Search Documents

By J. Fellowes, Z. Liang, J. Robson, M. Kenyon

"Dispersoids play a significant role in the recrystallization and texture development for wrought Al-Mg-Si (6xxx series) alloys by inhibiting grain boundary motion. It is therefore important to understand the precipitation kinetics of such particles. It is the additions of Mn and Cr in Al-Mg-Si based systems that can lead to dispersoid phases being formed. These phases are currently thought to nucleate on ß’-Mg2Si via an intermediate semi-coherent precipitate. Scanning transmission electron microscopy (STEM) has been conducted to study the precipitation of a-Al(CrFe)Si and a’-AlCrSi dispersoids. Corresponding electron dispersive spectroscopy (EDS) has been used to distinguish the dispersoids. The volume fraction and size distribution of dispersoids has been measured as a function of distance across a grain. Electron probe microanalysis (EPMA) has been conducted to study the inhomogeneity of elements in the cast structure and the effect on dispersoid precipitation. Dispersoid free regions have been observed in the microstructure correlating to regions depleted in the dispersoid forming elements.INTRODUCTION Al-Mg-Si (6xxx series) based alloys are increasingly being used in the automotive industry. The primary reason is to reduce the weight of vehicles, resulting in a reduction of CO2 emissions and increased fuel efficiency. The demand for 6xxx series is predicted to increase over the coming decade. Due to the high cost and CO2 emissions produced by raw extraction of aluminium, close loop recycling of these alloys becomes a more important process. However recycling of automotive alloys can be difficult due to pick up of impurity elements such as Mn, Cr and Fe. The addition of these elements can form dispersoid particles during early heat treatment processes. Although a controlled population of dispersoids is necessary to control the grain structure during thermo-mechanical processing, a significant change to the dispersoid population due to a composition change could profoundly influence the final microstructure, affecting the final properties of the material. More research is required on the precipitation and effect of additional minor alloying elements; in order to increase the 6xxx series alloys recyclability."

Jan 1, 2018

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

By M. Cala

Underground coal gasification is technology which enables energy to be extracted from coal beds where mining by means of classical methods is either impossible or uneconomical. The process of coal gasification itself is a complex phenomenon which includes chemical and physical processes: thermal, hydrological and mechanical. Additionally, the analysis of underground coal gasification is difficult to carry out for environment reasons, this being due to the local characteristics of the areas where it is carried out. This paper deals with interaction of geo-reactor with surrounding rock mass, it omits the chemical processes inside geo-reactor itself. Due to the complexity of the processes proceeding and during underground coal gasification coupled with minimal practical experience in using this technology, it is difficult to estimate its influence on the surrounding rock mass. Within this scope, the use of numerical programs can be useful. This paper presents a trial of modeling the processes accompanying underground coal gasification. The processes proceeding and during the underground coal gasification are characterized, and the significant, specific phenomena are discussed, with respect to the influence on the surrounding rock mass. For the chosen processes, examples of numerical calculations are presented. These enabled conclusions to be drawn and also provided directions for the modeling of the underground coal gasification processes.

