Search Documents

By F. O. Milovich, V. A. Ignatkina, L. A. Samatova, E. D. Shepeta

"The aim of the research was to increase technological parameters of the flotation of finely disseminated scheelitecarbonate ore using selective reagent regime.In the studies the monomineral fractions of scheelite and calcite; samples of the scheelite-carbonate ore of the Primorsky deposit with the range of the carbonate module 3-65 were used. A carbonate module of ore is the ratio an initial assay of calcite to an initial assay of scheelite. Sodium oleate, iso-decyl alcohol, water glass, calcium chloride, soda or sodium hydroxide as flotation reagents were used. The flotation method in the Hallimond tube and in a mechanical cell, an adsorption method for study the kinetics of adsorption of oleate and isodecyl alcohol and its combinations on scheelite and calcite, IR spectroscopy including ATR to study the composition of surfacecompounds were applied. Selective reagent regime may include two ways - a combination of collectors or a modification of depressants of calcite and other gangue minerals. On one hand the combination of sodium oleate and higher fatty iso-alcohols of fractions C12-C16 in the rough scheelite flotation to reduce the flotation activity of calcite has been studied. On the other hand depression of calcite flotation by calcium chloride with water glass into rough flotation was used; modified the steaming cycle by Petrov's method applying change the concentration of water glass and other. Fatty iso-alcohols can adsorb on the surface of the calcite that reducing the adsorption of sodium oleate and floatability of calcite has been fallen. Their co-adsorbing with oleat on the scheelite surface were support the hydrophobization and flocculation of slime particles of scheelite. Flocculation of the particles of scheelite leads to increased up 3 times of the recovery of scheelite from the slime class, and calcite change up only 1.4-1.1 times it’s recovery.The growth of the carbonate module more than 11 is decreased the assay of WO3 in the scheelite concentrate of selection cycle."

Jan 1, 2018

By M. M. Fan

In Florida?s phosphate industrial practice, the most favorable upper size limit of froth flotation is 1.18 mm which corresponds to particle weight of about 2.8 mg. Conventional froth flotation is not efficient in upgrading coarse particles (+0.425-1.18 mm). A limited number of studies have been devoted to understanding and improving coarse particle flotation. We have shown that the coarse particle flotation performance can be significantly improved by the presence of picobubbles generated by hydrodynamic cavitation. In this study, the size of picobubbles produced under certain hydrodynamic conditions was measured by a laser particle size analyzer. A size-by-size flotation performance analysis of coarse phosphate froth flotation in the presence of picobubbles is conducted in terms of flotation kinetics, selectivity and recovery. It was found that picobubbles doubled the flota-tion rate, increased the P2O5 recovery more significantly for +0.85-1.18 mm particles than +0.425- 0.6 mm and +0.60-0.85 mm particles. At a given acid insolubles (A.I.) rejection, the presence of picobubbles increased the P2O5 recovery by up to about 25%.

Jan 1, 2014

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By Y. Q. He

The methodology of active pulsing air separation is a new method for dry material classification. Especially, it is suitable to electronic scraps disposal and re-utilization. By studying the difference of drag coefficients of the particles moving through areas of varying Reynolds numbers, and considering the extra-mass forces acting on the particles in the active pulsing air field, models of the dynamic motion which particles follow were developed. A computer simulation was prepared that showed the traces of particles with different densities and/or diameters, but similar aerodynamic characteristics, as they moved through the turbulent flow, to modify and define the parameters of the models. The simulation was found to predict the observed results with artificial tracing spheres being separated by the laboratory equipment. The separation performance, as being affected by the particles, nature, the air velocity, the pulsing frequency and the air pattern, is discussed. In general, lower density particles are more responsive to variations in airflow velocity. In addition, an industrial scale active pulsing air separator was designed, and it provides a new and efficient method for resource re-utilization in China.

