Search Documents

By A. G. Scobie

THE research laboratory of this Company was recently faced with the problem of determining trace amounts of tungsten in a series of classifier sands. A spectrographie survey revealed the feasibility of using this instrument in the final evaluation, but a check of the common methods in use for the isolation of tungsten (3, 4) showed these methods to give incomplete separation for trace amounts. An investigation into the possibility of modifying these procedures, or developing others, was thus indicated. ASSAY PROCEDURE Weigh 10 grams of 200-mesh ore or concentrate into a 400-ml. beaker, wet the sample well with about 20 ml. of water, and add 100 ml. of hydrochloric acid. Cover, digest at 60° to 70° C. for about 1 hour, and then boil down to approximately 25 ml. Cool, add 25 ml. of hydrochloric acid and 10 ml. of nitric acid, and again boil to former volume. Add 20-ml. portions of nitric acid with successive boiling clown until chemical action is complete. Then add 20-ml. portions of hydrochloric acid until all nitric acid is removed. Take nearly to dryness on a law-temperature hot plate, but do not bake. Take up in 10 ml. of hydrochloric acid and 20 ml. of water and heat on a law-temperature hot plate until all iron goes into solution. Dilute to 200 ml. and heat to just below boiling. Stir in pulp of about half of a No. 41 Whatman filter paper (12.5-cm.) and continue digestion on plate with occasional stirring for 15 to 20 minutes.

Jan 1, 1943

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By W. A. Lang

RESEARCH has been defined as the link between the present and the future. Science, wonderful though its achievements may be, has but scratched the surface of the unknown. Research is directing its attention to winning new facts in order that their application to the processes of today may open up new sources of wealth for the common benefit. Two classes of research investigations are often recognized-fundamental and applied, but these classes merge into each other and it is often hard to distinguish one from the other. Fundamental research is carried out primarily to develop basic facts, but frequently these are found to have immediate economic value, while applied research, specifically aimed at economic values, often necessitates a preliminary fundamental investigation. Both are essential and both should proceed by scientific method. It is obvious in fuel technology that a knowledge of the physical and chemical constitution of the various coals is fundamental to their industrial utilization, and further, a knowledge of the way these coals react under different conditions of temperature, atmosphere, etc., is necessary in solving such problems as storage, combustion, carbonization, gasification, or con-version to liquid fuels. The wide range of coals, the complexity, of their constitution, and the many uses for coal, makes fuel research no simple subject but one with unending possibilities. The Research Council of Alberta, formerly known as the Scientific and Industrial Research Council of Alberta, was established in 1919, to promote the development and conservation of the natural resources of the Province. The work of the Council was arranged in six major divisions: Fuels; Geology; Road Materials; Soils; Natural Gas; and Forest Products. The office and laboratories are located in the University of Alberta. The Council was financed until the depression of 1933 by a separate vote of the Legislature, but since then has been continued, though on a much smaller scale, as one of the activities of the University. It might, however, be noted that although the Council is now in abeyance, a skeleton organization has been maintained so that it can be brought back to active service as soon as conditions warrant. Annual reports are still submitted to the Legislature. Funds have not been made available, however, for the publication of the last five reports.

Jan 1, 1942

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By O. W. Ellis

Introduction During the month of September, 1928 enough money had. been promised by private individuals and corporations to comply with the Research ?Foundation Act 1928 (Chapter 57, 18 George V) of the Province of Ontario. The Ontario Research Foundation (referred to below as O.R.F.) may be said to 1iave come into being at that time. Under the terms of this Act, the Treasurer of the Province was empowered to match dollar for dollar of the sums subscribed by private .corporations and individuals up to a limit of $1,000,000. However, the response to the appeal for this by the Premier of the Province, the Honourable Mr. G. Howard Ferg uson, was so exceptional that the Act was amended in 1929 so as to empower the Treasurer to increase the maximum contribution on the part of the Province to $2,500,000. In March, 1933, the Chairman of the Foundation, Sir Joseph Flaville, Bart., was able to report that, in the interval between the Premier&apos;s appeal and December 1st, 1932, private enterprise had paid ?into the treasury of the Foundation $1,670,050, and that the Provincial Treasurer had assumed responsibility for a like sum. The endownment Fund of the Foundation was, therefore. $3,340,100. This sum was ?invested a lm~ s t entirely in Government securities, in securities guar. anteed by the Government, and in 1mmicipal securities. Sir Joseph Flavelle remarked at that time that "The payment of $1,670,050 to the Endowment of the Foundation by private persons and corporations is a somewhat remarkable performance when it is remembered that for three of the five years the business of the country has been suffering from a severe depression". Since that time it has been the consistent policy of O.R.F. to live within the income derived (1) from the investment of its Endowment Fund and (2) from fees collected for services rendered.

