Search Documents

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By Alan Reed

"Afton Mines Ltd. (N.P.L.) operates an 8500-tpd open-pit copper-gold mine near Kamloops, R.C. The pit is currently 480 feet deep and will reach an ultimate depth of 800 feet. The east, south and west walls of the pit are composed of Triassic andesites (Nicola Volcanic Formation) and contemporaneous sub-volcanic intrusions of micro-syenite, microdiorite, diorite and picrite-basalt (Iron Mask Pluton). The north wall of the pit consists of Tertiary sandstones, shales and mudstones (Tranquille formation) and dacitic dykes, sills, flows and tuff s (Kamloops Volcanic Formation).The Afton copper-gold orebody (30 million tons of open-pit ore with a grade of 1.0 per cent copper, 0.016 oz/ton gold and 0.12 oz/ton silver) occurs within the Triassic Iron Mask Pluton adjacent to its faulted contact with Tertiary rocks. The Triassic-Tertiary contact is a complex fault system dipping 65 degrees southward and causing the Triassic rocks to overlie the Tertiary rocks. The detailed trace of this contact is very intricate due to the mutual interference of three principal fault systems.The dominant geological structures in both Triassic and Tertiary rocks are faults striking WNW and dipping 65 degrees southward, i.e. sub-parallel to the orebody (strike faults). Cross faults and oblique faults are abundant and highly significant in some sectors of the pit. The Tertiary sedimentary rocks show an early series of northwesterly plunging folds deformed by a later series of northeasterly striking folds. Major lithological and structural boundaries divide the pit into 8 structural domain s within which the pitwall slope stability is controlled by the local geological structures and lithology.Assay data from production blasthole samples and exploration diamond drillhole samples show a log-normal frequency distribution, with a fairly low relative variance. Variograms computed from production blasthole samples show good continuity with elliptical horizontal zones of influence which are truncated by the major faults that bound the ore zone."

Jan 1, 1983

By R. C. Beard

"Heap leaching, currently being applied in the treatment of low-grade ores in the south western United States, is shown to have potential for use in north western Ontario. The history and operation of the process are described, and cost comparisons are given.IntroductionHeap leaching is a simple, low-cost method of recovering gold from low-grade ore. Although it is not currently being used in Canada on a production scale, it is being used extensively, and successfully, in the southwestern United States as well as elsewhere in the world. Especially suited for large deposits of very low -grade ore, it also appears to be practical for use on small, high-grade deposits because it avoids the high capital costs of mills. Eveleth (1980) and others suggest that the capital and operating costs required for heap leaching are approximately 20% and 40% respectively of conventional milling methods.Northwestern Ontario is noted for its large number of undeveloped, small, high-grade gold deposits. Although there are a number o f larger and higher-grade deposits in the area as well, it is the relatively small undeveloped deposits which would benefit most from heap leaching, if it could be demonstrated to be a viable extraction method.To assess the significance of these small deposits, the Ontario Ministry of Natural Resources recently commissioned a consultants' study of the gold reserves in certain parts of northwestern Ontario. This report, titled ""Feasibility of Small-Scale Gold Mining in Northwestern Ontario"", by J.N. Neilson and R.C.E. Bray (1981, OGS Open File Report 5332), documents 106 known gold deposits having sufficient information to calculate gold reserves. A total of over 7.8 million tons having a weighted average grade of 0.19 oz of gold per ton were compiled in the proven, probable and possible categories, with an additional 8.2 million tons in the speculative category. Many of these deposits could be mined by open-pit methods."

Jan 1, 1983

By E. Fritz

This paper reviews the history, developments and 10 milestones of the oxygen steelmaking processes, with a special focus on conventional autothermic converters, high-speed converters with a blowing rate up to 5 m3n/t min and allothermic converters with coal addition, post combustion and the possibility to increase the scrap rate up to 50%. Related operating results are introduced. A new process route, which is based on hot metal and chromium ore, is outlined. The cost advantage for the production of 304 stainless steel grade is higher than 100 USS/t. The synthesis of EAF and oxygen converter steelmaking, a comparison of decarburization rates, refining combustion burners for optimized oxygen-management in EAF and an example for a large advanced EAF are outlined. Possibilities of flexible steelmaking and the growth and outlook of worldwide oxygen steelmaking are described.

