Search Documents

Contractors are used extensively in the development of underground mines in Australia. Often problems arise, some originating as far back as the feasibility stage of projects, through inexperience, lack of preparation and inflexibility by both parties.Guidelines are put forward for both principals and contractors which are seen as necessary to ensure that disputation is avoided and the full benefits of the use of contractors are obtained.

Jan 1, 1985

By B Tadesse, L G. Dyer, B Albijanic, M Jung

The presence of high concentrations of dissolved ions in groundwater, sea water or recycled water may alter the water structure, particle surface wettability and colloidal interactions between bubbles and particles and can have a significant effect on mineral flotation. While the impact of water quality on the flotation of precious and base metal minerals is well established, no relevant published study exists currently regarding the effect of water salinity on the flotation of rare earth bearing minerals. This paper attempts to quantify the effect of water quality variation on flotation recovery and grade of rare earth minerals and gain an understanding on which ions existing in saline water affect flotation behaviour. Specifically, it is aimed at investigating the effects of water quality on the flotation of monazite in the presence of cations such as Ca2+, Mg2+, K+, and Na+. Flotation tests, zeta potential measurements, and adsorption tests were performed to explain the flotation behaviour. It was found that monovalent ions such as Na+ and K+ have negative impact on rare earth minerals recovery and grade. The result of single mineral flotation tests showed that the floatability of monazite was significantly depressed in the presence of Ca2+ and Mg2+. The result of single mineral flotation test showed varying depression levels in the presence ions in the order of Ca2+ > Mg2+ > Na ~ K.

Aug 24, 2022

Water is required as a key strategic resource in most mining and metallurgical processes and, in some countries, it has become a limiting supply for the development of mining activity. During the last years, mining industry efforts have been successfully focused on water use efficiency in the different processes. However, these efforts will not be sufficient to compensate for the growing demand of mining products and the decrease of ore grades. New efforts should be oriented to the search for alternative water supplies such as sea water, with or without desalinisation, or water harvesting. But to survive this growing pressure and to get a social licence to operate, the mining industry can also assume a proactive attitude and pursue a prominent role in water management at regional and local scale. This paper reviews some of these emerging issues, particularly in the context of the Chilean copper industry.

Jan 1, 2009

By J Borthwick, M Yusi, M Douge

Feasibility studies form a vital and significant component of the project delivery cycle. They are at the heart of the valuation process. This paper focuses on variables which can affect a project and how these are assessed as part of the decision-making process through feasibility studies. Test work and site selection needs; the degree of engineering required to meet the study requirements and the quality of owner project information are discussed. Also, local factors including permitting needs, social, environmental and government relations are considered. Engineering and site factors are crucial in the estimating process. The interaction of detailed engineering, engineering assumptions and estimating methodologies are therefore examined. The ownerÆs perspective is considered along with risk analysis, which is fundamental in project feasibility study activities. The impact of this is also discussed.

Jan 1, 2009

The Snap Lake Phase I project initiated a subsampling campaign on the material (kimberlite/metavolcanic/granite) mined and treated for diamonds. The campaign was aimed at determining the optimum subsampling program to subsample the feed to the bulk sample plant (BSP) for the duration of a sampling campaign. This paper describes the application of GyÆs formula for determining the subsample size and other good sampling practices to determine this subsampling campaign. Three main issues are discussed: the use of a hammer sampler to sample off a moving conveyor and the practical experiment to determine the optimum subsampling program; bias introduced by laboratory equipment including two sizes rotary splitters; and variability of the feed material to the BSP over time.

Jan 1, 2005

By T Klinge, P Field, N Sugden, D Trenberth

Mining remains one of the key industries in Australia and many other countries with mineral wealth. In Australia, mining contributes 8.8 per cent to the countryÆs gross domestic product (McKay et al, 2000). In Queensland alone, mineral and petroleum industries contribute approximately $9.4 billion to the StatesÆ gross state product (2001/02) (Young, 2003). Increasing pressure on mining companies to perform in a global marketing environment requires mine management to consider more innovative ways to manage their resources û human, plant and equipment û which includes the gathering and analysis of operations data and information for improved decision making. For any mining operation utilising rubber tyred equipment such as trucks, front-end loaders and ancillary equipment, annual expenditure on tyres and related items can be significant. Even a small reduction in tyre operating costs can have a real effect on the business bottom line performance in the short term. Tyre Application Risk Management (TYREARMÖ) can provide substantial benefits in the long term across a number of KPIs not just through reduction in direct tyre expenditure but through flow-on improvements in safety, productivity and reduced environmental impacts. Several accidents involving tyres have also highlighted an increased need to consider the hazards and resultant risks arising from operations of rubber tyred mining fleets (Torlach and Johnston, 1990). This paper presents the process and results of achieving sustained safety and business improvement through the strategic alliance between an earthmover tyre management service provider, Klinge and Co (Klinge) and a BHP Billiton coal mine. The accompanying case study demonstrates in some detail the overall methodology, and the tools and technologies used where active management of data, its analysis and decisions taken have resulted in a 43 per cent improvement in tyre cost performance and a corresponding reduction in tyre-related downtime since the beginning of the alliance.

