Search Documents

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By N. S. Raymon

As part of an interegency agreement with the Energy Research end Development Administration to develop unproved refractory materials for use in coal gasification processes, the Bureau of Mines reviewed the literature to determine the effect of steam, H2, CO, and CH4 as well as the alkali metal oxides K2O and Na2O on refractory materials. Emphasis was given to the performance of high-alumina castable and fired refractories to conditions expected in coal gasification processes. Approximately 85 references were reviewed with 40 cited in the text. The literature was found to contain little data directly applicable to the selection of refractory lining materials suitable for use under the conditions of temperature, pressure, and gas compositions expected in second generation coal gasification reactors.

Jan 1, 1976

By W. W. Odell

"It is common knowledge that extensive lignite deposits occur in the States of Montana, North and South Dakota and Texas. The total area of these deposits and the total amount of lignite in them is so great that the true economic value of lignite is seldom realized. These deposits underlie areas of thousands of square miles. The area of the lignite lands in North Dakota alone is estimated to be approximately 32,000 square miles. Nearly one-third of the total solid-fuel resources of the United States is lignite and approximately 90 per cent of this lies in the Northwest.To the people of the Northwest the more extended utilization of lignite is of fundamental importance, hence any methods for commercially producing salable products from lignite that promise further development of these great fields deserve careful study.The development of our lignite resources has been slow, partly because the districts wherein lignite is found is not thickly settled or highly developed in manufacturing industries, but also because of the physical and chemical characteristics of the lignite. Lignite is classed as a low-grade fuel and may be con¬sidered as imperfectly developed coal -which has a more or less woody structure; it may be of the brown-coal type or darker, denser and more homogeneous, approaching subbituminous coal in character. As mined it contains more than 30 per cent of moisture exclusive of the -rater of decomposition formed .then it is carbonized or burned. The heating value as determined by the calorimeter is approximately half that of good quality bituminous coal. Upon exposure to the air lignite loses part of its moisture, whereupon the lumps chock and split until after considerable exposure, a large percentage of slack is formed. It cannot be stored in large piles so successfully as come other fuels, and it some instances it is more apt to ignite spontaneously in storage or in transit then the higher grade fuels."

Feb 1, 1924

By A. C. Richardson, G. D. Coe, B. M. Bird

"The Hull mine of the De'Bardeleben Coal Corporation is located in the Warrior field, in Walker County, Ala., about 25 miles northwest of Birmingham. The Mary Lee bed at this point is coking coal and has been used in the manufacture of by-product coke, but at present it is sold exclusively as a domestic and locomotive fuel.The data in this paper, which is the third in a series on the washability of Alabama coals,5 have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. The paper contains screen-sizing and float-and.-sink tests of a representative sample of run-of-mine coal, and flakiness tests and crushing tests of certain sizes.In addition, complete analyses of the ¾-inch to 3/16-inch size, raw coal, together with ash fusibility tests of the float-and-sink fractions have been made; those results are given in Tables 1 and 2. Since they indicate that the pr ration problem, like that at Lewisburg, Ala., is one of ash reduction, the further tests and the discussion have been restricted to that subject."

Apr 1, 1931

By J. B. Ligon

Blast induced stress waves, propagating along the surface of a drift of an underground hardrock mine, were recorded and analyzed. Resistance strain gages, accelerometers and a velocity pickup were used in making the measurements. Although a full face blast was recorded, the stress waves were initiated by single borehole blasts for the majority of the project. A special instrument trailer was designed, constructed and utilized during the project. A reliable strain wave transducer was developed for measuring the stress waves propagating on the drift surface. A correlation study between strain and acceleration signals for P-waves was made which agreed well with theory. The use of stemming was found to reduce strain and acceleration magnitudes as predicted.

Jan 1, 2011

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994

By Hillary W. St. Clair

Mining activity began in colonial times with ironmaking operations scattered along the eastern seaboard. Iron furnaces and forges manufactured iron implements from bog iron ores using charcoal from the extensive forests as a fuel. Lead ores were mined in the Mississippi Valley and copper ores in the Lake Superior region. However, the real beginning of the American mining industry did not occur until the 19th century. The history of American mining is organized around three epochal events. The first was the discovery of gold in California in 1848, which marked the beginning of a period of apprenticeship in mining and metallurgical techniques. The second was the discovery of the fabulous Comstock Lode in western Nevada in 1859, which expanded mining throughout the Far West and led to large-scale underground mining and the development of smelting techniques for lead, silver, and copper ores. The third event was the building of a transcontinental rail-road system after the Civil War, which brought about the consolidation of the industry from a large number of independent mines, mills, and smelters into integrated operations run by large corporations. Thus developed the mining industry that today supplies the energy and critical materials for the great-est industrial complex the world has known.