Aug 1, 2013

By Stanislaw Trenczek

Natural hazards such as rock bumps, methane, coal dust explosions, airborne respirable dust, outbursts of gas and rocks, water, radiation caused by natural radioactive materials, spontaneous fires, and climatic hazards, occurring in the Polish hard coal mines, should be controlled. These hazards are characterized by different scale levels numbered from 2?5. To recognize the amount and levels of hazards, research works were carried out in 109 mining districts of mines belonging to Jastrzebska Spólka Weglowa, Katowicki Holding Weglowy and Kompania Weglowa. These are 86 % of all mines and could be regarded as representative of the majority of Polish mining. The hazards have been classified as regards the frequency of their occurrence as: commonly occurring ? with a frequency of 100 % (like airborne respirable dust and fire hazards), high occurrence frequency ? frequency from 60 to below 100 % (methane hazard ? 83.5 %, coal dust explosion hazard ? 92.0 %, and water hazard ? 99.1 %), medium occurrence frequency ? from 30 to below 60 % (rock-bump hazard ? 52.3 % and climatic hazards ? 51.4 %), and episodic occurrence frequency ? below 30 % (outburst of gas and rocks and radioactive hazards). The dynamics of effects of growth in hazard levels to their intolerable values is diverse. Some of them are passive in nature, which allows for longer observation of changes and appropriate early response (as for climatic and spontaneous fire hazards). However the majority of them take on the character of disasters, like methane or coal dust explosions and damage of the excavation structure ? as occurs after a rock-bump or rock outburst; and creation of an atmosphere unfit for breathing ? during open or spontaneous fires, or after gas outbursts containing methane. There are also latent hazards whose effects do not influence indeed a process of production; however they are detrimental to health when a worker is exposed for a long time to airborne respirable dust and radiation. For other types of hazards a level of danger may be only estimated. Since the systems monitoring allows a wider range of control, therefore, aside from rock-bump and methane hazards, there are monitored also fire hazards including measurements of other air parameters (velocity, pressure, humidity, temperature, O2, CO2 concentration). A few types of monitoring systems are used in Polish mines, like the monitoring systems for environmental parameters such as SMP-NT, SMP-NT/A, the telemetric systems CST-40, CST/A, including the computer-aided system for methanometry control officer SWµP, the computer-aided measuring systems KSP-1, KSP-2, KSP-2C, or the production and safety control system VENTURON. The underground part of the systems monitoring of natural hazards contains measuring devices and equipment for automatic control (power-off) of machines and electric devices in case of increased methane hazard. The surface part of the monitoring system allows the measuring data to be visualized and pre-alarm (warning) and alarm states to be displayed. Furthermore it makes it possible to archive and report the data and to control the underground supply and signalling devices. The EMAG Institute developed monitoring methods to extend a measuring range of monitored parameters (such as methane and fire hazards) as well as to monitor so far unmonitored hazards like dust hazards (by continuous monitoring of dust levels in mine air) and climatic hazards (by online monitoring climatic parameters of mine air).

Aug 1, 2013

By S. G. Shabestari

In the metal casting industry an improvement of component quality mainly depends on better control over the production parameters. Thus, thermal analysis cooling curve of the alloy is used for process control in aluminum casting industry. Cooling rates of the alloy during solidification process affect microstructure, grain size, eutectic silicon morphology, and dendrite arm spacing (DAS). In this research, effect of cooling rate on the microstructure and solidification parameters of 319 aluminum alloy that is a widely used alloy in automotive industry, has been investigated by means of thermal analysis. Seven different cooling rates have been obtained by using CO2-bonded silica sand molds with two different wall thicknesses, hot-work tool steel molds (H13) with and without coating, thin-wall steel molds with different coatings. In each case, cooling curve and first derivative cooling curve have been plotted by use of very accurate thermal analysis equipment. Effect of different cooling rates on solidification parameters e.g. Nucleation temperature (TN,a), nucleation undercooling (ATN,a), recalescence temperature (TR,a), solidification range (AT,s), and total solidification time (t 0 have been studied in the liquidus region. Microstructural evaluation has been carried out and DAS were measured in all solidification conditions. A numerical equation was proposed to predict cooling rates via measuring DAS in 319 aluminum alloy. Nucleation process and the effect of cooling rate have been interpreted by using thermal analysis cooling curves and microstructural study.

Jan 1, 2004

By P. A. Bahri, D. G. Dixon, T. M. Woodward

A comprehensive mathematical model of the Sherritt-Gordon ammoniacal pressure leaching process at K winana Nickel Refinery has been constructed. The process is comprised of six autoclaves functioning as a three-stage leach circuit, operating over the temperature and pressure ranges of 85-95°C and 750-1000 kPa, respectively. The process chemistry forms a complex series-parallel reaction network, characterised by: (1) the gas-liquid mass transfer and reduction of oxygen, (2) the oxidation of eight distinct minerals, (3) the oxidation of sulphur, and successive reactions involving various intermediately oxidised sulphur species, and (4) the oxidation of Fe(II) to Fe(III), and subsequent precipitation as a hydrated ferric oxide. Material balances were developed for species in all three phases, and an energy balance to account for all reactions and phase conversions. The multiple convolution integral (MCI) statistical reactor model was employed for the scale-up of particle kinetics. The model has been validated against plant data, and simulation results are in agreement with plant performance.

