Search Documents

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By C. J. R. Braithwaite, Giancarlo Rizzi

"The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. TheStackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grain-stone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is con?ned to the Meath Formation. The linear dolomite body,trending NE-SW, has a ?attened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing ?uids initially rose vertically, cross-cutting stratigraphic and sedimentological bound-aries, although ?uid ?ow was subsequently controlled by these features.Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL),oxygen isotopes, and ?uid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and ?uid inclusion data suggest growth of successive stages from waters which became progressively hotter(60°–160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore ?eld may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By C. J. R. Braithwaite, Giancarlo Rizzi

"Abstract-The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. The Stackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grainstone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is confined to the Meath Formation. The linear dolomite body, trending NE-SW, has a flattened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing fluids initially rose vertically, cross-cutting stratigraphic and sedimentological boundaries, although fluid flow was subsequently controlled by these features. Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL), oxygen isotopes, and fluid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and fluid inclusion data suggest growth of successive stages from waters which became progressively hotter (60°-160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages 1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage 3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore field may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By S. Ng, Peter Stapleton, Paul Mankowski, J. Spence, R. Siy

"Syncrude has developed a low energy extraction process for the recovery of bitumen from oil sand. This new process operates at a temperature of 25 °C, resulting in substantially lower energy costs and lower capital costs, especially for the thermal energy generation equipment. The process will be used in Syncrude’s Aurora Mine, which is scheduled for startup in mid 2000. The flowsheet for Low Energy Extraction includes hydraulic transport of oil sand slurry, and bitumen separation using collector and frother chemicals and air as process aids. A number of flow sheet innovations and optimizations have been included, resulting in the next generation of extraction technology. Experimental pilot plant results, engineering progress to date and areas of ongoing work will be discussed. SUMMARYThe Low Energy Extraction Process has been successfully developed for commercial implementation at Aurora. The 1996 100 tonne hour Field Pilot demonstrated that the bitumen recovery target could be met with an 11.1% grade oil sand. However, pilot plant bitumen recoveries for a lower grade oil sand were not acceptable. The subsequent flowsheet optimization study led to a new flowsheet for Low Energy Extraction, which includes a primary separation vessel, a flotation circuit for PSV middlings, and the use of middlings displacement in the PSV cone bottom with flotation underflow. A test program conducted in 1997 showed that the new flowsheet could significantly improve the bitumen recoveries for lower grade oil sands. Engineering work on process scale-up led to selection of a 30 meter diameter PSV, with a tangential feedwell. The successful development and commercialization of Low Energy Extraction for the Aurora Mine Project is a major enabling step in the Syncrude 21 program. The low energy requirements of this process allow Syncrude to develop the Aurora leases more cost effectively. The use of this process results in major capital cost savings, predominantly in the thermal energy infrastructure and also provides long term operating cost advantages for Syncrude."

Jan 1, 1999

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By Gordon W. Parsons, Ross E. Sampson

"THIS PAPER will trace the work done in bringing the Munro underground ""A"" •Orebody into production to replace the open pit, which was scheduled to be completed early in 1959. Included will be an outline of the exploration work and early planning, and of the final decisions on mining methods. Some of the more detailed work will be described and reasons will be given for the decisions made regarding development work, mine ventilation, ground support, and equipment. Brief mention will be made of open pit operations, as these have had some influence on underground development. Also, some of the main geological features of the ore occurrence will be de-scri0bed, as these had to be taken into consideration when making decisions on ore development and mining methods.LOCATION AND HISTORYhe Munro mine of Canadian Johns-Manville is in Ontario, approximately 50 miles east of Timmins and 40 miles west of the Que-bec-Ontari-0 boundary. The producing orebody is in the southwestern part of Munro township. Property controlled by the Company extends nortl1westerly about 2¥2 miles into Beatty township, on which two other interesting asbestos-bearing zones have been partially expl-0red. Active exploration work on the property was started in March, 194.9, and continued until the summer of 1950."