Jan 1, 1977

By James S. Wroth

The Act of Congress approved June 25, 1926 (Public Act 424, 69th Congress), authorized joint investigations by the U. S. Geological Survey and the U. S. Bureau of Mines to determine "the location, extent, and mode of occurrence of potash deposits in the United States." The particular deposits selected for exploration were the extensive rock-salt formations underlying large areas in western Texas and southeastern New Mexico, from which potash salts had been identified in the cuttings and sludges from oil wells drilled with cable tools. The evidence of these sludge samples was qualitative only and beyond definitely proving the presence of potash salts in the salt beds, gave little clue to the possible size, richness, or extent of the potash occurrences.

Jan 1, 1929

By E. G. Davis

Large-scale ultrafine grinding tests of a coarse kaolin were made using the Bureau of Mines developed attrition grinding process in continuous open-and closed-circuit systems. A 20-inch diameter attrition grinder, designed and constructed at the Tuscaloosa Laboratory, was used. Studies included single- and multiple-stage open-circuit grinding, and also continuous grinding tests in closed-circuit with a 6-inch-diameter solid bowl centrifuge. Clay feed, containing 9.0 percent minus-2-micrometer esd, was used at fates up to 840 pounds per hour. Multistage grinding tests gave better results than single-stage treatment when equivalent clay feed rates were used. Closed-circuit grinding tests yielded ground products containing slightly more minus-2-micrometer-esd clay than the open-circuit grinding when using the same clay feed. Energy consumption was lower in closed-circuit grinding than in batch or open-circuit grinding. A modified two-stage closed-circuit grinding system gave the best grade of product and amount of minus -2-micrometer-esd clay produced per pound of clay feed. The ground product from this test contained 88.5 percent minus-2-micrometer-esd material and electrical energy consumption was 327 kilowatt-hours per ton of minus-2-micrometer-esd material produced.

Jan 1, 1973

By C. M. Paiencia

The Bureau of Mines studied the potential availability of primary antimony (Sb) from demonstrated resources in 21 mines and deposits in market economy countries (MEC's). Twelve of these properties were evaluated as producers and nine as non- producers. The 21 studied properties contain 499,600 mt Sb as demonstrated resources, of which 304,000 mt is recoverable as antimony metal; another 973,500 mt Sb is contained in inferred resources. Recoverable antimony from demonstrated U.S. deposits is only 10,700 mt, just 3.5 pct of the MEC total. Domestic production of primary antimony from operating mines has averaged only 561 mt/yr over the 10-yr period 1975-84. This represents just over 5 pct of total U.S. consumption of primary antimony, which averaged 11,081 mt/yr during the same period. The United States will thus continue to rely on imported ores andlor concentrates, antimony oxides, and metal to satisfy domestic industrial requirements. At production costs up to $1.15/lb Sb, 110,000 mt of refined antimony is potentially available from 10 of the 21 studied properties. At $2/lb, 294,000 mt Sb is available, and at $3/lb, the total rises to 304,000 mt Sb available from all evaluated producers of refined antimony.

Jan 1, 1986

By R. W. Watson

In January 1980, the Bureau of Mines initiated an experimental program to examine the fire and explosion hazards of one-hour self-contained self rescuers (SSRs). This action was prompted by a growing concern on the part of government and industrial safety officials over the potential hazards of these devices when deployed on a large scale in underground coal mines. Prior evaluation of the safety of these devices had been at best sporadic and usually limited to experimental models. The recent availability of preproduction models of a l-hour SSR fabricated by the Mine Safety Appliance Company* and a production model manufactured by Dragerwerk Ag Lubeck of the Federal Republic of Germany allowed for a more comprehensive and meaningful evaluation of their safety in underground coal mines. This report summarizes the results of a 5-month study of the potential hazards of these two items. During the course of the work, periodic progress reports were presented to officials of the Mine Safety and Health Administration and various mining organizations including the American Mining Congress, Bituminous Coal Operators of America. National Independent Coal Operators Association, and the United Mine Workers of America. The free exchange of ideas that occurred during these meetings had a significant impact on the direction of this study and a serious attempt was made to address all of the issues that were raised at these meetings. The authors are extremely grateful to the individuals that participated in defining the specific problems that could arise as a result of deploying the self-contained self rescuers in an underground coal mine environment.