Jan 1, 2004

By G. F. Raymond, W. P. Armstrong

"At the time of this study, the Valley mine was producing 23 000 tonnes of ore per day from a large, low-grade porphyry copper orebody. Sulphide mineralization, principally bornite and chalcopyrite, occurs in a stock work of quartz veins in one phase of the Guichon Creek batholith. The property was explored from 1967 to 1982, and was placed in production in 1983.Using a three-parameter lognormal approximation developed by G.F. Raymond at Similkam een and Mount Isa Mines, a geo- statistical conditional probability ore reserve was estimated prior to mining. Comparisons with blasthole kriging and milled ore for the first 17 months of production showed close agreements at all cut-offs between conditional probability estimates and mineable ore. This was not true of either kriging or polygon estimates. An important part of this work was identifying and correcting for bias in both exploration and blasthole samples.IntroductionCominco's Valley lake deposit is a large, low-grade, porphyry copper orebody in the Highland Valley of British Columbia. Total indicated plus inferred ore reserves are 700 M tonnes at ore grade of 0.47070 Cu. At the time of writing, ore milling is at a rate of 23 000 tI d through the old Bethlehem mill. Mining is in 10m horizontal benches using 9.8 m3 shovels and 90 tonne trucks. Since this paper was written, Valley and nearby Lomex have been combined into Highland Valley Copper with a combined oreproduction of about 120 000 tI d.Copper mineralization, principally bornite and chalcopyrite, is regularly distributed throughout the deposit as disseminated low-grade within a granodiorite host rock, and as higher grade veinlets within a stock work of near-vertical quartz veins generally 10 cm or less in width. It is likely that problems with sample variability and sample bias are mainly related to mineralization within quartz veining. Valley geology has been described in detail by Allen and Richardson and by Osatenko and Jones (2). The exploration sampling program and identification of diamond-drill sample bias have been discussed by Armstrong and Newman'»."

Jan 1, 1988

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By V. G. Papangelakis, M. Cheung, M. Dry

The high pressure acid leaching of laterite was modelled and simulated using a combination of two commercially available software packages, namely Aspen Plus 11.1 and the OLI Stream Analyzer. New kinetic parameters for the acid-controlled metal dissolution and precipitation reactions at temperature were first determined from previous experimental data on the leaching of limonite. A grain model with cylindrical pellets was used to model the solid-liquid dissolution reactions. Precipitation reactions were modeled via aqueous equilibrium chemistry. A dedicated thermodynamic database previously developed at the University of Toronto was used in conjunction with the OLI software to model the solution chemistry and calculate the concentration of hydrogen ions in solution at the leaching temperature. Mass balances were handled by Aspen Plus. The simulation gave good predictions of nickel dissolution under industrial and laboratory conditions, for the dissolution of limonite and limonite/saprolite blends. Computational

Jan 1, 2005

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors' aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By M. J. Gole, R. E. T. Hill, S. J. Barnes

"The Agnew (also known as the Perseverance) nickel deposit and its northern extension, the Rocky's Reward deposit, form one of the world's largest accumulations of nickel sulphides hosted by komatiites. Agnew was previously classified as an ""intrusive dunite-associated"" deposit . It has now been shown that the sulphides are hosted by komatiite flows which underlie an adcumulate-textured dunite body that crystallized in a large lava channel.The rocks of the mine area have been subjected to a metamorphic temperature of550°C and pressure of up to 3 kb. The komatiites have mostly been reconstituted to olivine-amphibole chlorite assemblages. There is a zoned sequence of enstatite-, anthophylite-, talc- and antigorite-bearing assemblages inwards from the western margin of the ultramatic reflecting variations in the CO/HP ratio of metamorphic fluids.Facing directions are determined from variations in the proportions of metamorphic minerals and in rock compositions which reflect asymmetric layering in the flows . Olivine-sulphides matrix ore is hosted in a single 50 m thick, east-facing flow that is overlain by flows containing massive sulphides. Much of the massive sulphide has been physically remobilized into fold noses, faults and shear zones. Chemical diffusion of ore components has upgraded a sulphide-rich metasedimentary unit where it is in structural contact with massive ore.To the north, the mineralized flow sequence is separated from a stratigraphically higher komatiite sequence, the Perseverance ultramafic complex, by approximately 150 m of felsic meta volcanic and meta sedimentary rocks. Southward, the Perseverance ultramafic grades laterally into an olivine adcumulate body and its lower contact cuts progressively down stratigraphy until it lies directly on top of olivine-sulphide ore of the mineralized flow sequence. This discordant contact is interpreted as the base of a thermal erosion channel formed by a voluminous komatiite lava flow. This contact greatly influenced later deformation of the mineralized flow sequence."