Jan 1, 1950

By F. C. Grensing, W. R. Crib

Copper-15 Nickel-8 Tin alloy is a relatively modern material, having been discovered in the 1970’s. It has complexities with casting, hot working and interdependent solid state phase transformations. A key to the high reliability manufacture of wrought rods, bars, plates and tube is the casting technology, which limits segregation, promotes microstructural uniformity and enables hot working. The EquaCast® continuous casting process has enabled the production of a broadening variety of wrought forms with typical yield strengths ranging from 100 to 180 ksi (690 to 1241 MPa) depending on size, shape and temper. This paper reviews the characteristics of wrought Copper-15 Nickel-8 Tin products which have registration in AMS specifications (4596 and 4597) and MMPDS-04 (CN-1) for use in aircraft. The design limits, microstructures, fracture characteristics and tribological behavior will be examined. This alloy system is emerging as a material of choice for aircraft bearings, corrosion resistant oil and gas exploration components, machinery and demanding off-road equipment applications. ToughMet® 3 is an alternative or upgrade to conventional moderate and high strength aluminum bronze bearing alloys.

Jan 1, 2010

By M. Marchese

It is no secret that scarcity of fresh water is an issue that at a global level in the years to come will have a major impact on the business landscape. A number of projects, beyond the mining sector, could remain on paper only due to this. At the same time, this situation is seeing the rise of new business opportunities, such as development of technologies for more efficient usage of water, water recycling, and desalinization of sea water. Despite that most of Chilean mining facilities are located in the driest area of the world, business has developed strongly and actively for more than a century. However, the negative effect on the water reservoirs and the environment is, lately, resulting in the reduction of the authorized water rights. Holding Water Rights for any given volume does not guarantee that the resource will be available when needed. A recent report from the United Nations on global climate change indicates that global warming can be directly related to changes in the natural and human environment. Chile would not be an exception. The reduction in snow levels in the high Andes and reduced rainfall during the so called "Bolivian winter", have directly affected the replenishing of the underground water reservoirs in the lower parts of the valleys, where most of the extraction of the resource takes place. Mining facilities shall be designed to reduce potential environmental effects, using proven technologies, and considering the best practices available. These measures shall constitute a complete structural framework for the environmental impact assessment (EIA) of the Project. The measures to prevent and mitigate the impacts on the water resources shall be considered during the design stage of a mining project. Current and future mining projects in Chile are conscious that the increasing pressure on the limited water resources is becoming unsustainable, and are already facing the water scarcity and social pressure by implementing sea water desalination plants, including long pressurized pipelines to the mine sites (e.g. Escondida, Candelaria, El Morro, Regalito). This paper presents, in summary, an analysis of the present and potential future scenarios.

Jan 1, 2007

By M. L. Jeremic

Altered and unaltered coal from the Star-Key Mine near Edmonton, Alberta has been tested under compression and under tension. The test results showed that altered coal samples have an appreciably lower strength than unaltered coal. Altered coal samples do not give a linear load-displacement curve, peak strengths are poorly defined and yielding is observed over a range of loads, so the material can be regarded as relatively plastic. However, unaltered coal samples produce a linear loading curve with a high tangential modulus and an easily distinguished peak strength at which there is a sudden brittle failure. These findings lead to important differences in the theoretical design of ribs and pillars in underground mines in the two coal types. The substantial differences in the strength properties and behaviour of the two types of coal are governed by a higher intensity of cracks in the weathered coal. Two causes of the additional cracking can be suggested-subaerial weathering and subterranean weathering of the coal.