Jan 1, 1980

By R. G. Knickerbocker, A. L. Fox, J. Koster, P. R. Perry

"During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report. 6/ The geology of the Marysvale region has been reviewed recently. 7/The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.The preliminary work just mentioned had given indications of the separation of sulphate salts high in potassium from fusions of alunite with borax glass.During the course of further work along those lines, fusions of boric acid and alunite were tried. No separation of salts was obtained, but it was observed that rather complete removal of so3 from the alunite occurred and that the sinter could be leached with water to give a solution contain¬ing most of the potash and a residue containing most of the alumina. The reaction that takes place can probably be written 8/:"

Mar 1, 1939

By Seth T. Reese

THE INJURY DATA and experience at coke ovens in the United States for 1952 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, frequency rates, and accident agencies involved in causing injuries. Data are given for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data in the coking industry covering 5- and 10-year periods on the number of injuries, accident agencies, and severity of injuries. (C) Historic injury experience: Tables 16 to 19: Contain data on the number of injuries, frequency rates, and employment at coke ovens from the earliest records through 1952, Operating statistics from 1929 through 1952 are given in table 19.

Jan 1, 1955

By L. B. Pankratz

Thermodynamic data on carbides, nitrides, and other selected substances were reviewed, evaluated, and compiled at the U.S. Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, -(G° - H298)/T, ?Hf, ?Gf, and log Kf are given in tabular form. Cp°, H° - H°248, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1994

By I. F. Avery

The productive capacity of natural-gasoline and cycling plants in the United States on January 1, 1958, was 48.8 million gallons per day, according to the Bureau of Mines biennial survey. This represented an increase of 2.4 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 7.5 million gallons per day. The major increase in operating capacity occurred in Texas and New Mexico. In New Mexico, capacity increased 43 percent. The total number of plants decreased from 600 on January 1, 1956, to 584 on January 1, 1958. The number of operating plants decreased from 571 to 558. Five new plants were completed in Colorado, increasing the number of operating plants from 7 to 12.

Jan 1, 1958

By James H. Russell

Alkalized alumina (an active form of sodium aluminate) has been considered as a sorbent for the removal of sulfur dioxide from industrial flue gases. Four rate equations, each based on a different mechanism, were compared with the results of thin-bed sorption tests. It was found that each equation agreed with the experimental results, within experimental variance, over most of the range of sorption studied. First-order rate equations were generally satisfactory in explaining both sorption and regeneration. It is concluded that the equations developed are adequate for the design of commercial fluidized beds for the sorption of SO2 from industrial flue gases and regeneration of the alkalized alumina.

Jan 1, 1970

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

By H. F. Weaver

The 17th National First-Aid and Mine Rescue Contest was held in the Kentucky Fair and Exposition Center, Louisville, Ky., October 2, 3, and 4, 1957. The meet was under the auspices of the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with the National Coal Association, United Mine Workers of America, State mining departments, local mining institutes, and coal operators' associations. The Arrangements Committee, as authorized by the General Committee, made all the necessary arrangements for conducting the 1957 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1958

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By J. P. Connell

The U.S. Bureau of Mines awarded a contract to Morrison-Knudsen, Inc., to evaluate the use of roadheaders in underground mining operations. Road-headers were found to be widely used in mines as construction support units, as development miners, and as stoping machines. However, road-headers were found to have mechanical and electrical problems, to suffer reduced productivity when integrated into the mining cycle, and to create dust problems. Also high capital costs and low utilization and avail-ability cause high amortization costs per ton. This report identifies the roadheader operating problems and offers suggestions for improved mechanical and electrical design as well as manufacturer and owner responsibilities for improved availability. The development of a complex integrated excavation and ground support sys tern is no t warranted until the roadheader itself is made much more reliable.

Jan 1, 1980