Jan 1, 1989

By Nn Li

Energy consumption in commercial buildings has been increasing rapidly in the past decade. The knowledge of future energy consumption can bring significant value to commercial building energy management. For example, prediction of energy consumption decomposition helps analyze the energy consumption patterns and efficiencies as well as waste, and identify the prime targets for energy conservation. Moreover, prediction of temporal energy consumption enables building managers to plan out the energy usage over time, shift energy usage to off-peak periods, and make more effective energy purchase plans. This paper proposes a novel model for predicting heating, ventilation and air conditioning (HVAC) energy consumption in commercial buildings. The model simulates energy behaviors of HVAC systems in commercial buildings, and interacts with a multiagent systems (MAS) based framework for energy consumption prediction. Prediction is done on a daily, weekly and monthly basis. Ground truth energy consumption data is collected from a test bed office building over 267 consecutive days, and is compared to predicted energy consumption for the same period. Results show that the prediction can match 92.6 to 98.2% of total HVAC energy consumption with coefficient of variation of the root mean square error (CV-RMSE) values of 7.8 to 22.2%. Ventilation energy consumption can be predicted at high accuracies (over 99%) and low variations (CV-RMSE values of 3.1 to 16.3%), while cooling energy consumption accounts for majority of inaccuracies and variations in total energy consumption prediction.

Aug 1, 2013

By Geoffrey Gilbert

Rossland is in the West Kootenay district; 5 miles north of the International boundary and 4 miles west of Columbia River at Trail. The first claim in the district was located in 1887; but there was little activity until 1890; when the showings that later became important were staked and development began. Production increased rapidly from 1; 800 tons in 1894 to a peak of 360; 000 tons in 1903; and averaged 286; 000 tons for the next 13 years. It declined sharply in 1917; and continued to decline until the closing of the main mines in 1928. Between 1933 and 1941 leasers mined a further 137; 000 tons. Total output has been about 6; 200; 000 tons; with average recovery of 0.47 oz. gold; 0.6 oz. silver; and 1 per cent copper. The total value was $82; 500; 000; of which aboµt three-quarters was in gold; the camp still leads the province in total gold produced. Ninety-eight per cent of the tonnage came from a small compact area worked by four inter-connected mines : the Le Roi (39 per cent); Centre Star (25 per cent); War Eagle (24 per cent); and Josie (10 per cent); all now owned by the Consolidated Mining and Smdting Company of Canada; Limited.

Jan 1, 1954

By M. U. Savich

In Canadian mines, ear muffs are now an essential part of safety equipment. Because of this, a research study was conducted to investigate their efficiency. The main characteristics of eleven commercially available ear muffs were investigated in the laboratory and analyzed by: (I) a psychophysical method; and (2) a physical method. These investigations showed the following effects: head size has a significant influence on the attenuation because of a different clamping force; the amount of hair trapped between the ear muff cushion and the head decreased ear muff attenuation; attenuation and comfort are not in a causal relationship; with the use of glasses and their adapters, attenuation decreases-the adapters are not effective sound barriers; there are no great differences in attenuation with neck movement; the efficiencies of various brands of ear muffs are not equal; ear muffs with a small cushion area start serving their purpose more quickly because the force per unit area is larger; a clamping force larger than 900 g wt, in most ear muffs, does not cause an increase in attenuation; attenuation characteristics (ANSI 224.22 - 1957) of ear muffs show some correlation with physical tests. Nine ear muffs out of the eleven were tested under uniform conditions in mines. Three ear muffs were found to be the best. All three ear muff s have bands passing behind the head. The ear muff with a support strap, which improves comfort and maintains a good fit during wear, showed the best attenuation. Causes of poor attenuation are numerous: bad mounting of ear muffs on helmets, improper fitting, interferency by hair and glasses, improper wearing by miners, unsatisfactory enforcement by supervisory personnel, incomplete training of miners, etc. Results of this research have indicated that none of the ear muff s tested in this study contain all of the characteristics desirable in an ideal unit. Because of unsatisfactory ear muff attenuation in working conditions (/5 dBA), it should be a mandatory requirement that workers wear both ear muff s and ear plugs if the noise level is higher than 105 dBA (various literature recommends t io dBA). The key to the solution lies in the following: the foreman must be capable of helping and controlling miners in their task of wearing ear muffs properly; the program must be introduced to miners; and constant contact must be maintained with manufacturers.

