Search Documents

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By S. G. Shabestari, S. Saeidinia, P. Mokarian

"The experiments were conducted to investigate the influence of various process parameters in rotary degassing of aluminum alloy AS5U3G. Degassing was carried out by use of argon inert gas. The flow rate of the gas was investigated in the range of 12 to 21 L/min., 350 to 500 rpm rotor speed, 6 to 12 minutes degassing time, and 755°C to 780°C melt temperature. Degassing efficiency was evaluated through measuring the density of RPT samples. By optimizing the process parameters, RPT sample density was increased up to 2.73 g/cm3, which guaranties the production of high-quality aluminum castings. Tensile strength and elongation were increased considerably by degassing process. Scanning electron microscopy (SEM) shows small size and well-distributed microporosity. IntroductionOne of the major problems associated with the casting of aluminum alloys is the formation of gas porosity. Aluminum and its alloys are very susceptible to hydrogen absorption. Because solubility is much lower in solid state than liquid state, hydrogen atoms leave their position during solidification and combine together to form hydrogen molecules. These micrometer- scale cavities, called microporosity, cause the reduction of mechanical properties, particularly strength, ductility, fracture toughness, fatigue resistance, pressure tightness, and corrosion resistance (Laslaz, 1991; Jorstad and Rasmussen, 1993; Sigworth and Wang, 1994; Korasani, 1996; Anson and Gruzleski, 1999; Zhang et al., 2000). To avoid these problems and produce good quality castings, it is necessary to remove hydrogen from the melt. Several methods are available for degassing aluminum melt. One of them is a rotary degassing system using inert gas, e.g. Ar or N2. Various thermodynamic and kinetic factors govern the removal of hydrogen from molten aluminum (Anderson, 1987; Sigworth, 1987; Pignault, 1993; King and Reynolds, 1995). These are some parameters that affect degassing efficiency. Some of them are discussed here and some are examined in this project."

Jan 1, 2004

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

The Nak?azdli First Nation and the municipality of Fort St. James are located in the Stuart Lake/Nak?al Bun area and are not unfamiliar to mining. These northern British Columbian communities have been associated with the historic Pinchi Lake Mercury mine and today are closely linked with British Columbia?s newest mine, the Mt. Milligan mine. Prior to the construction of Mt. Milligan, community health and social service providers were concerned about potential impacts that would occur from new mineral development activities. This concern has led to a partnership between the above communities and researchers with expertise in the area of mining and health. This paper describes: the current mining and health environment with a focus on British Columbia; mining trends in the Stuart Lake/Nak?al Bun area; the current community-based health research project funded by the Vancouver Foundation and the Canadian Institutes of Health Research, and; a suite of community-based health recommendations to mining companies on key issues to consider when developing projects near municipalities and Aboriginal communities in Canada, based upon one of the newest mines under development in Canada.

Aug 1, 2013

By Hamid Butt

Information Technology ??Advanced Information Technology is dramatically changing information flow within organizations. This enables employees to have information at their fingertips to make informed and prompt decisions. ??Real-time information allows timely analysis, which dramatically reduces cycle times, making organizations faster and more flexible. Business Challenges ??Continual growth of mining and Mine mobile fleet.??Increasing maintenance costs. ??Difficult to identify and troubleshoot equipment problems while equipment is operating. ??New equipment is increasing in complexity and cost. Therefore, each failure results in a greater impact to production and cost. ??Troubleshooting practice is reactive. ??Protect and optimize the use of mining assets to realize maximum business value. ??Maintenance and Operating information is not easily accessible ?no near real-time system that provides complete information.

May 1, 2006

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By James F. Archibald

Research has been conducted for the Workplace Safety and Insurance Board of Ontario (WSIB) to characterize thin, spray-on lining materials (TSLs), as well as combinations of TSLs and conventional spray supports, and to assess their capacity for inhibiting damage created by mining-induced rockbursts. This study has been performed to assess the capabilities of such support systems for preventing rock and support material damage that often results due to rockbursting. A variety of TSLs and other spray support media were subjected to the effects of simulated rockbursting, through use of explosive detonation trials, to evaluate their damage mitigation capacity. Results have validated that TSLs and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In civil engineering construction, and typically in underground tunneling operations where concrete linings are applied, liner deterioration is a continuing and pervasive problem that often requires expensive and time-consuming rehabilitation effort. The ability of TSLs to provide effective concrete structural reinforcement while providing sustainable resistance against underground or restricted environmental hazards, as with fires or dynamic failure events, may permit wider use of TSLs than is currently foreseen by the mining industry. Significant benefits for use of TSL materials in concrete liner rehabilitation and for concrete material protection have been assessed.

