Search Documents

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

By J. C. van Dyk

In a previous study by Van Dyk, et al., (2006) and Van Dyk et al. (2006), a FactSage model was developed to understand the chemistry and interpret mineral matter transformation during a fixed bed counter-current gasification process. It was concluded that the FactSage model developed, compared with HT-XRD experimental results and that the FactSage thermodynamic modeling sup-plies insight into specific mineral reactions and slag formation. The specific value for Sasol in using FactSage, in combination with HT-XRD is that it can be used to analyze equilibrium conditions for reactions occurring between inorganic and organic materials together, as well as to provide insight into mineral transformation and slag formation. The purpose of the present study was to improve the current FactSage modeling approach, by combining specific zones in the gasification process. This can improve and speed-up the interpretation of mineral matter transformations and flow properties of reacted mineral matter in coal and assist in identifying and quantifying slag formation in the gasifier operation at temperatures not reflected by normal AFT analyses. The updated and improved FactSage model compared favorably with the original model as well as with HT-XRD results and thus will be able to supply results in a faster and more convenient manner. In the new FactSage model, supported by HT-XRD experimental findings, it is indicated that feldspar formation (including anorthite) correlated with slag formation at temperatures around 1000°C and no slag formation in the base case coal was observed in the drying and devolitilization zone, as was to be expected. Feldspar is one is the mineral species which has the lowest AFT causing the most slag-liquid formation and forms probably as a product between the SiO2, Al2O3 and Ca-containing species. In the gasification zone it was clear that slag-liquid formed at a temperature of 1000°C, with a decrease in the feldspar content. Mullite formation was also observed in the base case sample in the temperature range 1000°C and 1100°C. The decrease in the amount of SiO2 at 1100°C is related to the formation of mullite, but also that the slag-liquid phase also contains an amount of SiO2 in the molten form.

Jan 1, 2014

By Sung. Hyejin, Kyoungkeun Yoo, Oh-hyeok Kown

The sediments near coasts and ports in Korea have been found to be contaminated with heavy metals and organic matters. So far the sediments have been dumped to landfill sites or ocean. However, the number of available landfill sites is decreasing and ocean disposal of wastes was strictly prohibited. Although physical separation processes have been found to be useful for the remediation of contaminated soil with heavy metals, because the sediments consist of fine particles, it is difficult to remove heavy metal component by physical separation processes. Furthermore, the sediments contain organic matter, so there is a concern about strong stink during the sediment treatment. The present study is aimed to develop the treatment process for removing heavy metals and organic matter from the contaminated sediments. The heavy metals and organic matter were oxidized and dissolved by electro-generated chlorine, and the chlorine used is regenerated and circulated in the leaching process. This system has economic and environmental advantages to reduce the wastewater and the oxidant consumption. The leaching results show that the metal removal efficiency increased to more than 99%, and more than 50% of organic matter was decomposed.

Jan 1, 2014

By Leon Lorenzen, Trevor J. Britz, Pierre J. Van Zyl, Ellis R. Els

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By Arun Appadurai

Pneumatic transport systems play a vital role in conveying discrete particles over a sizable distance with minimal energy consumption. However if such a system is not designed keeping particle physics in mind, it leads to intractable problems which could possibly assume dangerous proportions, including but not limited to expensive redesign of the entire system. This paper describes a novel method, which harnesses the powerful technique of Computational Fluid Dynamics (CFD) to investigate a problem occurring in rotary kilns using coal as a major fuel source. In some of the sites, a unique phenomenon of abnormally high CO emission was observed and owing to the highly random nature of occurrence, it was difficult to scientifically investigate the problem and its cause. Most of the published solutions for the high CO problem tend to concentrate on the incomplete combustion aspect of the kiln and resolve the situation by increasing the air supply thereby improving the stoichiometric ratio of combustion. This paper offers an alternate correlation that relates high CO emissions to the phenomenon of coal delivery fluctuations caused by the sub-standard operation of the coal transport system. A CFD model for the coal delivery pipe is validated by utilizing the actual process data sourced from the measurements taken from a functioning plant. The results of the model are used to derive correlative conditions that point to the unstable operating conditions of the coal delivery pipe prevalent in the industry. The conclusions are summarized into a series of recommendations for optimized design of coal delivery systems which are implemented in a pilot plant. The results irrevocably prove a statistically significant reduction in CO emissions without resorting to increased air supply and power consumption. Keywords:CFD, Pneumatic Conveying, Saltation Velocity, Particle Flow

