Search Documents

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By G Barla

In Europe, a major interest in the infrastructure and tunnelling fields is in the new crossings of Alps in the form of base tunnels, which are important components of the high-speed (for passengers)/high-capacity (for freight) Trans European railway corridors. These tunnels cross the mountain belt at the elevation of the main cities and basins located all around the Alps and are longer (up to 57 km) and deeper (up to 2500 m) than all tunnels constructed in the centuries before. The excavation of the first Alpine railway and road traffi c tunnels could in general be carried out successfully by conventional excavation methods. With the great lengths of the new base tunnels, mechanised excavation by using tunnel boring machines (TBMs) is imperative as it contributes significantly to savings in construction time and costs. Questions are however posed on the adoption of such a systematic tunnel construction method given the severe ground conditions which are some time anticipated along the tunnel alignment, with possible major geological hazards such as water inflow in heterogeneous fractured or karstifi ed rock masses, stress-induced tensile failure of hard rocks, and plastic shear failure and squeezing of weak rocks, etc. This lecture is to briefly review the current state-of-the-art in the understanding and modelling of two such critical hazards as spalling/bursting and squeezing ground behaviour. With the present interest in the design of mechanised tunnelling with TBMs in such conditions, the complex interaction between the rock mass, the tunnel machine and its system components, and the tunnel support is studied in detail by numerical modelling. The research and development efforts presently underway with the intention to provide the designer with a novel three-dimensional (3D) simulator of mechanised tunnel excavation are presented. Case examples are discussed with reference to the Lyon-Turin Base Tunnel design.

Mar 8, 2011

By T O Aspinall

The Australian mineral industry involves a diverse range of expertise and skills. Within that, the mining industry, representing mine planning, mine management and equipment operation, has capital intensive, high productivity equipment and a small but skilled workforce. Continuing education for all personnel in the workforce after formal school courses will be an important contribution towards improving competitiveness. The non-tertiary sector represents a significant proportion of the workforce and requires as much attention as the tertiary educated group. Competency Based Training is now being developed for the mining industry in Australia under the National Training Board and the mining industry is well represented in establishing standards and curriculum. TAFE is a major source of accredited courses but some mining companies are also developing internal courses not necessarily for external accreditation. Articulation of such accredited courses to tertiary mining engineering courses has been considered. The education and training of equipment operators through continuing education requires attention to operating skills, an understanding of the productivity factors under the direct influence of the operator and providing product quality to the customer. The education and training of mining engineers has been widely covered and continuing close involvement of the mining industry is required to ensure well balanced courses in technical and interpersonal skills as well as motivation to continue learning for life. Postgraduate research is a part of continuing education but the mining industry has to continually address the adequate recognition of post-graduate qualifications for the increased technical or management expertise and the development of better analytical and problem solving skills which can be directed towards improving competitiveness. More attention has to be paid to providing adequate financial incentives to attract suitable students, particularly after attaining some experience, and to address their professional career path with a company so they are not significantly disadvantaged by undertaking post-graduate studies. The Chartered Professional Engineer status as provided by The Institution of Engineers, Australia to qualified candidates is being considered by The Australasian Institute of Mining and Metallurgy as a further recognition of a member's specific expertise and competence in mining and metallurgical engineering. Continuing education plays a major part in the maintenance of the expertise and competence required for a professional engineer to develop and also to retain chartered status. Continuing education will be a significant part of the education and training of all the mining workforce towards improving the competitiveness of the mining industry. The major challenges will be the motivation of all towards lifelong learning and the integration of the various programs towards providing the opportunity for a steady and satisfying career progression.

Jan 1, 1994

The mining of Australia's rich and diverse mineral resources has been central to the development of the continent by "Europeans" over the past two hundred years. Mining has historically been encouraged (to varying degrees) by development-orientated state governments (the. managers of largely Crown-owned resources) and since Federation, by successive Com- monwealth governments (which have seen mineral development as a means of generating export revenue to fund predominantly social-welfare orien- tated budgets). This marriage of convenience between governments and the mining industry has to date served all parties well. However, Australia's entry to a new world economic environment at a time that community percep- tions are changing (owing to an education-inspired challenge to "old" values) is challenging the hitherto held assumption that mining develop- ment is always aligned with the well-being of the State and community. Issues such as the type and extent of State/Commonwealth government taxation, resource ownership and control, the environment, land use con- flict, the extent and desirability of secondary processing and infrastruc- ture funding are being debated in the public arena. Opponents of mining in the community are well-organised and are well funded, articulate and more importantly, they have effective communication channels with most governments, irrespective of political complexion. Apart from some television-orientated corporate image building and recent efforts by AMIC, the industry's response to this challenge has been unco-ordinated, poorly directed and arguably ineffective. Professionals working in the industry are concerned about the community's perception of themselves and their industry. Recognizing that the Australian democratic system ensures that, in the large, government at its various levels, is reflective of and responsive to the views and aspirations of people, the industry's response must be wide- ranging, equally articulate and couched in a form which is politically acceptable. New objectives in providing information to the public and its educators must be formulated. Moreover, professionals are looking for new directions from industry leaders. The Institute is well placed to facilitate this process.