Jan 1, 2003

By R Smart

This paper examines the longer-term predictive capacity of the GAMSPATH computer program (developed by the Alberta Research Council) for a waste rock (sample MS) obtained from the Kaltim Prima Coal (KPC) mine, Kalimantan that contained significant framboidal pyrite. The model was refined by comparison with the net acid generation (NAG) and column leach tests to provide a basis for calibration of the model for both short term and longer-term reaction trends. The oxidation of pyrite during the kinetic NAG test using H2O2 provides oxygen directly at the mineral surface, generating a measured oxidation rate for pyrite of 1.16 + 10-6 mol m-2 s-1, whereas the oxygen diffusion limited rate in the leach column air equilibrated reaction was of the order 10-8 mol m-2 s-1 as calculated from the GAMSPATH thermodynamic database. Results indicated that the oxygen derived from hydrogen peroxide had to be included as a reactant (eg a reacting mineral) in the simulation to account for the direct availability of oxygen at the sulfide mineral surfaces. Optical investigations identified the proportion, particle size, and surface area, of framboidal and euhedral pyrite in sample MS. The reactive surface areas of the two morphologies were very different (eg ratio: 5:1). To manage these two different pyrite morphologies the GAMSPATH thermodynamic database was updated to include framboidal pyrite, with similar thermodynamic properties and oxidation rate to euhedral pyrite but with a particle size based on the size of the individual internal framboid microcrysts. This modification, with framboidal pyrite reaction based on the size of its microcrysts produced results that correlated well with the kinetic NAG and column leach test results when the measured (kinetic NAG test rate) and calculated (column test rate) pyrite oxidation rates were employed. This provided some confidence that the model could be extrapolated to indicate longer-term geochemical reaction trends.

Jan 1, 2003

By Ken Campbell

Exploration and mining in Third World countries will essentially be an exercise in the transfer of technology. We must not underestimate the effort it will take to develop the necessary industry peer group in these nations which can accept the latest western technology and use it to good effect.

Jan 1, 1994

The undeniable fact of life in the next 25 years will be the increasing difficulty of the physical conditions of Australian orebodies facing future miners. We are all familiar with names such as the 3000 orebody at Mt Isa, Hilton, Century, Macarthur River, Cannington, and Ernest Henry. These projects represent a significant. proportion of the planned underground mine development in Australia. Moreover, many of these new orebodies are an order of magnitude more difficult to mine and process than their predecessors. Extraction will be from deeper and potentially more hazardous working environments. Occupational health and safety considerations will place unprecedented demands upon mine operators and technology providers of the future.

Jan 1, 1994

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994

The mmmg of alluvial gold involves many deposits of theMesozoic, Tertiary, and Quaternary Ages in processing. Majorfeatures of the composition of such alluvial deposits are the lowcontent of gold and the small size of the gold particles. Atpresent, the gold-miners treat alluvial deposits in which a portionof fme gold (0.25 mm) exceeds 45 per cent. It is expected that by2000 these resources will be the main deposits mined (Zamyatinet aI, 1991).Under real industrial conditions the losses of minus 0.25 mmmetal are 50 per cent and more. The low level of recovery of finegold is observed not only at concentrators equipped with sluices,but also at concentrators equipped with modern diaphragm andpistonless jigs (Table 1).

Jan 1, 1993

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By R Mackay, J Brereton

On 30 June 2020, the Mine Land Rehabilitation Authority (the Authority) superseded the Latrobe Valley Mine Rehabilitation Commissioner as the independent overseer of Victoria’s declared mine rehabilitation. Currently, only the Latrobe Valley’s three brown coalmines are declared, with each mine at a different stage of rehabilitation and closure planning: Hazelwood ceased mining in 2017, Yallourn is scheduled to end mining in 2028 and Loy Yang in 2035. The three declared mines are very large, close together (Figure 1) and present significant environmental risks that must be mitigated during rehabilitation and post closure. In addition to fire risks, the brown coalmines are inherently unstable and require continuous monitoring and management of ground movements and groundwater pressures. Since 2007 several damaging events have occurred, highlighting the difficulties of achieving long-term stability, even with good landform design and rigorous ground control management plans

Aug 2, 2023

By A Prill

Safety First and zero accidents are the targets most mines in Australia are aiming for, but manual processes and procedures limit the capabilities and response time in emergency situations. Even with a high safety focus, accidents and incidents still happen, too often with tragic outcomes. Dangerous areas, narrow roads and winding curves are all daily obstacles that threaten workforce safety. Every unforeseen event, such as traffic collisions and other accidents, puts lives in danger and weakens production. Safety must be guaranteed.