Jan 1, 2014

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

Results of flotation process combined with atmospheric leaching and high pressure leaching for recovery of copper from low-grade silicate-copper ore have been presented in this study. The low-grade copper ore contains a small amount of copper (0.42 mass %), iron (4.6 mass %), and silicon (38.3 mass%) and among many other metals (Al, Ca, K, Mg, Na, Ti and S). The main mineralogical constituents of the copper ore are calcium aluminosilicate (Ca(Al2Si2O8), amesite (Mg2Al2SiO5(OH)4) and gypsum (CaSO4×H2O), and quartz (SiO2) as resulted from the alteration of an igneous rock. This study has shown that about 92 % of copper can be recovered with a maximum copper grade of 4.2 mass% in a froth after 15 minutes of flotation at pH 8.5 when used potassium amyl xanthate as a collector, MIBC and Dow-froth 250 as frothers and calcium hydroxide as a pH adjuster. The images of bubbles in the cell during flotation process were recorded using a high-speed camera. The froth concentrate with average copper grade of 2.0 mass% was further processed by atmospheric leaching with a solution of sulphuric acid and hydrochloric acid, respectively and high pressure leaching with sulphuric acid solution. As a result, leaching rate of copper reached about 60 % in an atmospheric leaching with sulphuric and hydrochloric acid respectively, whereas the rate can reach more than 70 % by autoclave leaching at high pressure under the controlled condition. A process to recover of copper from its low-grade ore can be developed by optimization of flotation combined with acid leaching.

Jan 1, 2014

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

By Avishan Atrafi

Frothing behavior of surfactants originate from their preferential adsorption at the gas-solution interface. Different surfactants may demonstrate different adsorption behaviors depending on their molecular structure and surface activity. The quantity and rate of adsorption of surfactants at the gas- solution interface in flotation systems will certainly affect kinetics of reaction and fractionation of surfactant between bulk and foam phase and subsequently their frothing characteristics. In this paper, the frothing characteristics of sodium oleate which is the main constituent of fatty acids used in flotation systems is explained. The adsorption behavior of sodium oleate is then compared to a typical non-ionic frother (Methyl Isobutyl Carbinol, MIBC) in terms of different adsorption behavior at the gas-solution interface. Since long chain fatty acids are weak electrolytes, their behavior is a strong function of pH. Also semi soluble salts including apatite contain considerable amounts of ions like calcium in their lattice, so the effect of presence of ions on the frothing behavior of fatty acids requires an investigation. A mass balance on the surfactant transferred to the foam was solved to estimate the bubble surface area flux in foam, which explained how the adsorbed surfactant at gas-solution interface controls the bubble surface area flux at foam. Since sodium oleate adsorption at foam takes place gradually, frother concentration as a function of time was monitored by the total organic carbon measurement (TOC) to compare the surfactant uptake rate at different concentrations, pH and ionic strength. The surfactant concentration adsorbed within foam together with the value of adsorption density from the Gibbs adsorption, leads to the calculation of the surface area flux and prediction of average bubble size in the foam at a specific time frame. This value was compared at different concentrations of sodium oleate. Dynamic surface tension measurements were accompanied to explain the adsorption behavior, though finally equilibrium surface tension turns out to better explain the foamability characteristics. Keywords: flotation collectors, flotation froths, foams, fatty acids, adsorption behavior

Sep 1, 2012

By Anatoly F. Usov, Vyacheslav A. Tsukerman

"The Russian scientists have developed a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks ets.) - the Electric Pulse Discharge method of materials destruction (EPD). The detailed researches of a broad circle of problems connected to development EPD-disintegration of materials of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the means of electric pulse splitting and refinements of materials are developed, the technological efficiency of disintegration of industrial minerals estimated.One of the most important characteristics of the EPD-disintegration of ores is the high selectivity of destruction, which provides a large ratio of useful minerals' grains opening, and at the same time, it destroy them less. This ensures in the subsequent stages of beneficiation of ores considerable increase of the extraction and improving the quality of concentrates.The technological tests of various industrial minerals have shown a possibility the EPD-disintegration, as a process that provides the best efficiency of disclosure of useful minerals in all types of ores. Technological and economic efficiency of the method of ore beneficiation is the highest for difficult beneficiated ores with rather low extraction by existing methods. The increase of extraction in this case can reach several percents. As a rule, at a EPD-disintegration the disclosure of mineral grains happens in earlier stages of material comminution than at a mechanical comminution, and with less damage of products. This promotes a simplifying the process of ore preparation and for reducing the power consumption."