Sep 1, 2012

By I. Dymov

"The extractive metallurgy of precious metal ores involves gravity concentration, flotation and cyanide leaching. Pre-oxidation, such as roasting, autoclaving, bacterial oxidation and other techniques, is required for processing refractory ores. Selection of the process is mainly driven by the grade, reserve and mineralogy of the target elements. The concentrations of precious metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. The objective of geometallurgy and process mineralogy is to reduce and minimize the technical risk in project evaluation, process selection, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical characterization and metallurgical testwork. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes, while mineralogy is one of the major predictive and trouble-shooting tools for many new mineral projects and operating mines. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy and highlights the importance of both disciplines in process selection and plant optimization with applicable case studies. INTRODUCTION Precious metals, including gold, silver and platinum group elements (PGE) occur in various geological settings and ore types. The concentrations of these metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. Process selection is most important in any precious metals project and is mainly driven by the grade, reserve and mineralogy of the target elements. Free-milling ores, such as Kupol in Russia, Hemlo in Canada, Grasburg in Indonesia, UG-2 in South Africa, Lac des Iles in Canada, and Noril’sk in Russia, can be processed using flotation or cyanidation with or without gravity. B2Gold Corp, a Canadian gold company, just started a number of new and under construction free-milling gold operations such as Fekola mill in Mali, Mastbati mine in Philippins and Otjikoto mine in Nambia. However, refractory ores (particularly gold ores), such as the Carlin and Goldstrike mines in the USA, Giant in Canada, Pueblo Viejo in Dominican Republic, Porgera and Lihire in PNG, Kittilla in Finland, Fairview in South Africa and Shuiyindong in China, must be processed using pre-oxidation prior to cyanide leaching. In some mildly refractory gold ores, such as Kumtor mine in Kyrgyzstan and KCGM in Australia, ultrafine grinding is required to liberate fine-grained gold particles. For some gold ores containing both free-milling and refractory components (such as Cripple Creek mine in Colorado, USA), two or more recovery processes may be required. The variability of grade, metal deportment, ore hardness and other parameters is one of the risks that encountered in development and operation of many precious metals projects. To minimize and reduce the technical risk caused by ore variability, geometallurgy and process mineralogy have been used by mining companies in the last two decades to measure and quantify the spatial variability of the deposits that are being developed. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy, it highlights the importance of both disciplines in process selection and plant optimizat"

Jan 1, 2018

Coal preparation plants usually operate with water in a closed circuit mode. In this practice, large quantities of water is continuously being recycled. To compensate the natural losses, only small quantity of fresh make up water is added into the circuit. As a result, a gradual build up of residual concentrations of flotation reagents (frothers, collectors, coagulates etc.) take place in the water and the concentration levels of the contaminants increase. Besides, the recycled water accumulates higher amounts of total dissolved components (1600 ppm) and hardness (740 ppm) than the fresh water. Nearly 80 ? 85% of the process water used in a coal preparation plant is utilized in treating the coal fines in flotation circuit. The presence of certain alkali earth metal ions (e.g., Ca++, Mg++) may adversely affect the flotation performance as they precipitate sparingly soluble hydroxyl complexes on the coal surface and change its surface charge. These studies showed that the use of recycled water in flotation has a significant effect on the selectivity and kinetics of the flotation process because, the dissolved compounds, both inorganic and organic, alter the chemistry radically. By treating the recycled water through a softening process, the concentrations of alkali earth metals and hardness were reduced significantly. The concentration of alkali earth metals and hardness were reduced to 10 ppm and 35 ppm respectively in the softened recycle water. From the selectivity studies, it has been observed that the flotation yield and recoveries increased by four to seven units by softening the recycled water. The kinetic studies indicated that the clean coal particles followed first-order kinetics. The kinetic parameters namely, flotation rate constant (k) and maximum recoveries (R8) of flotation, were found higher with softened recycle water than the recycled water. This reduces the residence time in the flotation cell and thereby, increases its productivity. Keywords: coal flotation, hardness of water, water chemistry, softening process, selectivity, kinetics, flotation rate constant and maximum recovery

Sep 1, 2012

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By Kazutoshi Haga, Atsushi Shibayama, Kosuke Nishioka, Yasushi Kihara, Altansukh Batnasan

The aim of this study was to investigate the feasibility studies of seawater in flotation of a 1.5 mass % of copper containing copper sulfide ore. Effects of seawater, various frothers, and different distilled water/seawater ratio on flotation of copper sulfide ore were studied. Surface properties of native copper ore and sea water soaked were examined by using FT-IR spectrometry. Chemical contents of the copper sulfide ore and after flotation were identified using XRD studies. XRD pattern showed that the main constituents of the copper sulfide ore are chalcopyrite (CuFeS2), bornite (Cu5FeS4). Flotation experiments were carried out using mechanical agitation flotation equipment with a mineral separation type flotation cell. Froth flotation experiment was conducted using calcium hydroxide was used as a pH adjuster, using methyl isobutyl carbinol (MIBC), dow froth 250 (DF 250) as frothers and potassium amyl xanthate (PAX) as collector for the copper recovery from the copper sulfide ore containing chalcopyrite and bornite. The results showed that the copper recovery by flotation was dependent on the flotation medium and frother. The main results showed that the copper recovery by flotation was dependent on the process water and frother. The copper recovery reached 97 % and 87 % in the distilled water flotation and seawater flotation with MIBC, respectively. For seawater flotation with DF 250, the Cu recovery achieved near 95 % and grade of Cu in the froth product after 5 min flotation was reached 29.8 mass %.