Jan 1, 1960

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

By S. Bergquist

In this paper, it is investigated how different types of automation would affect the safety for workers in asphalt paving. The risk for the workers on road construction sites is consistently high in comparison to the average risk of the working population. Automation has been suggested as an alternative for improving the safety in roadside construction assuming that removing workers will inherently eliminate the risk of them being injured. In this paper, the potential for improving the safety using automation is analyzed in detail. By investigating accident statistics and understanding the type of accidents that appear, several different automated functions for increased safety are proposed and described. Based on available statistics, it is possible to estimate the safety benefit, as the reduction in fatalities, for several of the proposed functions. The highest safety benefit would be achieved by automating the road traffic driving through the work zones. This has the potential of reducing the total number of road worker fatalities with over 30 %. In addition, it would decrease the number of road traffic accidents in work zones. Automation of construction machinery and dump-trucks also has the potential to increase the safety.

Aug 1, 2013

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

By L. R. Plitt

A new simple correlation has been developed to evaluate the performance of classifiers. The new correlation has been tested on existing data from 150 different hydro-cyclone classification tests. It is shown that this model provides a meaningful improved method of mathematically describing the classification process.

Jan 1, 1971

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By O. Lashkari

Manipulation of pouring temperature is an efficient way to produce different microstructural features. In order to characterize the microstructure of rheocast billets due to different superheats of 615-695 °C, the parallel plate compression method was employed. Foundry 356 Al-Si alloy with different morphologies of primary a-Al particles were tested at different initial pressures of 4,8, 11,2 KPa, The resulted strain-time graphs were further treated mathematically to calculate viscosity of SSM billets. The interrelationships of viscosity, the microstructure and primary phase flow during compression are discussed, It is shown that the dendritic primary a-Al structure has the highest viscosity number which is almost three orders of magnitude greater than those for globular morphology, The current research have, for the first time, shown the validity and reliability of "parallel plate compression viscometry" method in characterizing microstructural evolution of Rheocast SSM billets.

Jan 1, 2005

By G. M. Ross, J. A. Scott, C. A. Laamanen, H. Shang

"Indirect recovery and use of waste heat contained in smelter off-gas is proposed to expand regions available for year-round, on-site production of micro-algae–sourced biodiesel, a fuel that could be used in underground machinery. A dynamic model of an off-gas heat exchanger describes capture and distribution of heat into open, external, rectangular micro-algae ponds. Smelter off-gas contains sufficient energy to maintain large-scale micro-algae cultivation pond temperatures above 15°C, even with winter ambient temperatures below –15°C. Results highlight opportunities that could lie in tapping these heat resources to produce renewable biofuels on-site and sequester CO2 while leaving the industrial process unaffected.RÉSUMÉ On propose la récupération et l’utilisation indirectes de la chaleur résiduelle contenue dans les dégagements gazeux des fonderies pour développer les régions se prêtant à une production toute l’année durant et sur place de biodiesel à partir de micro-algues, carburant dont on pourrait se servir pour le matériel d’exploitation souterraine. Un modèle dynamique d’échangeur de chaleur contenue dans les dégagements gazeux décrit le captage et la distribution de la chaleur dans des bassins rectangulaires ouverts de micro-algues en extérieur. Les dégagements gazeux des fonderies contiennent suffisamment d’énergie pour maintenir les températures des grands bassins de culture de micro-algues au-delà de 15°C, même avec des températures ambiantes en hiver inférieures à –15°C. Ces résultats soulignent les possibilités que pourrait offrir l’exploitation de ces sources de chaleur pour la production de biocarburants renouvelables sur place et pour la séquestration de CO2 sans que cela n’ait d’incidence sur le procédé industriel.INTRODUCTIONMicro-algae that grow in water can efficiently convertsolar energy and carbon dioxide into biomass. This biomass can be up to 50% oils (lipids), which can be extracted and converted into biodiesel through transesterification (Demirbas, 2008). Compared to terrestrial plants that produce similar oils (e.g., jatropha, soybean, and rapeseed), micro-algae represent an order of magnitude increase in areal productivity, do not require arable land, and can be continuously harvested (Rawat, Ranjith Kumar, Mutanda, & Bux, 2013). The potential advantages through the production of biodiesel from micro-algae also include sequestration of carbon dioxide, reduced reliance on fossil fuels, and the co-production of other value-added bioproducts."

Jan 1, 2017

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005