Search Documents

By Y. M. Fu

In order to evaluate the flotation process, the process flow sheet was investigated. The process mineralogy of main products was studied. Through chemical mineralogical and screening analysis as well as surveying using a microscope and scanning electro-microscope, the oxidation degree and mineral composition of main-products the liberation of main minerals, the occurrence of elements such as Pb, Zn were revealed. It is pointed that to determine the flotation process, the type of prod-ucts optimum grind of original ore and middling was provided on the basis of liberation of main minerals is reliable. As correct finer ground original ore, first high-grade lead-concentrates and zinc-concentrates fast was floated from a great part of free of the galena and sphalerite of liberated. Then for finely re-ground middling of locked mineral grains of difficult liberation, mixing lead-zinc-concentrates second was floated. The four products was best in contact with characteristic of ore of Fan Kou. Therefore be obtained certain to successful economic effect.

Jan 1, 2014

By J. H. Starkey

SAGDesignTM Testing for grinding mill design was introduced commercially in 2004. Up to January 2008, 18 projects have been completed and 99 samples have been tested using this method. Two papers have been published describing the patented test procedure and one of these shows how the results compare with other grinding test methods. This paper will briefly discuss the theory on which this technology is based, and explain the procedures used to develop the calibration equation. Case studies are also included to demonstrate the effectiveness of the test work being done. These case studies show how the SAGDesign test is being used today: to design new grinding circuits for commercial full scale use; to calculate throughput in existing mills for production planning; and to accurately define grinding mill requirements at the scoping, pre-feasibility or feasibility study stage of project development, in order to economically identify the size and cost of the grinding mills that will be needed for the project. This is important because if the full rec-ommended SAGDesign testing program is done at an early stage in the project, the definitive cost for a guaranteed throughput, grinding mill design (by Outotec if their mills are purchased) is available. New grinding mill design for final engineering will be represented by the test work done on the Climax Molybdenum Project for Phelps Dodge (now FMI) in Colorado, USA. The SAG mill and ball mill for Climax are now in fabrication with project start up in late 2009. Next, the sizing of grinding mills at the scoping, pre-feasibility or feasibility study stage of mine development will be represented by a large metal mining property in Russia. Finally, calculation of the throughput for existing mills will be represented by work done at a base metal mine, in eastern Canada. Test work for designing SAG mills is now done in four laboratories at the time this paper was written. One in the USA at Dawson Metallurgical Laboratories, Inc. in Salt Lake City, two in Russia at the TOMS Research and Design Institute and at the Irgiredmet Research Institute, both in Irkutsk, and a fourth mill has been installed in Australia at AMMTEC Limited?s lab in Perth. A fifth SAGDesign test mill for radioactive ores has been built by Starkey & Associates, specifically for testing uranium ores and can be moved to any licensed lab in the world on a project basis.

Jan 1, 2014

By J. S. S. Allwin Ebinesar

The bioremediation of zinc was carried out using Pseudomonas alcaligenes, a Gram negative heterotroph. The parameters such as pH, bacterial cell number, initial metal concentration, and interaction time on the biosorption of zinc were studied. The maximum zinc uptake was found to be about 95% at pH 5 and biomass loading of 2.7x1010cells/mL. The biosorption isotherm for zinc exhibited Langmuirian behavior and the Gibbs free energy of biosorption was determined to be -31.2 kJ/mol, indicative of coordination of zinc with the functional groups on the bacterial surface. The adsorption kinetics followed a pseudo-second order equation. FTIR and EDAX studies confirmed the interaction of zinc with the biomass. The mechanisms of metal-microbe interactions are discussed.

Sep 1, 2012

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By Zoran S. Markovic

The extensive laboratory investigations were carried out in order to determinate behavior of sulphide and nonsulphide copper bearing particles during the flotation. The present ore sample were contained 0.55% Cu with 20.1% of nonsulphide copper in it and gangue material with higher contents of alumina about 19.07%. In this paper will be presented some results such as: effect of particle size, pH and applied collectors. The main goal was in application of collectors S-7518, as well as mixture of KEX and Z-96. Z-96 is a product from Chemical Industry Zupa Krusevac which was used as auxiliary collector in mixture with xanthates. The best results were done with this mixture in ratio KEX / Z-96 as 77/23 % in area of oxidized minerals flotation, but the collector S-7518 was achieved better results in sulphide mineral flotation. The S-7518 has better selectivity between copper minerals and pyrite comparing to mixture of KEX/Z-96 in mentioned optimal ratio. Flotation recovery and copper grade in concentrate were studied by flotation kinetics tests.

Sep 1, 2012

By E. Yigit

In the flotation process the physical factors such as agitation intensity air flow rate and pulp solid concentration are very important parameters affecting grades and recoveries of the products. The flotation tests were performed on the samples of Bigadic colemanite ore to investigate these factors at different agitation intensities ranging from 1000 rpm to 1400 rpm and air flow rates from 1000 cm3 ? min-1 to 2000 cm3 ? min-1 with 2 L and 4 L cells using Denver laboratory flotation machine. The tested collectors were Cytec Aero 825, Aero 848N and their mixtures. Agitation intensity and air flow rises resulted in more floated material although sometimes being not selective. These effects can be attributed to powerful collisions between air bubbles and mineral particles. The first observation was the effect of pulp solid concentration on the floatability of minerals, while the flotation in 2 L cell (0.125 g.L-1 solid concentration) at 1000 rpm (0.176 wattcm-3), and with 1000 cm3.min-1 air flow rate was possible, the flotation in 4 L cell (0.0625 g.L-1 solid concentration at 1000 rpm. (0.176 wattcm-3) and with 1000 cm3 ? min-1 air flow rate was not possible. However at 4 L cell after increasing agitation intensity to 1200 rpm (0.201 wattcm-3) keeping 1000 cm3 ? min-1 air flow rate, flotation was possible again. This shows that these factors such as agitation intensity have some critical role on flotation. Another interesting observation was on the selective effect of pulp solid concentration. In the flotation with 1 L cell at different agitation intensities, collector Aero 848N was selective against calcite, while in the flotation with 2 L cell at different agitation intensities the same collector Aero 848N was selective against colemanite.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By D. J. Hallbom