Jan 1, 2005

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

By P. H. Rodriguez

The aquatic hazard classification system of the OECD and EU requires that sparingly soluble metal substances (SSMS) be tested using the OECD Dissolution/Transformation protocol in order to quantify the release of the ecotoxicological relevant species (dissolved ions). The SSMS category contains massive forms of metals, which due to their low solubility and slow transformation characteristics are a special case. The main factors that produce the release of metal into solution are exposed surface loading, pH, and stirring rate. The classification system at present prefers the use of mass loading as opposed to surface loading, in which case the amount of metal released will primarily be a function of the pH, and mass loading. Within the framework of the European Copper Voluntary Risk Assessment, coordinated by the European Copper Institute, we have proposed and developed a methodological procedure in which we demonstrate that surface area is an intrinsic property of a SSMS and we link the exposed surface loading to the toxicity reference value in order to obtain an aquatic hazard classification for massive metals. As example, the aquatic hazard classification for copper massive will be discussed. This approach is recommended for metal massives and metal powders.

Jan 1, 2007

By R. MacRosty

The demand to increase production levels in smelting furnaces has driven the increase in the power levels. Consequently, greater cooling capacity of the furnace shell has been necessary, resulting in the widespread use of water-cooled elements to protect the refractory linings. Since water ingress into the furnace is an explosion hazard, monitoring and maintenance of the water-cooled elements is of key importance. Some of Hatch's recent research and development efforts have been focused on methods to provide an increased level of monitoring of water-cooled furnace elements; this paper focuses on two technologies developed for this purpose. The first involves the installation of a fibre optic temperature sensor in a water-cooled tapblock. The sensor is capable of providing high accuracy temperature measurements with a fine spatial resolution throughout the tapblock. Hatch has already developed a diagnostic system that uses multivariate statistical analysis to interpret the large quantities of data generated by the sensor. A second technology under development is concerned with enhancing the operating integrity and safety through detection of leaks in the water circuits. A successful leak detection strategy requires minimal maintenance and the ability to detect minute leaks. An instrument that meets these criteria has been investigated and is currently under development. This paper focuses on the technology and results from the test work that has been completed to date.

Jan 1, 2007

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

By V. Labiouse, M. Souley, N. Lafrance, C. Auvray

"Chalk rocks have been used for centuries as a strong building material and for the production of lime. The shallow underground room-and-pillar quarries where the chalk was extracted are now abandoned and endure the effects of time and weathering, increasing their risk of collapse. The risk of instability, involving natural or anthropic underground structures, is an issue for more than 10 000 towns in France.In order to investigate the causes of underground quarry collapse and to aid prevention strategies, we carried out a study of the physico-mechanical behaviour and ageing of chalk in abandoned pillars in two underground quarries, in situ-instrumented by INERIS, in the Parisian Basin, France. Core samples were drilled horizontally from pillars in the Saint-Martin-Le-Noeud dolomitic chalk quarry (Oise, France) and the Estreux glauconitic chalk quarry (Nord, France).Uniaxial tests were performed on dry and saturated cylindrical plug samples extracted perpendicular to the cores at regular distances along their lengths. Physical and mechanical properties were obtained. The dolomitic chalk (Saint-Martin-Le-Noeud) exhibits variation in mechanical and physical properties with horizontal pillar depth. Both density and compressive strength seem to increase outwards from the pillar-core to the pillar-wall. This is the opposite of that would be expected from a purely mechanical point of view. SEM analysis revealed progressive degradation and homogeneity of the grains from the edge to the inside of the pillar. At the pillar wall, the crystal faces are well-defined, almost euhedral, and the grains are of variable size. In contrast, at the inside of the pillar, crystals are finer-grained and are anhedral with highly degraded edges. In the physico-mechanical tests and SEM analyses performed on the Estreux samples, no significant variation was observed between the pillar-walls and pillar-core. However, dissolution marks were observed along the entire length of the half-pillar core."