Jan 1, 2003

By Sebastian Fredes, Williams Calderon, Mauricio Toledo, Gonzalo Montes-Atenas

The influence of the temperature on leaching kinetics of copper-bearing minerals has been widely acknowledged: the leaching of copper oxide ores is generally described as exothermic reactions while copper sulfide ores are associated with endothermic reactions. Reports studying the influence of temperature on leaching kinetics at laboratory scale frequently involve the implementation of either fully flooded isothermal systems or jacketed column setups. Nevertheless, at industrial scale controlling or monitoring the temperature or temperature changes is almost impractical. In fact, leaching process is usually a large tonnage operation and changing the temperature of vast amounts of material would require an enormous amount of energy and highly specific heat transfer equipment. Preliminary computations on the amount of energy required to increase the temperature of a heap or dump in 1°C indicates that it would be impossible to find an energy source able to accomplish the task. In order to provide a solution to this matter it is suggested to create an energy managing protocol (EMP) that permits heat up or down the porous body locally taking advantage from the temperature gradients and from the reactivity of different regions within the material as a function of the leaching cycles. The aim of this study is to evaluate different heat transfer regimes in a 1 ton pilot column leach operation. It was found that best results of copper recovery are obtained when heating up the column in horizontal bands starting from the top of the column moving downwards as the leach cycle evolves. The system is expected to be suitable for industrial applications, but further development of the technique is required, particularly in the design of the heat transfer dispositive.

Jan 1, 2014

By Isaak I. Maksimov, Tatyana E. Koltunova, Mikhail F. Yemelyanov, Liudmila A. Otrozhdyonnova

"INTRODUCTIONMetals losses amount up to 50% in coarse fractions in (>100 µm) and composite particles, and to 20- 25% in fine fractions (<10 µm) at non-ferrous floatation concentrating plants of the CIS. Therefore, reduction of metals losses in difficult fractions is of high significance.IMPROVEMENT OF FLOATABILITY OF COARSE AND COMPOSITE PARTICLESReagent regimes with application of strong collectors – xanthates ?5-?8, combination of butyl xanthates and aerofloats ?10-?12, butyl xanthates with hydrocarbons are proposed for this purpose. Application of such reagent regimes for copper and copper-molybdenum ores permitted to increase copper and molybdenum recovery by 0.5-3.9%.Studies, performed by means of specially designed non-frothing flotation machine with independently controlled agitation intensity and narrow size-ranges of air bubbles, established that the best results are achieved with employment of bubbles of 0.5-0.8 mm size regarding particles of any size, with small amounts of up to 2 mm size “transport” bubbles to be expediently used for floatation of coarse particles.Energy dissipation in the main volume of floatation cells must be lower than 0.2-0.25 m2/s3.Performed experiments permitted to formulate requirements to development of machine for floatation of coarse and composite particles. Such floatation machine with volume of 8.5 m3 provided for weak agitation in the main volume of floatation cell and uniform distribution of coarse particles throughout the depth owing to establishing of pulp circulation with upward flows. In addition, in the upper part of floatation cell where agitation is considerably weaker, favorable conditions are created for attachment of particles to bubbles. Testing of this floatation machine demonstrated a 7.5% increase in recovery of +0.2 mm particles in pyrite floatation and a 12-14% increase in recovery of +0.2 mm particles in apatite floatation as compared with a reference floatation machine."

Jan 1, 2003

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Barbara Peszko, Tadeusz Tumidajski