May 1, 2006

By M. Schmidt, P. Nord, M. Larinkari

Cathode stripping machine technology has been developed significantly both in electrorefining (ER) and electrowinning (EW) applications in the last ten years. The main driver has been robotic cathode handling, which has enabled increased flexibility to meet different layout and material handling requirements for both ER and EW processes. Additionally, cathode stripping stations have been continuously developed to optimize speed and to reduce mechanical stress of permanent cathodes. 'taco' type cathodes have been proven as beneficial approach for high capacity operations (particularly in Cu ER), where over 600 cathodes per hour continuous throughput has been achieved. However, the latest developments also apply to split type cathode stripping. Besides material handling, the modern cathode stripping machine has also an important role to provide information for production and quality monitoring. This paper describes the latest developments from the field of copper cathode stripping based on several different projects implemented in the recent years. INTRODUCTION After introduction of the permanent cathode technology in the late 1970s, it became the prevailing technology in copper refineries over the traditional starting sheet process by the end of 1980s. The main driver was less labour-intensive production due to fewer processing steps required along with more automated electrode handling equipment (cathode stripping machine, anode preparation machine, anode scrap washing machine and tankhouse cranes). Since then the design of the cathode stripping machine has followed the development of permanent cathode technology. The main development steps so far can be summarized as follows: Full Deposit Stripping Machine (FDSM) based on waxed permanent cathodes or cathodes with bottom edge strips resulting in split cathodes (copper sheets separated, see Figure 1) Wax less cathode stripping based on V-groove on bottom of the edge strip resulting in either ‘taco’ cathodes (enveloped copper sheets, see Figure 1) or split cathodes Full Deposit Robotic Stripping Machines (FDRSM) using 1–5 robots for permanent cathode handling and cathode stacking.

Jan 1, 2019

By Grant Goddard

Cameco?s ?Double U? Strategy ? Double existing production ? To 40 million lbs U3O8 annually ? By 2018 ? Existing operations ? Saskatchewan ? United States ? Kazakhstan ? Projects under evaluation ? McArthur River expansion ? Kintyre (Australia) ? Inkai Block 3 (Kazakhstan) ? Development properties ? Cigar Lake project Measures of Success ? Safe, healthy and rewarding workplace ? Supportive communities ? Clean environment ? Outstanding financial performance

Nov 1, 2011

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By Robert B. Parsons

"Exploration and development of mineral resources in developing countries by Canadian-based multinational mining companies is becoming increasingly common. One problem being encountered is that the objectives of the governments of developing countries can differ from those of developed countries. These objectives are not always consistent with maximizing returns from the projects, which can create conflicts between the mining company's responsibility to its shareholders and the desire to be a good corporate citizen. This article discusses how a mining tax regime can be designed to make the social goals of a government consistent with the economic goals of the company.IntroductionAt the recent International Seminar on Mining Taxation organized by CIM and the United Nations there was considerable discussion about the role of international mining companies operating in developing countries. Not surprisingly, given the diversity of backgrounds of individuals attending the Seminar, there were different opinions about what this role should be.Government PositionRepresentatives of governments pointed out the strong desires of their countries for technology, high-level technical training of their workforce, increased employment, and development of social infrastructure. They pointed out that, to a large extent, these objectives could be more efficiently met by mining companies operating in the country than by the governments themselves. For example, a multinational mining company (""MMC"") would have extensive knowledge of the various technologies available, and would have performed a detailed evaluation of the mineral resources before choosing the most cost-efficient technology for that project. They would, therefore be in an ideal position to assist the country in importing and developing such technology. Similarly, the company could provide opportunities for hands-on training, both at the technical and managerial levels, which would otherwise be unavailable to the government."

