Search Documents

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By S. Liu

With the development of global economy, the demand of mineral?s quantity and quality are in-creased, valuable minerals are more and more finer and poorer, and the capacity of concentration plant are more and more high. Using large-scale flotation cells can obviously enhance the capacity of treating the mineral, reduce the cost, and increase the economic benefit and competitive ability for the enterprise. BGRIMM advanced advisable technical scheme with optimally parameter and route for the feature of dynamic in large scale flotation machine, and developed the KYF Large Scale Flotation Cells, which have used more than 400. The paper advanced the history, the design principle, the operating principle, the structure feature and the application of KYF flotation ma-chine.

Jan 1, 2014

By Xiaoping Xu

An albitization granite type tantalum-niobium ore from Jiangxi Province, China was taken as the research object in this paper. The main valuable minerals in this ore are tantalite-columbite and uranmicrolite, and the minerals that can be comprehensively recovered include cassiterite, sulfide minerals, topaz, zinnwaldite, and quartz-feldspar. Based on the research results of process mineralogy, the roughing process of gravity separation for coarse particles combined with flotation for fine particles is proposed. The combined cleaning process of flotation-gravity-magnetic-electric-hydrometallurgical separation is adopted for the rough concentrate of gravity separation while the combined cleaning process of gravity-flotation- hydrometallurgical separation is adopted for the rough concentrate of flotation. High intensity magnetic separation is used to separate and recover zinnwaldite and quartz-feldspar from gravity tailings. By mineral processing for the crude ore containing (TaNb)cassiterite concentrate is 0.0003% with a grade of Sn 63.22% and a recovery of Sn 47.42% while the yield of sulfide concentrate is 0.0783% with a grade of Pb 33.15% and Zn 27.09% which can be separated to get lead and zinc concentrate respectively. The yield of topaz concentrate is 0.1545% and the topaz mainly distributed in the size range of -0.4+0.074mm, which can be made into abrasive products of different particle sizes after classification. The yield of zinnwaldite concentrate is 16.91% with a grade of Liwhiteness of 75%, which is a glass-ceramic material of good quality. 2O5 0.0346%, Sn 0.04%, Pb 0.10% and Zn 0.33%, the tantalum-niobium concentrate with a yield of 0.00278%,a grade of (TaNb)2O5 53.61% and a recovery of (TaNb)2O5 44.49% is obtained. And the yield of 2O 1.34% and Rb2O 0.40%. The yield of quartz-feldspar concentrate is 30.42% with a grade of K2O+Na2O 8.98% and Fe2O3 0.11% and a natural All of tantalum, niobium, cassiterite, topaz, zinnwaldite, quartz, and feldspar are recovered effectively. Keywords: tantalum-niobium ore, gravity separation for coarse particles, flotation for fine particles, comprehensive recovery

Sep 1, 2012

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By M. L. Liu

This work reports the results about the determination of mean activity coefficients and relative partial molar free energies for copper sulfide mineral bioleaching solutions by potentiometric method at 25ºC. The experimental potentiometric data were obtained by combining a solid state membrane-cupric ion selective electrode (Cu2+ ISE), containing a KNO3 filling solution, and an Ag/AgCl electrode. The measurements were performed in different series of copper sulfide mineral bioleaching solutions. The non-ideal behavior of the system was described on the base of the Pitzer ion-interaction model for mixed salts. Meanwhile, the relative partial molar free energies of bioleaching solution were investigated. The determination of the thermodynamic properties offers a basic data for the study of copper sulfide mineral bioleaching solutions.