Jan 1, 2015

By P. Lin, S. G. She

"In June 1985, Chinese Society for Rock Mechanics and Engineering (CSRME) was established. During the past 30 years, various major achievements are made in the discipline of rock mechanics and rock engineering field, especially in the last ten years. This paper will discuss the main rock engineering progress in association with China National Science and Technology Awards, “973 Program”, and “Tan Tjongkie Lecture”. The current status of rock engineering in China and some hot problems are summarized. Furthermore, some suggestions are given for addressing those problems. INTRODUCTIONThe modern concept of rock mechanics and engineering was initiated and developed after the Second World War. In this regard, the International Society for Rock Mechanics (ISRM) was established in 1962, subsequently further promotes its development. In June 1985, the Chinese Society for Rock Mechanics and Engineering was established. Various chief scientists, including professors Tan Tjangkie, Pan Jiazheng, Sun Jun, Wang Sijing, Qian Qihu, have made their huge efforts to the development of Rock Mechanics and Engineering in terms of the large-scale rock engineering projects in China.The achievements in the last 30 years significantly promote the development of China in different fields, such as energy, transportation, national defense and other national economy and major infrastructure facilities (Wang et al. 2004; Qian 2010, 2011). In other words, these projects also promoted the science and technology progress in rock mechanics and engineering across the world. Reviewing and analyses of the experiences on those key rock projects are beneficial to its technological development. She and Dong (2013), in view of literature statistical analysis, discussed the status and research progress in rock mechanics field associated with the last 30-year China's developments, including the rock strength and deformation theory, rock fracture and damage mechanics, the constitutive relation of rock dynamics, rock field coupling, rock reinforcement and stability analysis, etc. The challenging issues in rock mechanics were also proposed, which are the main concerns in rock engineering practices, engineering exploration, design, construction and operation."

Jan 1, 2015

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By N. J. Shackleton, N. A. Chapman, V. Malysiak, C. T. O’Connor

In this study, the effect of using conventional crushing and high-pressure grinding rolls (HPGR) in combination with dry or wet milling was investigated using a base-metal sulphide (BMS) sphalerite and a platinum group mineral (PGM) ore to determine how these processes affect the flotation performance. In sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc, whereas in PGMs, similar treatment produced the poorest results. The results were investigated further by the effect of factors such as percentage liberation and particle size on the flotation results.

Jan 1, 2012

By M. Jorgensen, I. Markland, D. Shuck

"The McLaughlin Mine owned by Homestake Mining Company is located 70 miles northeast of San Francisco in California's coastal range. The mine began operations in February of 1985. The mill currently processes 3,000 short-ton per day of sulfide ore that has an average grade of 0.15 ounces of gold per ton, plus another 3,000 tons per day in a newly completed oxide circuit. Annual production from the mine totals over 200,000 ounces.The sulfide ore extraction process involves three basic steps, grinding, oxidation of sulfide minerals in an autoclave, and cyanide leaching for recovery of gold in a carbon-in-pulp circuit. This process, which incorporates a new technology where oxidation of sulfide minerals is conducted prior to cyanide leaching to facilitate gold recovery, was successful from start-up. However, limitation in the grinding mills initially limited sulfide tonnage throughput.This paper discusses modifications made in the grinding circuit, both mechanical and operational, to resolve it deficiency. The SAG mill, in particular, was unable to achieve design tonnage initially and proved to be most troublesome. Complications occurred due to the hardness and variability of ore being processed, short component life, and a lifter /liner arrangement that had to be tailored to the particular circumstances at McLaughlin. IntroductionHomestake Mining Company's McLaughlin Mill, located in northern California, was designed to process a refractory gold ore at a rate of 3,000 tpd to render the ore amenable to cyanidation. Seven years transpired between discovery of the near-surface ore body in 1978 and the February, 1985 plant start-up. Development of the McLaughlin mill and open pit gold mine hinged on the use of autoclave technology to achieve design recoveries."

Jan 1, 1991