Search Documents

By P. J. Yttrup

Small diameter timber piles are used in Australia to solve foundation problems in soft or filled ground and expansive soil. The paper describes the results of pile load tests to develop simple methods for bearing capacity determination and observation of the performance of piles in expansive soil.

Jan 1, 1989

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers' common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Upendra L. Karna

The pile capacity gain with time evaluated and implemented for the construction of the Route 21 Viaduct in Newark, NJ, U.S.A is discussed in this paper. The project consisted of the replacement of more than 3.2 km of viaduct and ramps. The project site consists of thick residual materials deposited by the Wisconsin Glacier over sedimentary rocks. The upper portion is glacial-lacustrine deposit underlain by marginal morainic till and stratified drift. Subsurface investigations identified significant variations in layer thickness and grain size consistency. The site was characterized into 4 Soil types, based on subsurface soil behavior. Closed end 600 mm and 450 mm diameter driven pipe piles were used for the foundation. Loading tests conducted during an advanced construction contract, established that a significant soil set-up could be expected. For the first construction contract, a pilot loading test program consisting of 112 dynamic loading tests and 77 re-strikes (at 2 to 4 weeks) using the PDA (Pile Driving Analyzer) with CAPWAP (Case Pile Wave Analyses Program) was conducted to establish the soil set-up behavior. Nine (9) quick static loading tests were conducted to substantiate the long-term pile capacity. Based on the loading test results, average set-up factors were established and utilized for developing production pile driving criteria. Bearing resistance with depth was analyzed and reviewed. The set-up factors varied significantly, ranging from 1.05 to 1.89, and averaged about 1.30. Conclusions are derived. Set-up factors behavior for each soil type plotted by linear regression are presented and discussed. An appropriate set-up with time relationship for a glacial soil is suggested.

Jan 1, 2006

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane 'Westway' would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960's and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By George Goble

I hope that after the long evening and all the exercise that some of you took you won't be completely exhausted to listen to a little bit about pile testing. The topic that 1 have been given is pile testing. It seems to me useful to break this topic into some smaller pieces so that we can try and organize our thought a bit. As I understand the terms "pile testing", I believe we are really referring always to capacity, one way or another, so I am suggesting that we organize the things we are doing in terms of measurement of soil capacity and pile capacity. There are obviously two failure modes and we frequently speak of pile integrity rather than structural pile capacity, but it's really capacity that we are concerned about. Further within these breakdowns I am suggesting that we might look at the topic of soil capacity in terms of static methods and dynamic methods and, finally, within each one of these, measurements of axial capacity and measurement of lateral capacity. Also here some of these subdivisions might be there for the purpose of symmetry and finally the same sorts of breakdown in Pile Capacity area.

Jan 1, 1994

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By D. V. Roberts

Approximately 800 private consulting engineering firms in America specialize in geotechnical engineering. The gross income from these firms totals about $500 to $600 million per year. Sixty-five to seventy-five percent of this geotechnical work is per­formed by consulting engineers that belong to the Association of Soil and Foundation Engineers (ASFE). This paper presents statistics concerning the business activities and functions provided by ASFE member firms. The procedures used in typical projects are described. The paper concludes with a summary of major trends which are impacting the American geotechnical practice today.

Jan 1, 2010

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987