Jan 1, 2014

By Y. M. Zhu

Lead in environment often causes a serious health hazard. The removal of Pb2+ from aqueous phase is a beneficial project. In this paper, deposited Saccharomyces cerevisiae (S.c.) was chosen as adsorbent, Pb2+ ions as adsorbate, and the process of biosorption was studied. The dynamics of the adsorption was investigated. The adsorption mechanism of Pb2+ by S.c. cells was also investigated by detecting microstructure, zeta potential under different pH value, FT-IR spectra of the S.c. particles before and after biosorption. It was shown that the biosorption of Pb2+ by deposited S. c. is a rapid process, and the adsorbing equilibrium is reached within 10 minutes. The Zero point of zeta potential of S.c. cells is pH=3.3. When 2.0<pH<3.3, there exists biosorption (biosorption rate 76%~88%), which means static bio-sorption been not the only kind of biosorption. FT-IR spectrum analysis showed that groups on bacteria surface were mainly characteristic groups of protein and amylase; oxo-groups and nitric-groups on S.c. cell surface could chelate with heavy metal ions. Chemical adsorption might exist in the process.

Jan 1, 2014

By Chuanyao Sun, Yang Yu, Zhen Guo Song, Wei. Ming’An

"Carbonate minerals are very important mineral source of extracting metal, radioactive element and rare earth elements. Furthermore,some carbonate minerals, such as calcite and dolomite, are common and important components of sediments and sedimentary rocks. Many flotation processes involve the separation of valuable minerals with carbonate minerals. So it is of great significance to the flotation theory and industrial practice to investigate the flotation behaviors of carbonate minerals. As regulators, metal ions play a major role in minerals flotation. The study of influence law of metal ions on minerals flotation is helpful to eliminate or utilize the effect of metal ions. In this study, calcite and smithsonite laboratory scale flotation, surface analysis and zeta potential determination in the presence of Fe(II) ion were performed to investigate the effect of Fe(II) on carbonate flotation. The results show that Fe(?) depresses the flotation of calcite and smithsonite. The depression effect of Fe species on calcite and calamine flotation can be improved with the increase of Fe(?) concentration. The zeta potential measurements and surface analysis show the existence of iron hydroxide products on mineral surface, which may be link to carbonate site instead of exchanging with calcium on the mineral surface. Fe species on the mineral surface inhibit the interaction between the reagents and calcite/smithsonite through the formation of surface precipitation coating on the calcite/smithsonite surface when the Fe(?) concentration is higher."

Jan 1, 2014

By F. Xie

Low gold and silver leaching kinetics has been commonly observed in traditional gold-silver cyanidation process, especially in those heap-leaching operations. The reactivity and availability of oxidant was believed to be the critical limitation for gold and silver dissolution. The occurrence of silver sulfide such as acanthite (Ag2S) in the ore may also result in low overall silver extraction. Leaching of gold and silver sulfide in the ferricyanide-cyanide solution has been investigated through rotating disc tests and the assistant effect of ferricyanide on increasing the dissolution rate of gold and silver was noticed. The potential use of ferricyanide as an auxiliary oxidant in gold/silver cyanidation process was proposed based on the results of leaching of gold-silver ores.

Jan 1, 2014

By Masakazu Niinae, Tasuma Suzuki, Mai Moribe, Yohhei Okabe

Bench-scale electrokinetic experiments were performed to elucidate the electrokinetic remediation mechanisms of arsenate from artificially contaminated kaolinite. The electrokinetic experiments in which a constant voltage was applied demonstrated that high soil pH favored arsenate remediation with respect to both the remediation time and electricity consumption. It was also demonstrated that applying a pulse voltage (1 hour ON, 1 hour OFF) significantly improved the electricity consumption efficiency when the soil pH was maintained at the initial value during the experiments; this trend was not observed when the soil pH was gradually increased from the cathode side. These electrokinetic experimental results indicate that the remediation rate-limiting step varied with soil pH. When the soil pH was maintained at the initial value of 7.2 during the experiments, arsenate desorption was the remediation rate-limiting step rather than the migration of dissolved arsenate toward the anode. Conversely, when the cathode pH was not controlled and the soil pH was correspondingly increased gradually from the cathode side, the migration of hydroxyl and desorbed arsenate ions toward the anode played a more important role in the control of the overall remediation efficiency.

Jan 1, 2014

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012