Search Documents

By C R. Evans

Whole-rock and muscovite potassium-argon dates from selected low-grade metamorphic rocks of Precambrian age in the Canadian Rocky Mountains near Jasper, Alberta, were obtained to ascertain the age of the source terrain and the age of the metamorphism. Ten argillites gave whole-rock dates ranging from 270 to 485 million years, dates which are apparently inter-mediate between the age of the source material and that of the metamorphism. "Up-dating" increases with the degree of orientation of muscovite in the cleavage plane, and with the ratio of the muscovite in the cleavage plane to that in the plane of the bedding. Detrital muscovite from four arenaceous rocks gave dates ranging from 1,050 to 1,780 million years. "Updating" increases with decreasing grain size, so that, within the range investigated, the cube of the median diameter (¢) of the muscovite is apparently proportional to the radiometric date.

Jan 1, 1964

By W. R. Middagh, R. M. Garvey

"Phosphate rock is shipped by boat from Florida to Vancouver, B.C., where it is unloaded and stored in a 50,000-ton silo. It is shipped from Vancouver in 100-ton hopper cars in 80-car trains to Fort Saskatchewan. Both the ship and the hopper cars are on a back-haul with potash. The rock cars are unloaded at Fort Saskatchewan at a rate of approximately 4 cars per hour. The rock is stored in three concrete silos, 40 ft in diameter by 110 ft high, which hold 18,000 tons of recoverable rock with 2,000 tons dead space. The rock is reclaimed from the silos by gravity and fed to the phosphoric acid plant by remotely operated conveying equipment.Problems encountered in the operation include scheduling the rock shipments, contamination of the rock with potash, and handling the 80-car trains both in Vancouver and Fort Saskatchewan."

Jan 1, 1968

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By S. F. LEAMING

Jade occurs with alpine-1ype serpe111iniIes in a be// of middle Paleozoic to Triassic rocks extending from southern British Columbia in10 Yukon Territory. Most known deposiIs are in BriIish Columbia and are associa1ed wi1h the Cache Creek Group. Jade deposits are generally small len1icular masses 1ha1 lie along con1acIs beIween serpenIinites and various countIy rocks; some are 1ec1onic inclusions wi1hin se1pen1ini1es. Qualify and quan1i1y of 1he jade varies widely. Deposi1s occasionally, but rarely, reach 3,000 /Onnes. The ma1erial may be rendered non-commercial by .frac1ures, impuriIies, inferior colour and poor IexIure. Because unit value of jade can approach $80.00 per kg, greaI incen1ive exisIs 10 exploi1 1his resource. Successful commercial operations, however, depend on large- *A more detailed version of 1hi paper occur in Leaming (1978). PHOTO I . Sawn blocks of nephrite ready for shipping. 270 volume sales, for which $6.00 to $15.00 per kg is more realistic. Many undiscovered jade deposits undoubtedly remain in the Canadian Cordillera.

Jan 1, 1984

By A. J. Faulds, K. C. Westaway, Z. Waszczylo

"PAH compounds have been found in the exhaust from all types of engines burning hydrocarbon fuels . They have also been found in the air over cities and in water. The authors report on a study to assess the concentrations of twelve different PAH compounds in several different environments in dieselized underground mines. In addition, the differences in the PAH levels and distributions in different mines will be demonstrated. Finally, the influence of blasting and the type of diesel engine used as well as the effect of catalytic converters in the exhaust system on the PAH concentration in the mine will be discussed.IntroductionMining methods have been altered significantly in the last 25 years; i.e ., the tools and machinery used underground have changed from electrically operated trains and other equipment to diesel-powered equipment. This has been done for several reasons: 1) economics, 2) convenience and 3) safety. Today, most mines are heavily committed to using diesel equipment.Although the introduction of diesel equipment has revolutionized mining methods and has been a tremendous boon to the mining industry, it has also created new problems. These problems arise because the exhaust from diesel engines contains several pollutants which can be hazardous to the health of the miners. These pollutants are CO2, CO, NO., SO2, oxygenated hydrocarbons produced during the buring process and unburned hydrocarbons. There are two classes of hydrocarbons, of which polynuclear aromatic hydrocarbons (PAHs or PNAs) are a part."