Jan 1, 1991

By Salvador Gómez, Rodolfo Espinosa, Jaime Bravo, Leopoldo Gallas

"Compañia Fresnillo, S.A. de C.V. - Proaño Mine, is owned by Industrias Peñoles S.A. de C.V. (Peñoles). The Proaño Mine, is one of the richest silver underground mines in the World, and for this reason, production capacity has always being expanded, based on generated reserves. Reserve generation has not being an easy task as this is a vein type deposit.This paper presents the growing stages at the Concentrator, for about the last twenty years; which can be listed as follows:1.,Increase in capacity from 1,000 to 4,500 tonnes per day, at several stages; on the same infrastructure, and without production interruptions.2.,Addition of a new flotation circuit to recover a zinc concentrate with a high silver content.3.,Installation of a semi-autogenous (SAG) mill, to replace a conventional crushing circuit. 4.,Modernization. Installation of an on stream analyser, an automatic reagent dosification system, 4500 ft3 unit cells, pressure filtration, a closed circuit video system to help process monitoring, an automatic ball addition system for SAG and ball mills, and on-line particle size analysers.5.,Silver recovery from old tailings, installing a 2,350 tonne per day treatment plant.INTRODUCTIONIndustrias Peñoles, S.A. de C.V. (Peñoles)Peñoles’ mission is to add sustainable value to non-renewable natural resources. Peñoles seeks to: build long-term shareholder value; provide customers with the highest quality product services; maintain productive long-term relationship with suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which operates; protect and preserve the environment."

Jan 1, 2002

By Carol J. Odell

As a mining social practitioner, social indicators are within the purview of required competencies. A situation, where the ER manager requested assistance in quickly deriving a few social indicators for the strategic plan motivates this paper: despite ample technical knowledge about indicators, a clear understanding of stakeholder aspirations and concerns, as well as familiarity with management priorities such a request required reflection to produce a satisfactory approach, which combined pragmatism with enough academic rigour to provide reliable measures, while being justifiable to management who are unfamiliar with many of the pertinent debates. Importance: Social indicators enable the identification of more and less effective mine-community engagement strategies as well as providing primary data to better understand how the mine-community social system responds to different interventions, thus guiding future engagement plans. In addition social indicators: ? Assist communication about social strategies with Engineering and Operations management, using a quantitative language that is familiar to them. ? Provides concrete data to engage stakeholders to discuss progress and challenges arising, to move discussions towards technically robust strategies and away from politically interested proposals. ? Finally, social measurement is required more and more in due diligence, covenants and ongoing monitoring in Independent Engineering assessments of projects for financing. This paper begins by considering some technical considerations that are useful to guide indicator development. It then introduces the field research informing this paper and discusses some useful results in the light of further applicable concepts from the literature. The paper ends by considering corporate aims in applying corporate social responsibility (CSR) programs and discusses the application of the research for practitioners at mining operations, in the light of these aims.

May 1, 2010

By M. J. Beus

Many mines in Canada, the United States and South Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due to the excessive weight. It has been suggested (DeLorme, 2000) that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm (13/4 in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg (10 ton) skip could exceed the safety factor of the rope. To improve on the current understanding of the mechanical behaviour of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modelling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca, 1999), is used to simulate the structural behaviour of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modelling on the wire rope will be discussed.

Jan 1, 2002

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By Trevor Hamm, Nick Holl

"Cameco Corporation is operator of the world's richest uranium project, the Key Lake mine/mill complex, located within the Athabasca region of Northern Saskatchewan. Mineable resources from the Key Lake ore bodies with an average U,08 content of 2.5% will be exhausted by the year 2000 and open pit mining at Key Lake will be phased out at that time. The mill will continue to operate at increased capacity, using high grade ore from the McArthur River project, a new underground mine at a distance of about 80 km from the Key Lake site. The McArthur River ore with an average U308 content of about 15 % will be blended with separately stockpiled low grade materials from Key Lake with a U,08 content of about 0.1 %. The average (blended) mill feed grade will be about 4%, similar to peak concentrations found in Key Lake ore.The Key Lake ore tailings are presently being placed in the mined out Deilmann pit under sub-aerial conditions, using spigots and a highly efficient pit/tailings drainage system. The tailings resulting from the processing of the blended McArthur River ore will be deposited on top of the Key Lake ore tailings under sub-aqueous conditions. This staged approach shows distinct technical and environmental advantages over an alternative, fully sub-aerial in-pit deposition scheme.The first part of this paper presents an overview of site specific geotechnical and hydrogeological features found at Key Lake and details some of the extensive test and modelling work that was required for environmental impact predictions during the development phase of the facility. The second part of this paper deals with tailings modifications, innovative placement technologies and drainage methods that have been (and will be) employed at the Deilmann Tailings Management Facility {TMF) to produce a highly consolidated tailings body under non-buoyancy conditions. The application of this technology at Key Lake is expected to produce a tailings ""plug"" in the Deilmann TMF which will have a permeability similar to or lower than the original in-situ Deilmann ore, resulting in a minimization of contaminant mass loadings to the environment both during operation and after decommissioning."

Jan 1, 1998