Jan 1, 2014

By P. Coghill, P. Revell

"Geo-sensing is the ability to routinely measure or infer rock properties at a range of scales using non-destructive scanning devices. These devices can provide information and data flows to support integrated decision making across the minerals value chain. Geo-sensing has been used for many years in minerals exploration using technologies such as satellite imaging and airborne geophysics but to date the use of sensing technologies in between the mine and mill has been very limited. The aim of this research is to develop new mineral sensing technologies that can enable grade engineered ore streams through the rejection of low value gangue or deleterious elements either in the pit or during transfer to the mill. This paper focusses on the research and development being carried out by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and its associated members on new sensing technologies. At the start of their development these technologies were classified on the Technology Readiness Level scale at 3 (TRL3), equivalent to a proof of concept. Laboratory testing and design is aimed at progressing these sensing technologies to TRL5 which is ready for testing at an end users site. New data obtained during the laboratory testing and design phases are presented in the paper demonstrating performance specifications such as detection limits and measurement speed which can be used to infer the pod size of gangue that can be rejected at scale. Grade Engineering® and coarse gangue rejection are considered as key drivers for the mining industry to address the higher mining, processing and environmental costs associated with ore bodies with declining grades. This is an industry wide problem and the development of mineral sensors is seen as key enabling technologies for Grade Engineering® and coarse gangue rejection. The technologies presented in this paper enhance value through early decision making of ore quality and improve the overall resource value case through improved grade and throughput engineering."

Jan 1, 2018

By Jim Pae Lem

This study investigates the mode of occurrence of uranium in a copper concentrate from the Prominent Hill mine. Mineralogical and liberation studies of a high grade Cu concentrate (monthly composite) containing uranium (U) were undertaken using QEM-Scan in combination with QXRD and ICP-MS. The study aimed at determining in what form U was recovered, and by which mechanisms. The deportment of U was studied in 3 size fractions; +20µm, -20+8µm and -8µm. QEM-Scan analysis showed that uranium was present as U(Cu)-silicates, U-silicates, UPbOx/FeOx or traces of UThOx and UTiOx, with the U-silicates present across the size fractions. The association of uranium bearing minerals with copper sulphides varied across the size ranges. Interestingly, most of the U (46% by weight) was distributed in the finest fraction (-8µm), in which the deportment of Cu was low (6%). Over 40% of the U mineralisation in the -8µm was liberated. In terms of the floatation response, while recovery of the uranium minerals as a result of their association with copper sulphides (as composite particles) was evident, recovery of UPbOx locked in hydrophilic haematite in the +20µm size fraction suggests, that other mechanisms (e.g. Inadvertent activation by Pb from radioactive U decay) are possible. Furthermore, the high amount of fine liberated U bearing particles in the concentrate points at entrainment as another major mechanism for uranium recovery, and therefore, a target for process optimisation.

Sep 1, 2012

By C. V. G. K. Murty

Sillimanite, chemically named Aluminum silicate, 3Al2O3SiO2 is one of the three forms of alumino silicate polymorphs and commonly encountered in aluminous metamorphic, plutonic, and volcanic rocks and their weathering products. Most of the sillimanite deposits are granular and are of high grade available in coastal areas as associated mineral along with Titanium bearing minerals namely ilmenite, rutile etc. Sillimanite is one of the widely accepted raw materials for the manufacture of high alumina refractories (55-60 % alumina) or bricks. Sillimanite based refractory bricks are used for the lining of Blast furnaces, Arc furnaces, Soaking pits, Reheating furnaces of iron and steel, rotary kilns for cement manufacturing and general kilns for lime production. Considering the vast potential of unexploited sillimanite reserves in India, M/s Trimex Sands Pvt. Ltd., (TSPL)has set up a Mineral Sand Processing plant in 2010 at Andhra Pradesh with a capacity to produce about 50,000 tons of sillimanite per annum besides the production of various heavy minerals such as ilmenite, rutile, zircon and garnet. Traditionally in India, sillimanite is upgraded by froth flotation technique using Oleic acid as a collector cum frother, sodium silicate as depressant and soda ash as pH regulator. At TSPL, Conventional mechanical float cells are installed to float sillimanite. In addition to the usual problems associated with conventional cells, poor flow ability of the sillimanite concentrate is experienced in dry circuit due to the presence of sodium oleate. Fine garnet in the sillimanite concentrate contributes to high iron content in the final product, making sillimanite separation a nightmare for operators (lower recoveries coupled with inferior grades). Various efforts were made to improve the performance of the circuit such as introduction of additional frother like MIBC, optimizing the operating parameters such as pulp density, collector dosage, depressant dosage, air flow rate, pH etc., use of collector aids, stage wise addition of reagents etc. The challenges faced to produce a sillimanite product with stringent quality norms and the efforts made to improve the grade and recovery are described in this paper. Keywords: sillimanite, froth flotation, conventional mechanical cell

Sep 1, 2012

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By Abhakumari

Effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. Effect of the magnitude of electrolytic currents on the activity and growth of bacterial cells was studied. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and bio catalysis of anodic oxidation.