Jan 1, 1981

Background ArcelorMittal?s (formerly QCM?s) Port Cartier iron ore pelletization operations 2 side-by-side induration furnaces each producing 578 t/h of cured pellets Firing No. 6 fuel oil and coke breeze (in bed) Very large heat losses to be addressed primarily by gas recirculation

May 1, 2011

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By Janet S. Springer

Anomalous gold concentrations in carbonaceous material have given rise to misconceptions about the role of carbon in gold depo its. Some hydrocarbon and carbon-rich black muds may how gold contents raised to 100 time above background by mechanical entrapment. urface effect in fine ediments. and metabolic fixing of gold by micro-organisms. Such concentrates, however, are 10 times too low to be economic. Studie in the Archean of Ontario show that graphite schi t are not the protore to an economically workable gold deposit. A later event of gold introduction ha been uperimposed on the initial low concentrations. Gold enrichment i localized by reduction at vein margins where hear plane . the conduits of mineralization, cut carbonaceou horizons.

Jan 1, 1986

By D. Neely

As Saskatchewan potash mines grow in age and size, mining reaches greater depths.  The stress-relief design principals which were empirically derived at shallower depths are beginning to show fault.  Nutrien Vanscoy Potash has began to encounter new ground support and panel design challenges which were previously had negligible effect.  While the initial reaction was to reduce extraction and implement distance buffers between operating machines, it eventually became clear that these would only provide short term relief and that in order to continue safely and efficiently mining broad areas, a fundamental change in the mine design would provide the long-term protection required.  Presented is a case study with an overview of the challenges encountered at Vanscoy Potash in areas of greater depth along with an account of the design changes considered, implemented and recommended for future success. 

May 4, 2025

By G. S. Barry

INVESTIGATIONS to date have shown that, should there be the need or the appropriate economic stimulus, Canada's mineral resources are sufficiently extensive to allow considerable expansion of its non-fuel mineral industry, during the remaining part of this century and possibly beyond (1, 2). The availability of sufficient capital will be one of the critical factors which will determine whether this potential will be fulfilled. The following analysis centers on the capital requirements of the Canadian non-fuel mineral industry under one set of basic assumptions of capacity growth, cost of new and replacement capacity, rates of depletion and depreciation of mines and plant, and the cost of exploration and infrastructure. Mindful of the fact that exploration and development will not thrive in Canada unless a very positive approach is taken, the writers make no apologies for being "optimistic" about long-term production prospects. Furthermore, in the event that world demand does escalate as anticipated and the forecast realistically attainable levels of Canadian production are not reached, then Canada will not have reaped the full range of economic benefits available, and opportunities will have been lost. Projections for Canadian production between 1976 and 2000 are essentially based on the forecast published in the 1974 paper, "Towards a Mineral Policy for Canada - Opportunities for Choice (3), with some updating on the basis of recent developments.

Jan 1, 1977

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By Paul-Henri Girard

La Mine Agnico-Eagle division Laronde situé à Cadillac, est un producteur d?or, d?argent, de cuivre et de zinc. Cette propriété est situé dans les cantons Bousquet-Cadillac le long d?une des ceintures géologiques les plus productives au monde. La mine Laronde a débuté la production en octobre 1988 à un rythme de 1360 tonnes par jour. Ensuite, elle a augmenté son rythme de production successivement à 1800 TPJ en 1990, 3300 TPJ en janvier 2000 et 4500 TPJ en octobre 2000. Agnico-Eagle, fondé par feu Paul Penna, a toujours eu comme politique la participation des employés aux décisions de la compagnie pour le déveleppement de celle-ci. Cet écrit va permettre de mieux comprendre la façon dont la division fût développé.