Jan 1, 1979

By R. W. Diamond

PUBLIC debts, and the policies guiding public finance in Canada today, are in such a state that every intelligent citizen should be familiar with them, and should be concerned about them. None of you have robe reminded that taxes have already risen to a point where they both annoy and hurt you, but they should also alarm you; alarm you, not so much because of the taxation, but because of the mounting expenditures represented by that taxation. I have no hesitation, therefore, in presenting a paper dealing with public finance at a meeting of the Mining Institute, since all present are concerned,. both as individuals and as representatives of the industry. Moreover, it is important that engineers, particularly, should become better acquainted with the interlocking relationships of economics, public finance, government, and technology. While I am neither an economist, a tax expert, nor a chartered accountant, I shall try to tell you, from my viewpoint as an engineer and an interested voter, the story of public finance in Canada today and of certain causes and effects, and I shall venture certain conclusions. In doing so I may merit criticism by experts, but I will risk this in the hope that sufficient interest will be stimulated in the subject to persuade you, as individuals and as groups, to advance, or to institute, your own studies in public finance, and in turn to interest others. I hope that some of the ideas which will be expressed, or which may develop, will bear fruit. I fully realize that several eminently qualified men have spoken on this subject during recent months, and that many authoritative articles have been written. However, I approach it with confidence, because I propose speaking to you not as an authority, bur as one of you, having similar interests and similar engineering knowledge, who only a few months ago became particularly interested in the subject, studied it, and who now sets before you a summary of his findings, with the conviction that the situation is so serious that constructive planning and constructive action by all thinking citizens are imperative.

Jan 1, 1939

By W. B. Coker

A helicopter-mounted lake-sediment and lake-water survey was carried out over Grenville rooks in the Renfrew area (parts of Renfrew and Lanark counties) during four days of October, 1975. In the course of this survey. 1150 square kilometers were covered, with 246 lake-sediment and 276 lake -water samples collected from every body of water on which the helicopter could land. Sample sites, which averaged one per 4.6 square kilometers, included lakes, ponds, beaver ponds, swamps and marshes. Lake-sediment samples were taken using a G.S.C. sampler. Waters were collected directly into polyethylene bottles. At each sample site , surface and bottom-water pH, dissolved oxygen content, conductivity and temperature were measured using a Martel. Water Quality Analyzer. The lake sediments were air dried and then ball milled to pass a minus 80-mesh sieve. Lake sediments were analyzed for U by delayed neutron activation and for Mo, Cu, Zn, Pb, Fe, Mn, Ni and Co by atomic absorption techniques. The organic content of the sediments was determined by loss on ignition at 450 °C. Lake waters were acidified with nitric acid on the day of collection. The U content of the water s was determined by fluorometry; the Cu, Zn, Pb, Fe, Mn , Ni and Co contents of the waters were determined by solvent extraction - atomic absorption techniques. A close relationship was found between bodies of granitic, syenitic and pegmatitic bedrock and elevated U levels in the lake sediments. The Hurd Lake and White Lake granitic intrusive were encompassed by an annulus of higher U activity. Field inspection revealed that the U concentrations occur within a zone which may represent a contact metamorphic aureole. Within these complexes, anomalous concentrations of U appear to be associated with Mo. Information derived from the lake-water data reinforces the geochemical distributions outlined by the lake-sediment survey . This survey was carried out in order to develop optimum sampling and analytical procedures for geochemical reconnaissance of the Grenville Province that may be carried out under the auspices of the Uranium Reconnaissance Program.

Jan 1, 1977

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

A recovery process for rare earths (REs) such as dysprosium and neodymium from the leach liquor of permanent magnet scrap (PMS) was developed. The two hydrometallurgical routes namely liquid-liquid extraction (solvent extraction) and selective stripping were implemented. The present study deals with the separation and recovery process development by using organo-phosphorous based extractant di-(2-ethylhexyl phosphoric acid (D2EHPA) as reagent for REs processing. Initial studies considered the influence of time on the extraction process, as well as pH and extractant concentration effects. This suggested the aqueous mechanism and separation factors played a role in process during development. McCabe-Thiele diagrams for extraction isotherms were developed. Counter current extraction (CCE) using various phase ratios influenced metals separation. Maximum loading capacity of the D2EHPA was determined. The loaded organic generated by the CCE process was water washed followed by a scrubbing process to remove the other metal ion from targeted metal. Finally, a stripping process was tested using various mineral acids.

Jan 1, 2015