"Various methods are used to identify the grain composition of fine-grained materials because so far the best notion of the grain size has not found and there is no single method to define grain size. In practice the most important are the following grain sizes: sieve diameter dt, effective diameter de, substitute diameter d2 and statistical diameter dst. The mentioned sizes are connected with the methods of analyses. Methods are correct but measure of different diameters of grain and their results are different.The most important methods of granulometric composition analyses are the following: the sieve analysis, the sedimentation method and the conductometric (Coulter-Counter) methods. In each of these methods various physical features connected with the grain size are measured.Sizes of grains defined by different formulas or measurement methods are associated mutually by dependencies, which are results of differences in their determination or calculation ways.In order to determine principles of results comparison the classification analysis results on linearly or non-linearly connected was made. Analyses which results demonstrate the same type of grain size distribution are treated as linearly connected. It is based on the general formulae which determines the probability density function of random variable which is the function of another random variable having the known density function.In order to show the difference in the grain composition of the same material qualified by different methods, three methods of investigations were distinguished. They are: the sieve analysis performed on precise sieves, the sedimentation analysis performed by means of a sedimentation balance “Sartorius” and the microscopic analysis performed after preparing a microscopic slide where the grain size was measured by the Martin’s method.The materials selected for the analysis were quartzite and glass, which are the material of high purity.The obtained results of mentioned above three types of analyses were approximated by distribution function of four distributions: Weibull, log-normal, cut Weibull and Gaudin-Schuhman."

Jan 1, 2003

By Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Istanbul Technical University, Mustafa Tarkan

"Zeolites are naturally occurring as hydrated aluminosilicate minerals. They belong to the class of minerals known as “tectosilicates” and are related to the common minerals feldspar and quartz. Seven natural zeolites that occur in large, commercially exploitable deposits, are: clinoptilolite, chabazite, mordenite, phillipsite, erionite, analcite, and ferrierite. Among them, clinoptilolite is the most abundant one and is not the best known, but is one of the more useful natural zeolite. Clinoptilolite [(Na3K3) (Al6Si30O72) 24 H2O] is very closely related to heulandite and is currently being considered for disuse it self as it may just be a variety of heulandite. It differs from heulandite significantly only in its enrichment in potassium and slightly more silica and it is argued that a separate mineral is not needed.There are large zeolite deposits in western part of Turkey. The sample used in this study was taken from the Gördes region of these deposits. Screen, chemical, XRD and mineralogical analyses were used to determine properties of the natural zeolite sample used in this work.According to the size distribution of the sample, it is found that the zeolite sample used in this study is below 1 mm in size and almost 80% of it is below 0.5 mm. X-Ray Diffraction (XRD) and mineralogical analyses show that the natural zeolite is found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. XRD analysis also shows that the sample contains approximately 58-60% clinoptilolite, 5% quartz, 5% feldspar, 10% smectite, 5- 10% illite and mica and remaining volcanic tuffs. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals."

Jan 1, 2003

By A. Güney, G. Önal

"The tailings of the Bigadiç Colemanite Concentrator at the West of Turkey which contain 18 % B2O3 and 1.57 % SO3 are collected at the tailing dams near the Concentrator. In this research, it was aimed to obtain colemanite concentrates with a minimum content of 40 % B2O3 and a maximum 0.5 % SO3 from the tailings. At the experimental studies, decrepitation methods were systematically applied following attrition scrubbing and sizing. At the end of the tests, the best decrepitation result were described, at 500oC temperature for 15 min. duration, the final concentrate having 57.84 % B2O3, 0.44 % SO3 with 73 % recovery was obtained.Boron ores reserves of Turkey are about 2.5 billion tons and Turkey has the 63% share of the World’s boron reserves. The boron reserves are located at Eskisehir (Kirka), Kutahya (Emet), Balikesir (Bigadic) and Bursa (Kestelek) districts in Western Turkey. In 2002, the total amount of boron production of Turkey was about 1.4 million tons, which is 40 % of the World boron production.Bigadiç colemanite (Ca2B6O11. 5 H2O) ore with a content of 30-31 %B2O3 are concentrated by attrition tumbling and classification process. So the final concentrates with contents of 40 and 42 % B2O3 are obtained at the size fractions of –125+25mm and –25+ 3 mm respectively. The tailings materials with an 18 % B2O3 content are collected at the tailing dams near the Concentrator. In this research, it was aimed to obtain colemanite concentrates with a minimum content of 40 % B2O3 and a maximum 0.5 % SO3 from Bigadic tailings having 18 % B2O3 and 1.57 % SO3.In experimental tests, attrition scrubbing, wet sieving, gravity separation, electrostatic separation, flotation and decrepitation were adopted to the colemanite tailings, and optimum beneficiation conditions were obtained."

Jan 1, 2003