Jan 1, 1979

By E. M. Timoshenko, A. V. Tarasov

The results of laboratory, bench-scale and semi-commercial investigations of a method for adding surfactant (technical-grade lignosulphonate) to the process of pressure leaching of nickel-containing pyrrhotite concentrates have been discussed. Lt has been demonstrated that feeding of technical-grade lignosulphonate distributed along the length of an autoclave ensures a reduction in its requirement by a factor of 1.5 to 2 as compared with single-point feeding; it also results in a decrease by 5% in the unit requirement of metallized iron-bearing precipitator in the process of non-ferrous metals precipitation and reduces by 0.05 to 0.1% (abs.) the nickel and copper contents in the tailings of the given process. Technical solutions have been proposed for commercial introduction of the process.

Jan 1, 2004

By T. B. Williams

A SEARCH of the records indicates that evidences of accumulations of petroleum and natural gas within the boundaries of British Columbia were discovered at approximately the same time as were those of Alberta. They probably would have been developed as soon bad it not been for the fact that they are in such uninhabited parts of the Province. Even today, the seeps of the Flathead area, and the later discovered extensive seeps of the Peace River area, have been seen by very few people. From the geological evidence, there is reason for believing that British Columbia soon will be a petroleum producing Province. Fifty-eight operators, both companies and individuals, are now backing the money and the effort which they have invested with us, for the most part within the last three years, in a belief that this is so. The promulgation of the Petroleum and Natural Gas Act in 1947 marked the beginning of a new phase with regard to the exploration and the development of our petroleum and natural gas resources. Since August 15th, 1947, the date on which the Act came into force, the area under exploration bas increased from a few thousand acres, held by lease under the Goal and Petroleum Act, 1986, to 10,460,115 acres, including all active permits, licences, and leases. In addition there are 192,720 acres under application, bringing the total under issue and application to 10,652,835 acres. The total area is comprised of 105 permits, 20 licences, and 26 leases under the 1986 Act. The permits and licences, which ?represent active exploration and development, are held by a total of 82 companies and 26 individuals.

Jan 1, 1951

By P. T. Bloomer

Introduction Mining of the orebody of the Sullivan mine, which is owned and operated by the Consolidated Mining & Smelting Company of Canada, Limited, has reached a point where pillar extraction is rapidly becoming a major part of the operation. Very few of the larger pillars have been completely extracted; consequently, this paper contains much that is theory and expectation. Due to early mining methods and the physical characteristics of the Sullivan deposit, similar conditions may not exist in other older mines facing the problems of pillar extraction, but it is thought that the methods employed and those contemplated may be of general interest. History The Sullivan orebody, which is at Kimberley in the Fort Steele mining division of the East Kootenay district of British Columbia, was discovered in May, 1892, by Messrs. Sullivan, Smith, Cleaver, and Burchett. After passing through the hands of several owners the property was optioned in 1909, and purchased in 1910, by The Consolidated Mining and Smelting Company of Canada, Limited. Early mining was highly selective, the objective being a clean, high-grade silver-lead ore. By 1923 the difficulties of milling the very complex ore had been overcome and the first unit of a concentrator was completed with a capacity of 2,500 tons daily. Capacity was increased by stages to the present rate of 8,500 tons per day. Concentrates are shipped over the Canadian Pacific railway ? to the Company smelter at Tadanac, British Columbia, for final treatment. Approximately 45,000,000 tons of ore has been mined to date.

Jan 1, 1948

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world&apos;s thickest known coal beds.

Jan 1, 1977

By A. J. Reed, W. R. Bergey, Carr. J. M.

"The Highmont copper-molybdenum deposits are at Gnawed Mountain in the Highland Valley porphyry copper district, 125 miles northeast of Vancouver. This district is near the center of the lower Jurassic Guichon Batholith, where a north-trending swarm of porphyry dikes is crossed by west-northwesterly structural belts in which fracturing, intrusion of porphyry and breccia, and mineralization areconcentrated.The Highmont deposits are 2 miles southeast of, and in the same southernmost structural belt as, the Lornex deposit. The main deposits occur on either side of a composite dike of granodiorite, porphyry and breccia which strikes west-northwestward in fractured quartz diorite. North of the dike, the adjacent Nos. 1 (East) and 2 (West) zones together contain 150 million tons of open-pit ore mineable in two separate pits. These two zones will support a 25,000-tpd mill with a grade in the first five years of approximately 0.46 per cent copper equivalent. South of the dike, the Nos. 3 and 4 zones are partly explored and will provide large additional reserves. In these various zones, chalcopyrite, bornite and molybdenite form disseminations and fracture-fillings accompanied by quartz, K-feldspar, tourmaline, sericite, specular hematite and other minerals. Bornite extends for varying distances north of the dike, beyond which chalcopyrite is locally accompanied by pyrite. Higher-grade mineralization tends to coincide with fracture swarms, or with shear zones and faults which largely parallel these swarms. The ore zones are reflected by geochemical soil anomalies which show some glacial dispersion. LP. surveys gave weak but significant responses, expressed as per cent frequency effect. The ore zones occur within a strong magnetic gradient, but do not show a significant magnetic response."