May 1, 2001

By M. D. Everell

Le Centre de Recherches minérales (CRM), qui est un organisme de recherche appliquée du ministère de l'Energie et des Ressources du Québec, a été créé en 1969, dans le but de procurer un support scientifique et technique à l'industrie dans le domaine des mines et de la métallurgie. Pour atteindre ses objectifs, le CRM met à la disposition de l'industrie un personnel spécialisé et compétent dont une quarantaine d'ingénieurs et de scientifiques. Etant donné la nature même de l'industrie minérale, ce personnel est très versé dans l'étude des problèmes diversifiés des domaines de la technologie minière, du traitement des minerais, de la métallurgie extractive et de l'analyse minérale. Ce Centre de recherches met également à la disposition de l'industrie une usine-pilote permettant de reproduire les résultats du laboratoire au moyen d'un appareillage de type industriel, d'obtenir des échantillons en quantité suffisante pour une exploration du marché et de familiariser du personnel avec les opérations normales de l'industrie. Certaines de ses contributions récentes au développement de l'industrie minérale du Québec seront présentées.

Jan 1, 1985

By C Kumar

Scaffolds are temporary structures built to facilitate construction activities on site. A considerable amount of resources are allocated to scaffolding on industrial projects. Variability in geometrical features and space accessibility of structures on industrial projects, in addition to involvement of different trades that share the use of scaffolds, requires an extensive understanding of scaffolding requirements. Hence, it?s important to plan and estimate scaffolding man-hour requirements for the different construction areas on an industrial site. Contributing factors involved in such estimates include the list of trades that work in a construction area, trade working hours, volume of work, geometry of equipment erected, etc. A simulation template for predicting scaffold erection man-hour values for individual construction areas in an industrial project was developed in Simphony 4.0. The template is based on mapping the geometry of equipment and other factors to man-hours of scaffold work. The template facilitates the use of distributions as inputs and produces a range estimate of scaffold man-hours. The mapping is based on a linear regression model derived from existing project data from PCL Industrial Management Inc. The template is being further developed to incorporate the ability to predict scaffold erection schedule and material requirements based on construction work areas or equipment lists of an industrial construction project.

Aug 1, 2013

The steam-filtration process for dewatering solids involves the application of slightly superheated steam to a filter cake during filtration. The mechanism by which the technique promotes water removal has been deduced from bench-scale experiments on coal and on granular iron ore concentrates. The mechanism, along with some of the applications and limitations of the process, is presented. Introduction I N the steam-filtration process, slightly super-heated steam is applied to the filter cake during filtration to remove more water than can be extracted by conventional filtration. Although this process was developed by Burton for coal filtration (1), it should have far wider applicability; certainly, it could be used to treat any mineral product, because only low-temperature steam is needed and most conventional filtration equipment can be easily adapted to it. As few restrictions apply to this process, however, it is important that its more obvious advantages and disadvantages be appreciated and, especially, that the criteria on which economic evaluations can be based are understood.

Jan 1, 1965

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By P. M. Hedley

GOLD mining in Nova Scotia, as in any other gold district, has its own peculiar problems. Being in close proximity to excellent roads and to railways, and being blessed with good labour, the majority of gold mines in the Province find their paramount trouble is geological, namely, ore finding. After six years of continuous mining at Goldenville, the staff of Guysborough Mines, Limited, has collected many facts, has come to some definite conclusions, and has made a lot of guesses, some good and some bad. It is the purpose of this paper to set down such information as we have been able to gain in the hope that it may prove useful to other operators, present and future, faced with similar problems. What may be true of one Nova Scotian mine will not necessarily be true of another, so that the observations that follow should be considered as primarily applicable to Goldenville. Stated facts, conclusions, and theories are the result of the combined thought and effort of Head Office officials, of members of the Provincial and Federal Departments of Mines, and of members of the mine staff, past and present. Grateful acknowledgment is made to all.

Jan 1, 1941