum metals exceeding that of 1949. The output of lead was three times the 1949 production, and silver gained 46 percent over the previous year's total. Copper and zinc production-entirely as byproducts from other ores-showed an increase, but remained minor. Production of tin was relatively small, but substantially above the total for 1949.

Jan 1, 1953

By S. Benedict Levin

In the spring of 1944, during the emergency In the supply of strategic mica, the Bureau core-drilled six aggregating 913 feet, at the Blister mica Trim. Cheshire County, N.H. These holes indicated a downward extension or the mica shoot which was being mined at that time and developed information essential for economic mining of the deposit.

Jan 1, 1949