Jan 1, 1971

By H. V. Kinsey

"IntroductionTITANIUM is probably the most widely publicized metal today. Much has been written, both in the lay press and the technical press, about its properties and potentialities. In view of the fact that Canada possesses large quantities of titanium-bearing ore, and could conceivably become a major producer of metallic titanium, it was felt that a paper dealing mainly with the physical metallurgy of titanium would be of interest to this Institute. This paper is concerned chiefly with the useful properties of titanium and its alloys and the fundamentals governing the modification of its properties by alloying.Physical Properties of TitaniumTitanium belongs to a family of metals that have been termed 'gas sensitive' (I), because their mechanical properties are altered by certain gases which they readily absorb and retain. Other metals of this group are zirconium, hafnium, vanadium, columbium, tantalum, and chromium. Titanium has a strong affinity for oxygen and nitrogen and once it has absorbed these gases they cannot be removed either by melting in vacuum or by any degassing agent. These gases, when present in excess of about half a per cent oxygen plus nitrogen, render the metal brittle and useless as a structural material.Some of the typical physical properties of titanium are listed in Table I along with those of common structural metals for comparison."

Jan 1, 1953

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By C. M. Diaz, S. W. Marcuson

In the late 19th century, the discovery of rich nickel-copper sulfide ore bodies in Sudbury and the need for tonnage quantities of the metal to be used in nickel steel armor provided the foundation for establishing the Canadian nickel industry. For almost 50 years, International Nickel was the key player. In 1930, Falconbridge Nickel entered the field. These two companies remain the key Canadian nickel producers. This paper discusses the factors that have influenced the evolution of nickel smelting processes. The initial Sudbury ore smelting and nickel copper separation technologies were imported from abroad. It was only in 1937 that International Nickel established a process research laboratory in Copper Cliff The explosive post WW II industrial development created a strong demand for a broader variety of nickel products. For both International Nickel and Falconbridge, R&D became an essential business tool to succeed in the new market scenery. In the last few decades, new technologies were developed and commercialized to respond to the raising cost of energy, society pressing environmental concerns, the advent of nickel laterites as an important source of new metal, the incorporation of new nickel producers to the market, and, therefore, the need to increase productivity. Canada thus became an important exporter of technology. In this paper, the authors review this history with the objective of highlighting the forces that have triggered the most important changes in Canadian nickel smelting.

Jan 1, 2005

By Alyson Morley

The mining sector in Canada is facing significant challenges to develop a competent workforce, including increased technical and logistical operational demands, and the imperative to promote local content. There is an increasingly unpredictable labour pool which can be aging, or have skill shortages, or non-aligned skills. As globalisation continues, companies also require efficiencies during operation across various locations. AMEC has met these challenges in the global oil and gas sector by developing our Capability Development and Competence Assurance (CDCA) program. CDCA is applicable across all process industries, including mining. CDCA supports simultaneous consistency and flexibility by defining competence at task level, with corresponding best practice blended training programs, and evaluation criteria and processes. CDCA then defines role profiles mapped to local task definition. When combined with web-based technology, this granularity allows us to manage high volume workforces, while retaining individual learning plans and progression, aiding job satisfaction, and employee retention.

May 1, 2007

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

By D. -A Tremblay

Dynamic wetting spread factors and interfacial heat transfer coefficients were determined for aluminum droplets solidifying on copper substrates, The spread factors were determined from the droplet geometries while the heat transfer coefficients were obtained by solving inverse heat conduction problems, 1-D and 2-D heat transfer models are presented and the results they provided are compared, For the latter, a sensitivity analysis was also performed to determine the influence of thermophysical properties and boundary conditions. Experiments were alternatively carried out with three different gaseous atmospheres and the dynamic wetting spread factors were correlated to the interfacial heat transfer coefficients.

Jan 1, 2005