May 5, 2022

Dr Eric Bumstead is to be commended for his recent paper on gold analysis, published in the March 1984 Proceedings. It is not often that someone in industry, rather than academia, takes the time to collect and report on such a volume of data, data which is of interest to everyone involved in gold exploration and development.After reading the paper I felt, as a geochemist and as ayer, that there was another side to this whole question of analysis that few people are aware of, i.e. the problem facing a laboratory and how the laboratory can try to give the customer maximum value for money spent.Analyses for gold are carried out for different reasons, depending on the aims of the geologist or metallurgist who presents the samples. These can broadly be separated into three classes, to answer the following questions.1. "Is there any gold in this sample?"2. "Approximately how much gold is there in this sample?"3. "How much gold is there in this sample?"In every case there is a different balance between accuracy and precision, cost and avoiding chemical problems. By "chemical problems", I mean such possibilities as samples containing high levels of sulphides, gold present as tellurides, cyanide being present, contamination with mercury, and other mineralogical oddities, plus problems such as samples containing grease.There is no such thing as one assay to cover all possibilities.Samples in category I come mostly from early stages of exploration.There are often large numbers of samples, their mineralogy is not well known and hence chemical problems could exist, but the explorer wants assays at a minimum level of precision and expects minimum cost. These characteristics do not easily come together, for although the precision required is low, the accuracy required is high at low levels. A small positive result when the true answer is nil could lead to a fruitless search and a waste of money. Conversely, a nil result, when the true answer is a small but significant level of gold, could lead to the passing over of an area that may warrant further work.Because there are conflicting requirements for this type of assay, the methods chosen must be a compromise and different assayers will balance these requirements differently and come to different conclusions. The methods cover sample preparation, assay sample size and variations in assay techniques.

Jan 1, 1984

By A G. Dempster, B McKeown, S Saydam, J Coulton

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By A McKay

The Great Artesian Basin (the Basin) is a large aquifer system underlying more than 20 per cent of continental Australia and most of Queensland. The aquifers of the Basin are an important water source for many industries, including the mining sector. The Queensland Great Artesian Basin Water Resource Plan (the Plan) was released in March 2006. The Plan provides a framework for the long- term holistic management of the aquifers in the Queensland Section of the Basin, in a manner that is consistent with the strategic management plan for the Basin as a whole. The paper describes the Basin and summarises trends in the demand for water in the Queensland section of the Basin. It describes the broad framework for management of the Basin by the individual Australian states, as well as the planning entitlement framework for water resource management in Queensland. The paper discusses the content of the Plan. This includes: the division of the aquifers into management areas and management units for management purposes, provision for protection of the flow of water to springs, limits on further allocating water, provision for a competitive process for access to new water and provision for water trading. Under the Queensland planning and entitlement system a resource operations plan is prepared to specify operational arrangements to implement a water resource plan. A resource operation plan for the basin is expected to be finalised before the end of 2006. The paper summarises the likely content of the plan.

Jan 1, 2006

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

Good morning and thank you for the opportunity to address this yearÆs New Zealand Minerals Conference.   As you have already heard from the Associate Minister of Energy, the Government believes that the minerals industry is an important part of our economy. In particular, our coal and lignite resources have the potential to play an important role in New ZealandÆs energy sector as both a primary fuel and as a means to produce electricity.   The Government has taken a keen interest in the primary fuel sector given the declining reserves of natural gas sector. The energy sector is a key driver of economic growth and it is therefore critical that we have a reliable supply of primary fuel as part of the energy mix.   In a global sense, New Zealand is like many other countries regarding the need to secure energy for the future. Natural gas will be a key bridging fuel in the transition from an energy market based on fossil fuels to one based on renewables over the next century.   However, natural gas as a solution to this energy transition has some pragmatic limitations for New Zealand. There is uncertainty as to when new domestic reserves of gas can be discovered and developed. And the alternative of imported LNG poses a number of costs and risks to the economy.   New ZealandÆs coal resources are vast-estimated to be enough to last hundreds of years at the current rate of extraction. The main question is can extraction be increased and sustained to meet the demand of domestic power producers and at the same time meet commitments to lucrative international markets?   At this point it is appropriate for me to place coal into context with Governments overarching policy objectives for energy. The Government has stated objectives for the energy sector emphasising energy efficiency and an increased focus of renewable energy, while still ensuring security of supply and certainty as to energy costs and risk. Coal certainly can make a contribution to these objectives going forward.

Jan 1, 2005