Jan 1, 1988

By Gibbons S. L, Ritchie I. M, Murr D. M

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1990

By Lin Bin, Qain Minggao, Qu Qundi, Yao Zhichang

This paper describes the application of a 89C52 chip microcomputer in hydraulic pressure information monitoring system of powered supports in a coal face, and the details of circuit and software of a monitoring system substation. Each substati

Jan 1, 1998

By Callinan AN

Broken Hill Proprietary Company Limited have recently commissioned a 14 Megawatt power station adjacent to its underground coal mining operation at Appin NSW. The power station is fuelled by methane gas extracted from the coal seams 500 metres below the surface. The methane is compressed and cooled prior to its injection into the combustor of a single shaft gas turbine. The turbine is coupled through a reduction gearbox to an alternator. There is sufficient power generated to cover colliery load, with any excess being exported to Prospect County Council, which is the supply authority for the south western region of Sydney.

Jan 1, 1987

An assessment has been made of six reported methods for the determination of the swelling of iron ore pellets on reduction. The methods are discussed on the basis of apparatus requirements, reduction conditions, sample requirements, measurement of swelling and reproducibility. It is concluded that the CNRM, LKAB, and Lurgi methods are the most satisfactory which presently exist for determination of the swelling of industrially produced, iron ore pellets.

Jan 1, 1974

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

Nordberg has conducted extensive research, during 1982-85, on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Nordberg's engineers have developed advanced design and testing techniques that ensure efficient and reliable crusher designs. Combination of this knowledge has resulted in a design of the MPI000 (1000 hp) crusher which fits on the existing 7ft Symons foundation and yet is capable of producing twice the ton- nage of the 7ft. In this paper the development of the MP1000 crusher and its performance compared to the 7ft heavy duty and super heavy duty crushers will be discussed. Also, substantial cost savings resulting from the application of such a high performance machine will be presented.

Jan 1, 1988

HISTORIC SIGNIFICANCE OF EXPLOSIVES TO MINERAL PRODUCTION The ancient method of breaking rock was to build a wood fire against the face, heat the rock through and then pour water on the heated ore-bearing rock to cause it to break by tension. It was too slow and costly as the forests around the mines were cleared and transport of wood became difficult. Black powder had been used for 300 years as a gun propel- lant. ('Black' after Berthold Schwartz, a German monk, Figure 1, and the inventor of the gun who was given the epitaph `Here lies Berthold the Black, the most abominable of inhumans who by his invention has brought misery to the rest of humanity'). Only at the beginning of the 17th Century, black powder was introduced for loosening rock in European mines. In 1802 Dupont started black powder manufacture on the Brandywine Creek. The ignition train of powder was enclosed in goose quills, straws, rushes, paper or wooden tubes. The time interval between igni- tion and blast was pure speculation.

Jan 1, 1988

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980

By Treglown N

In any mining operation the curtailment of rising operating costs is of prime concern to management.One area of activity where costs are often disguised is that of longhole secondary breakage.This paper outlines sane operational techniques that have been considered and tested, resulting in improved fragmentation fran longhole stope blasts at New Broken Hill Consolidated Limited mine, Broken Hill, NSW.

Jan 1, 1985

By McHaina D. M, Hardcastle S. G

A description is given of an investigation into the feasibility of using controlled recirculation of warm exhaust air into the cold intake air of underground mines during winter. Canadian mines can experience inlet air temperatures of minus 30 ¦C and less, requiring them to pre-heat their intake air. The use of controlled recirculation would reduce the inlet air quantity and thus reduce heating costs which exceed $1M on some mines.

Jan 1, 1988

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, W.A. plant is briefly described. The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1979

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

A review is given of progress made to- wards the development of personal gravimetric dust sampling for risk assessment on South African gold mines. The present strategy is critically examined on the basis of principles for assessing health hazard from dust exposure. Reasons are advanced for replacing the konimeter with a gravimetric system based on full shift personal sampling. Constraints imposed by local characteristics of gold mines are used to illustrate the difficulty in finding suitable instrumentation for measuring personal exposure to respirable silica.

Jan 1, 1988

The New Southern Railway (NSR) involves the excavation of approximately 10 km of single bore tunnel from Tempe Reserve, Tempe, to Prince Alfred Park (PAP). PAP is located just south of Central Railway Station in SydneyÆs Central Business District (CBD). From Tempe Reserve the alignment takes the tunnel under Sydney Airport including the main north/south runway. Sydney Airport is approximately 8 km south of the CBD. The NSR is being constructed by a private group, the Transfield Bouygues Joint Venture (TBJV). Transfield is a major Australian contractor and the French contractor, Bouygues, is providing the soft ground tunnel construction expertise and is also responsible for the design of the concrete segmental lining. This paper sets out to present in some detail the issues involved in tunnelling under the airport and in particular under the north apron, the main north/south runway and the new elevated roadway. The paper concentrates on these three areas on the airport with an emphasis on the following. The risks involved and measures taken to minimise the risks in tunnelling under the International Terminal north apron (with Jumbo Jets parked immediately above). Secondly, settlement predictions, settlement and runway operation criteria and the actual settlements that have occurred on the main north/south runway. Finally, the criteria that was developed during the construction of the deep bored piers for the elevated roadway at the Domestic Terminal as the TBM passed through this area of construction activity.

Jan 1, 1999