Sep 1, 2012

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci, A. Zucca

"Beneficiation of the epithermal gold mineralizations associated with an extensive alteration zone in the Serrenti-Furtei region on the island of Sardinia, is proving a complex issue. Experimental investigations have in fact demonstrated that while the ores contained in the upper parts of the deposit are amenable to conventional cyanidation, the gold contained in the refractory ores in the lower portions needs to be recovered by means of flotation, combined with leaching where necessary.The results of commercial heap leaching, carbon-in-leach (CIL) processing and flotation, designed on the basis of the experimental findings and applied to the oxidized portions and transition zones of the deep sulphide mineralizations, confirmed the expectations emerging from the laboratory tests."

Jan 1, 2003

By Leopoldo Gutierrez

Eight oil sand ores with the bitumen content ranging between 3.6 and 15 wt.% and the fines content (-44 micrometers size fraction) between 9 and 69 vol.% were subjected to the standard alkali extraction test used to measure the degree of oxidation of metallurgical coals. The results showed that there is a strong correlation between the absorbance of extracted solutions at a wavelength of 520 nm and the ratio of the fines content to the bitumen content. The latter factor is directly relevant to assessing the extractability of bitumen from oil sand ores. Bitumen extraction tests showed that the bitumen recovery decreased from 90 % to 30 % when the absorbance at 520 nm increased from 0.23 to 0.64. A comparison of the UV/visible spectra of solutions obtained from the alkali extraction tests with solutions of Aldrich Humic Acids suggest that low bitumen/high fines oil sand ores release substantial amounts of organic matter very similar, if not identical, to humic acids. In contrast, high-bitumen and low-fines ores do not release as much of the organic matter, and UV spectra of these leached substances are quite different from those of humic acids. Overall, the results show that chemical composition of bitumen in the tested ores varies greatly with ore type and oxidation, and that the alkali extraction test is a promising technique to quickly assess the extractability of bitumen from a given ore type.

Sep 1, 2012

By Kari Niiranen

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. The largest of the apatite magnetite deposits and the mines are Kiirunavaara with annual production rate of approximately 27 Mt crude ore underground. LKAB produces two varieties of pellets: blast furnace pellets and direct reduction pellets (LKAB DR Oxide Pellets). Meanwhile the concentration process in a sequence of the low intensity magnetic separation (LIMS) and flotation at the concentration plant. In spring 2007 there were noticed great fluctuations of SiO2 grade in the crude ore. The high SiO2 grade is particularly problematic in the case of direct reduction pellets. In consequence, a project was started (called Silica in the Mine) to define exactly the problem related with silica and to find out, if possible, the reason for the great fluctuation of SiO2 grade in the crude ore going to the processing plant. A further target of this project was to develop a simplified method at the laboratory scale, to predict SiO2 grade in the magnetite concentrate in the future, but also predict the physical properties of the ore with respect to mineral processing. The essential stage of systematic characterization of the ore body for mineral processing properties is the estimation and simulation of different parameters from the laboratory scale to the large scale at the concentration plants using empirical data collected at the mineral processing by LKAB in Kiruna. Further a target was also to find useful physical parameters for mineral processing and implant those parameters into the existing geological 3D-model of the deposit. This information will be used for making prognosis of the future mining and the quality of the crude ore. It will also give better control and improve the production planning in the mine and the performance at the concentration plant in Kiruna concerning the decrease of the SiO2 grade of the magnetite concentrate.

Sep 1, 2012