The ?yield plastic? rheological model describes the flow behaviour of a variety of non-settling suspensions, including many types of mineral slurry. The current paper presents the laminar flow relationship (pressure gradient vs. flow rate) for a yield plastic fluid flowing through a pipe or cylinder. Simplified algebraic equations, suitable for engineering purposes, are presented for yield plastic fluids with values of the scaling factor in the range that includes most industrially important slurries. The laminar pipe flow relationship is one of the most important fluids engineering calculations. It may be used to determine the rheological parameters of a material in a capillary rheometer or flow loop. If the rheology is known, these relationships may be used to determine the laminar flow pressure gradient in pipelines of various sizes.

Jan 1, 2014

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By Jianjun Tian, Changjiu Zhang, Chunmin Wang

Two lines of single stage autogenous milling circuits have been installed and commissioned as the primary grinding process for the Sino Iron project where magnetite ore is treated to produce iron concentrate via magnetic separation. Various challenges were encountered during the commissioning and ramp up stages which are discussed in the paper and include treating a highly competent ore in a closed circuit AG mill, operating the largest mills in the world and dealing with a number of engineering issues related to plant operability. Details of how these challenges were overcome are described as well as the observed operating characteristics of the mills and their optimisation through rigorous study, simulation and successful solution implementation. Further potential improvement opportunities are also discussed as part of the ongoing technical program at site.

Jan 1, 2014

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

It has been fairly well established by many experiments that Thiobacillus ferrooxidans (T. ferrooxidans), also named Acidithiobacillus ferrooxidans(Kelly and Wood, 2000),can depress the floatability of pyrite. However, the mechanisms governing the process have not been known completely. In the present investigation, wettability and electrokinetic studies were carried out to examine the surface chemical changes on pyrite before and after interaction with T. ferrooxidans or its secretions. Attachment of T. ferrooxidans to pyrite was observed using a scanning electron microscope. The results of experiments showed that, under certain conditions, T. ferrooxidans and its secretions would obviously change the surface electricity of pyrite and result in the iso-electric point of pyrite shifting notably. However, the surface wettability of pyrite hardly changed and its hydrophobicity increased little after interaction with T. ferrooxidans and its secretions. Based on the results of the present investigation it can be reasoned that the depression of floatability of pyrite is due to the reduction of surface free energy, rather than the increase of surface hydrophilicity of pyrite. The decrease of surface free energy weakens the attachment of collector to pyrite; during the process bacterial protein plays the most important role and the bacterial chemotaxis strengthens the effect.

Jan 1, 2003

In this study, selective flocculating of diaspore using anion macromolecular reagent as flocculant was tested to separate diaspore from alum-silicate minerals. Firstly, the effect of pH on settling behavior of diaspore and kaolinite dispersions has been investigated. The results show that the maximum settling speed of diaspore and kaolinite appeared re-spectively at pH7 and pH3.33 which is close to the point of zero charge (PZC) of diaspore (6.8) and kaolinite(3.5). This result is in well agreement with the double electric layer theory. Secondly, the settling behavior of diaspore and kaolinite particles in different anion flocculant solution have been researched. The results indicate that flocculant solution concentration significantly affect the selectivity and the flocculating performance of anion molecular. In high concentration solution, both diaspore and kaolinite have faster settling rate compared to blank solution. How-ever, in low concentration solution, the anion macromolecular can enhance the settling rate of diaspore remarkably but has no apparent effect on the settling rate of kaolinite. This result suggests that the tested anion flocculant is a promising reagent for de-silica of diasporic bauxite. Lastly, FTIR method was employed to probe the adsorption mechanism of flocculant on diaspore and kaolinite. The results reveal that there are anion flocculant characteristic bands on the spectra of diaspore but no obvious characteristic bands of flocculant on the FTIR spectrum of kaolinite. This result is in good correspondence with settling test.

Jan 1, 2014

By M. Karamoozian

Modelling and optimisation of the power draw of large SAG mills are important due to the large power draw which modern mills require (5~10 MW). The cost of grinding is the single biggest cost within the entire process of mineral processing. Traditionally, modelling of the mill power draw has been done using empirical models. Although these models are reliable, they cannot model mills and operating conditions, which are not within the model database boundaries. Also, due to their static nature, the impact of the changing conditions on the power draw, within the mill, cannot be deter-mined using such models. Despite advances in computing power, on-line modelling of large plant scale mills could be a time consuming task. On the other hand, using on-line parameters for model-ling, result in more reliable control of SAG mill without performing any more costly tests. In this paper, SAG mill power draw is modelled using neural network approach. Six inputs, namely: solid percent, two bearing pressures, noise, recycle and feed rate were used to model the power draw. The produced model shows an acceptable correlation coefficient, R2 =0.9623.

Jan 1, 2014

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Automatic identification and characterisation of mineral raw materials and beneficiated products are of major importance in mineral processing. However, minerals show great variety in their composition and physical and chemical properties. Industrial minerals may contain the same elements in about the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. By means of EBSD, diagnostic mineral information can be achieved if indexible patterns are provided.Until now EBSD has not been used frequently on geological samples for mineral and micro structure discrimination.The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques."

Jan 1, 2003